pm_runtime_{use,dont_use}_autosuspend() controls whether the device's
sysfs power/autosuspend_delay_ms file is writeable or returns -EIO on
access to user space. Since

commit 25b181b4
Author: Imre Deak <imre.deak@intel.com>
Date:   Thu Dec 17 13:44:56 2015 +0200

  drm/i915: get a permanent RPM reference on platforms w/o RPM support

this sysfs file is writeable also on platforms without RPM support, but
userspace (at least IGT) depends on this file being unchangable to
determine whether the device supports runtime PM at all. So restore the
old behavior.

This gets rid of igt/pm_rpm failures on old platforms without RPM
support, where the test should be skipped.

Testcase: igt/pm_rpm/basic-rte
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450371873-878-1-git-send-email-imre.deak@intel.com

Use dev_priv rather than dev pointer where applicable. Remove plenty of
unnecessary temp variables. No functional changes.
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450428695-28831-1-git-send-email-jani.nikula@intel.com

If we fail to reconstruct the BIOS fb (e.g., because the FB is too
large), we'll be left with plane state that indicates the primary plane
is visible yet has a NULL fb.  This mismatch causes problems later on
(e.g., for the watermark code).  Since we've failed to reconstruct the
BIOS FB, the best solution is to just disable the primary plane and
pretend the BIOS never had it enabled.

v2: Add intel_pre_disable_primary() call (Maarten)

Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449171462-30763-2-git-send-email-matthew.d.roper@intel.com

A long time ago (before 3.14) we relied on a permanent pinning of the
ifbdev to lock the fb in place inside the GGTT. However, the
introduction of stealing the BIOS framebuffer and reusing its address in
the GGTT for the fbdev has muddied waters and we use an inherited fb.
However, the inherited fb is only pinned whilst it is active and we no
longer have an explicit pin for the info->system_base mmapping used by
the fbdev. The result is that after some aperture pressure the fbdev may
be evicted, but we continue to write the fbcon into the same GGTT
address - overwriting anything else that may be put into that offset.
The effect is most pronounced across suspend/resume as
intel_fbdev_set_suspend() does a full clear over the whole scanout.

v2: Only unpin the intel_fb is we allocate it. If we inherit the fb from
the BIOS, we do not own the pinned vma (except for the reference we add
in this patch for our access via info->screen_base).

v3: Finish balancing the vma pinning for the normal !preallocated case.

v4: Try to simplify the pinning even further.
v5: Leak the VMA (cleaned up by object-free) to avoid complicated error paths.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: "Goel, Akash" <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1449245126-26158-1-git-send-email-chris@chris-wilson.co.ukTested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As we mark the preallocated objects as bound, we should also flag them
correctly as being map-and-fenceable (if appropriate!) so that later
users do not get confused and try and rebind the pinned vma in order to
get a map-and-fenceable binding.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: "Goel, Akash" <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1448029000-10616-1-git-send-email-chris@chris-wilson.co.ukReviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I missed this myself when reviewing

commit 237ed86c
Author: Sonika Jindal <sonika.jindal@intel.com>
Date:   Tue Sep 15 09:44:20 2015 +0530

    drm/i915: Check live status before reading edid

Long sleeps like this really shouldn't waste cpu cycles spinning.

Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: "Wang, Gary C" <gary.c.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449859455-32609-1-git-send-email-daniel.vetter@ffwll.chReviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The device should be on for the whole duration of the update, so check
for this.

v2:
- use the existing dev_priv directly everywhere (Ville)
v3:
- check also that we are in an RPM atomic section (Chris)
- add the assert to i915_ggtt_insert_entries/clear_range too (Chris)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-11-git-send-email-imre.deak@intel.com

In some cases we want to check whether we hold an RPM wakelock reference
for the whole duration of a sequence. To achieve this add a new RPM
atomic sequence counter that we increment any time the wakelock refcount
drops to zero.  Check whether the sequence number stays the same during
the atomic section and that we hold the wakelock at the beginning of the
section.

Motivated by Chris.

v2-v3:
- unchanged
v4:
- swap the order of atomic_read() and assert_rpm_wakelock_held() in
  assert_rpm_atomic_begin() to avoid race
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-10-git-send-email-imre.deak@intel.com

With this change we have the corresponding wake lock checks in both the
rpm get and put functions.

v2-v3:
- unchanged
v4:
- keep the corresponding check in the get helper (Chris)
v5:
- add a note to the commit message that with this change we have the
  checks both in the rpm get and put functions (Joonas)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-9-git-send-email-imre.deak@intel.com

Atm, we assert that the device is not suspended until the point when the
device is truly put to a suspended state. This is fine, but we can catch
more problems if we check that RPM refcount is non-zero. After that one
drops to zero we shouldn't access the device any more, even if the actual
device suspend may be delayed. Change assert_rpm_wakelock_held()
accordingly to check for a non-zero RPM refcount in addition to the
current device-not-suspended check.

