Add DT definitions for PRCM (Power/Reset/Clock Management) clock and reset
controller subdevices.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The APP4 EVB1 development boards embeds an A31, together with some NAND, one SD
card slot, and one SDIO + UART WiFi and Bluetooth chip, a few I2C buses, USB,
and a LCD display.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>

The A31 has two ECHI/OHCI controllers, and one OHCI-only phy-less controller.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>

The USB clocks of the A31 seems to be parented to the 24MHz oscillator, and
handle the clocks for the USB phys and OHCI devices.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>

The R7 tv-dongle is an A10s based hdmi tv dongle, with 1G RAM, 4G nand flash,
and rtl8189es sdio wifi. It has a standard male hdmi connector, an USB host
port using an USB-A receptacle and a micro-usb receptacle for both power
and USB OTG.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The CubieTruck has an AMPAK AP6210 WiFi+Bluetooth module. The WiFi
part is a BCM43362 IC connected to MMC3 in the A20 SoC via SDIO.
The IC also takes a power enable signal via GPIO.

The WiFi module supports out-of-band interrupt signaling via GPIO,
but this is not supported in this patch.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The cd pin settings have been taken from the original firmware fex files,
and have been confirmed to work on the actual boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds  pin-muxing info for the mmc controller / port combinations which
are known to be used on actual boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the 4 mmc controllers found on A20 SoCs to
arch/arm/boot/dts/sun7i-a20.dtsi.
Signed-off-by: NDavid Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a new sun6i-a31-m9 dts file for the Mele M9 / Mele A1000G Quad. These
HTPCs use the same board in a different case, for more details see:
http://linux-sunxi.org/Mele_M9Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the 4 mmc controllers found on A31 SoCs to
arch/arm/boot/dts/sun6i-a31.dtsi.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add clk-nodes for the mmc clocks.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The cd pin settings have been taken from the original firmware fex files,
and have been confirmed to work on the actual boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the 3 mmc controllers found on A10s SoCs and for the 2 mmc
controllers found on A13 SoCs.
Signed-off-by: NDavid Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Tested on a subset of these boards, for the others boards the settings match
the ones of the tested boards according to the original firmware fex files.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

mmc0 is the only controller actually being used on boards, so limit the
pin-muxing options to that.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the 4 mmc controllers found on A10 SoCs to
arch/arm/boot/dts/sun4i-a10.dtsi.
Signed-off-by: NDavid Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds  pin-muxing info for the mmc controller / port combinations which
are known to be used on actual boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds  pin-muxing info for the mmc controller / port combinations which
are known to be used on actual boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable the PWM for both PWM channels on the cubietruck. They can be found on
connector CN8.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add the PWM bindings for the Allwinner A20.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add the PWM bindings for the Allwinner A10.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add the pinctrl descriptions for both PWM channels of the Allwinner A20.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add the pinctrl descriptions for both PWM channels of the Allwinner A10.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable the performance monitoring unit found in the A31 SoCs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>

Enable the performance monitoring unit found in the A20 SoCs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>

Now that we have a DMA driver, we can add the DMA bindings in the DTSI for the
controller and the devices supported that can use DMA.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The DT are supposed to be ordered by physical address. Move the NMI node where
it belongs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The prcm lives at address 0x01f01400 as the reg entry in its node already
correctly indicates, rename the node to match this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some versions of gcc even warn about it:

  mm/shmem.c: In function ‘shmem_file_aio_read’:
  mm/shmem.c:1414: warning: ‘error’ may be used uninitialized in this function

If the loop is aborted during the first iteration by one of the two
first break statements, error will be uninitialized.

Introduced by commit 6e58e79d ("introduce copy_page_to_iter, kill
loop over iovec in generic_file_aio_read()").
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On 32 bit, size_t is "unsigned int", not "unsigned long", causing the
following warning when comparing with PAGE_SIZE, which is always "unsigned
long":

  fs/cifs/file.c: In function ‘cifs_readdata_to_iov’:
  fs/cifs/file.c:2757: warning: comparison of distinct pointer types lacks a cast

Introduced by commit 7f25bba8 ("cifs_iovec_read: keep iov_iter
between the calls of cifs_readdata_to_iov()"), which changed the
signedness of "remaining" and the code from min_t() to min().
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>