For the new asserts to work we need to annotate every place explicitly in
the code where we expect that the device is powered. The places where we
only assume this, but may not hold an RPM reference:
- driver load
  We assume the device to be powered until we enable RPM. Make this
  explicit by taking an RPM reference around the load function.
- system and runtime sudpend/resume handlers
  These handlers are called when the RPM reference becomes 0 and know the
  exact point after which the device can get powered off. Disable the
  RPM-reference-held check for their duration.
- the IRQ, hangcheck and RPS work handlers
  These handlers are flushed in the system/runtime suspend handler
  before the device is powered off, so it's guaranteed that they won't
  run while the device is powered off even though they don't hold any
  RPM reference. Disable the RPM-reference-held check for their duration.

In all these cases we still check that the device is not suspended.
These explicit annotations also have the positive side effect of
documenting our assumptions better.

This caught additional WARNs from the atomic modeset path, those should
be fixed separately.

v2:
- remove the redundant HAS_RUNTIME_PM check (moved to patch 1) (Ville)
v3:
- use a new dedicated RPM wakelock refcount to also catch cases where
  our own RPM get/put functions were not called (Chris)
- assert also that the new RPM wakelock refcount is 0 in the RPM
  suspend handler (Chris)
- change the assert error message to be more meaningful (Chris)
- prevent false assert errors and check that the RPM wakelock is 0 in
  the RPM resume handler too
- prevent false assert errors in the hangcheck work too
- add a device not suspended assert check to the hangcheck work
v4:
- rename disable/enable_rpm_asserts to disable/enable_rpm_wakeref_asserts
  and wakelock_count to wakeref_count
- disable the wakeref asserts in the IRQ handlers and RPS work too
- update/clarify commit message
v5:
- mark places we plan to change to use proper RPM refcounting with
  separate DISABLE/ENABLE_RPM_WAKEREF_ASSERTS aliases (Chris)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450227139-13471-1-git-send-email-imre.deak@intel.com

Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-7-git-send-email-imre.deak@intel.com

As a preparation for follow-up patches add a new helper that checks
whether we hold an RPM reference, since this is what we want most of
the cases. Atm this helper will only check for the HW suspended state, a
follow-up patch will do the actual change to check the refcount instead.
One exception is the forcewake release timer function, where it's
guaranteed that the HW is on even though the RPM refcount drops to zero.
This guarantee is provided by flushing the timer in the runtime suspend
handler. So leave the assert_device_not_suspended check in place there.

Also rename assert_device_suspended for consistency and export these
helpers as a preparation for the follow-up patches.

No functional change.

v3:
- change the assert warning message to be more meaningful (Chris)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-6-git-send-email-imre.deak@intel.com

We don't really need to check this flag in the get/put/assert helpers,
as on platforms without RPM support we won't ever enable RPM. That means
pm.suspend will be always false and the assert will be always true.

Do this to simplify the code and to let us extend the RPM asserts to all
platforms for a better coverage.

Motivated by Ville.

v2-v3:
- unchanged
v4:
- remove the HAS_RUNTIME_PM check from intel_runtime_pm_enable() too
  made possible by the previous two patches
v5:
- rebased on the previous new patch in the series that keeps
  HAS_RUNTIME_PM() in intel_runtime_pm_enable() with a permanent
  reference taken there
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450352931-16498-1-git-send-email-imre.deak@intel.com

Currently we disable RPM functionality on platforms that doesn't support
this by not putting/getting the RPM reference we receive from the RPM
core during driver loading/unloading respectively. This is somewhat
obscure, so make it more explicit by keeping a reference dedicated for
this particular purpose whenever the driver is loaded. This makes it
possible to remove the HAS_RUNTIME_PM() special casing from every other
places in the next patch.

v2:
- fix intel_runtime_pm_get vs. intel_runtime_pm_put in
  intel_power_domains_fini()
v3:
- take only a low level RPM reference so the ref tracking asserts
  continue to work (Ville)
- update the commit message
- move the patch earlier for bisectability
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450352696-16135-1-git-send-email-imre.deak@intel.com

We can make the RPM dependency on RC6 explcit in the code by taking an
actual RPM reference, instead of avoiding to drop the initial one. This
will also enable us to remove the HAS_RUNTIME_PM special casing from
more places in the next patch.

v2:
- fixed typo in commit message (Joonas)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-4-git-send-email-imre.deak@intel.com

Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-2-git-send-email-imre.deak@intel.com

The RVDA and RVDS (raw VBT data address and size) fields of the ASLE
mailbox may specify an alternate location for VBT instead of mailbox #4.
Use the alternate location if available and valid, falling back to
mailbox #4 otherwise.

v2: Update debug logging (Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NMika Kahola <mika.kahola@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178280-28020-1-git-send-email-jani.nikula@intel.com

I broke AVI/HDMI/SPD infoframes on HSW+ with the register type
safety changes. We were supposed to check that the infoframe data
register is valid before writing the infoframe data, but the check
ended up inverted, and so in practice we never wrote or enabled
these infoframes.

We were still sending out the GCP infoframe when the sink was
deep-color capable. That and the fact that we use a single
bool to track our infoframe state meant that the state checker
only caught this when a HDMI sink that doesn't do deep-color was
used.

We really need to fix our infoframe state checking to be much
more anal. But in the meantime let's just fix the regression.
In fact let's just throw out the register validity check and
convert some of the "unknown info frame type" debug messages
into MISSING_CASE(). So far we support the same set of infoframe
types on all platforms, so the silent debug messages make no
sense.

Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: f0f59a00 ("drm/i915: Type safe register read/write")
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (irc)
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (irc)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450282200-4203-1-git-send-email-ville.syrjala@linux.intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93119Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Slightly cleaner with early exit.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450271061-32646-4-git-send-email-jani.nikula@intel.com

dev_priv is the new black. Or something.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450271061-32646-3-git-send-email-jani.nikula@intel.com

Specify the maximum number of letters to print from the potentially
unterminated buffer, not the minimum. While at it, use sizeof instead of
a magic number.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450271061-32646-2-git-send-email-jani.nikula@intel.com

The intel_bios.h header doesn't even need it, but other headers included
from i915_drv.h do. Let's untangle the mess a bit.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450271061-32646-1-git-send-email-jani.nikula@intel.com

Use the for_each_intel_* macros for iterating intel_encoder,
intel_connector, and intel_crtc. No functional changes.
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450262896-5325-1-git-send-email-jani.nikula@intel.com

In the future the VBT might not be in mailbox #4 of the ACPI OpRegion,
thus unavailable in i915_opregion, so add a separate file for the VBT.

v2: Drop the locking as unneeded (Chris)
v3: Rebase

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178232-27780-1-git-send-email-jani.nikula@intel.com

Hasn't been necessary since

commit 115719fc
Author: Williams, Dan J <dan.j.williams@intel.com>
Date:   Mon Oct 12 21:12:57 2015 +0000

    i915: switch from acpi_os_ioremap to memremap
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/74664a556a56d0eceb0029bbd77ffc1d771b0628.1450089383.git.jani.nikula@intel.com

Because we can. It's not to be touched so tell the compiler too.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/4b1872b121fb34a193cff9a5cb4e7c858d4a55aa.1450089383.git.jani.nikula@intel.com

The VBT in OpRegion should fit in mailbox #4.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/4bdb3f5820e3dbd1cdfa7b65cadfce4f80b880f0.1450089383.git.jani.nikula@intel.com

Make the validation function a boolean operating on a buffer of given
size, removing the extra pointer dances.

Move the OpRegion based VBT validation to intel_opregion_setup(), only
initializing opregion->vbt if it's valid.

v2: move logging about valid VBT to opregion setup too (Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178175-27420-1-git-send-email-jani.nikula@intel.com

While at it, move the declaration to where everything else is declared.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/7d9d879603038889f0128cf7cbbd9f591edc11dd.1450089383.git.jani.nikula@intel.com

The decision about which source will be used for VBT is done in
intel_parse_bios(), not in the VBT validation function. Make the VBT
validation function strictly about validation, and move the debug
logging to where it logically belongs.

Also split the logging about where the valid VBT was found and what the
signature is. This will make even more sense in the future when the
validation for ACPI OpRegion based VBT takes place at OpRegion setup
time.

v2: Split logging about VBT signature and BDB version.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178092-27148-1-git-send-email-jani.nikula@intel.com

This will simplify further work.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/d2c5210402fdd8c277e1d50892b0620d10c50ae8.1450089383.git.jani.nikula@intel.com

Check the quirk in intel_opregion_setup(), and don't initialize
opregion->vbt at all if the quirk says it's not present, hiding the
quirk from the rest of the driver.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/7cdc86eb441f8b7075142445a800b07ecf8c76cb.1450089383.git.jani.nikula@intel.com

Mailbox 5 is BIOS to Driver Notification mailbox is intended
to support BIOS to Driver event notification or data storage
for BIOS to Driver data synchronization purpose. Mailbox 5 is
the extension of mailbox 3.

v4 by Jani:
 - don't add asle_ext to dev_priv as it's unused
 - use u8 for bddc and rsvd fields in asle ext struct
 - add BUILD_BUG_ON the asle ext struct size
 - debug logging for asle ext present

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NDeepak M <m.deepak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/c2d4009659fca32280d9859ec34a62f45b86d895.1450089383.git.jani.nikula@intel.com

The cursor code tries to treat base==0 to mean disabled. That fails
when the cursor bo gets bound at ggtt offset 0, and the user is left
looking at an invisible cursor.

We lose the disabled->disabled optimization, but that seems like
something better handled at a slightly higher level.

Cc: drm-intel-fixes@lists.freedesktop.org
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450091808-32607-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

The vma may have been rebound between the last time the cursor was
enabled and now, so skipping the cursor gtt offset deduction is not
safe unless we would also reset cursor_bo to NULL when disabling the
cursor. Just thow cursor_bo to the bin instead since it's lost all
other uses thanks to universal plane support.

Chris pointed out that cursor updates are currently too slow
via universal planes that micro optimizations like these wouldn't
even help.

v2: Add a note about futility of micro optimizations (Chris)

Cc: drm-intel-fixes@lists.freedesktop.org
References: http://lists.freedesktop.org/archives/intel-gfx/2015-December/082976.html
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450107302-17171-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

This bit is also reserved on Skylake. Actually the only
platform that supports this is Haswell, so let's fix
this logic and apply this link entry time only for the
platform that supports it, i.e. Haswell.

This also changes the style to let more clear platform
differences outside the reg write. We would probably catch
this case sooner if separated, or not...
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449880291-21388-1-git-send-email-rodrigo.vivi@intel.com

Add get_eld audio component for i915/HD-audio

Currently, the HDMI/DP audio status and ELD are notified and obtained
via the hardware-level communication over HD-audio unsolicited event
and verbs although the graphics driver holds the exactly same
information.  As we already have a notification via audio component,
this is another step forward; namely, the audio driver may fetch
directly the audio status and ELD via the new component op.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

When creating a new (pageable) GEM object and filling it with data, we
must mark it as 'dirty', i.e. backing store is out-of-date w.r.t. the
newly-written content. This ensures that if the object is evicted under
memory pressure, its pages in the pagecache will be written to backing
store rather than discarded.

Based on an original version by Alex Dai.
Signed-off-by: NAlex Dai <yu.dai@intel.com>
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1449773486-30822-3-git-send-email-david.s.gordon@intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In various places, a single page of a (regular) GEM object is mapped into
CPU address space and updated. In each such case, either the page or the
the object should be marked dirty, to ensure that the modifications are
not discarded if the object is evicted under memory pressure.

The typical sequence is:
	va = kmap_atomic(i915_gem_object_get_page(obj, pageno));
	*(va+offset) = ...
	kunmap_atomic(va);

Here we introduce i915_gem_object_get_dirty_page(), which performs the
same operation as i915_gem_object_get_page() but with the side-effect
of marking the returned page dirty in the pagecache.  This will ensure
that if the object is subsequently evicted (due to memory pressure),
the changes are written to backing store rather than discarded.

Note that it works only for regular (shmfs-backed) GEM objects, but (at
least for now) those are the only ones that are updated in this way --
the objects in question are contexts and batchbuffers, which are always
shmfs-backed.

Separate patches deal with the cases where whole objects are (or may
be) dirtied.

v3: Mark two more pages dirty in the page-boundary-crossing
    cases of the execbuffer relocation code [Chris Wilson]
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1449773486-30822-2-git-send-email-david.s.gordon@intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When clearing an execlist queue, instead of traversing it and unreferencing all
requests while holding the spinlock (which might lead to thread sleeping with
IRQs are turned off - bad news!), just move all requests to the retire request
list while holding spinlock and then drop spinlock and invoke the execlists
request retirement path, which already deals with the intricacies of
purging/dereferencing execlist queue requests.

This patch can be considered v3 of:

	commit b96db8b81c54ef30485ddb5992d63305d86ea8d3
	Author: Tomas Elf <tomas.elf@intel.com>
	drm/i915: Grab execlist spinlock to avoid post-reset concurrency issues

This patch assumes v2 of the above patch is part of the baseline, reverts v2
and adds changes on top to turn it into v3.
Signed-off-by: NTomas Elf <tomas.elf@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1445619757-19822-1-git-send-email-tomas.elf@intel.comReviewed-by: NThomas Daniel <thomas.daniel@intel.com>
Reviewed-by: NDave Gordon <dave.gordon@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>