Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 161
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 24 9月, 2015 1 次提交
  3. 22 9月, 2015 20 次提交
  5. 19 9月, 2015 1 次提交
  7. 18 9月, 2015 1 次提交
  9. 17 9月, 2015 1 次提交
  11. 16 9月, 2015 1 次提交
  13. 15 9月, 2015 3 次提交
    • N
      Documentation: bindings: add doc for zynq USB · c1ceb5ff
      由 Nathan Sullivan 提交于 
      Document the binding for the zynq specific chipidea UDC binding.
Signed-off-by: NNathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
      c1ceb5ff
    • N
      usb: chipidea: add xilinx zynq platform data · 84bc70f9
      由 Nathan Sullivan 提交于 
      Due to having hardware tx buffers less than 512 bytes in size, streaming
must be enabled on the Zynq for the udc to work at all.  Add platform data
specific to the Zynq udc, which does not set the CI_HDRC_DISABLE_STREAMING
flag.

Based on a patch by the same name from the Xilinx vendor tree.
Signed-off-by: NNathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
      84bc70f9
    • P
      usb: chipidea: udc: using the correct stall implementation · 56ffa1d1
      由 Peter Chen 提交于 
      According to spec, there are functional and protocol stalls.

For functional stall, it is for bulk and interrupt endpoints,
below are cases for it:
- Host sends SET_FEATURE request for Set-Halt, the udc driver
needs to set stall, and return true unconditionally.
- The gadget driver may call usb_ep_set_halt to stall certain
endpoints, if there is a transfer in pending, the udc driver
should not set stall, and return -EAGAIN accordingly.
These two kinds of stall need to be cleared by host using CLEAR_FEATURE
request (Clear-Halt).

For protocol stall, it is for control endpoint, this stall will
be set if the control request has failed. This stall will be
cleared by next setup request (hardware will do it).

It fixed usbtest (drivers/usb/misc/usbtest.c) Test 13 "set/clear halt"
test failure, meanwhile, this change has been verified by
USB2 CV Compliance Test and MSC Tests.

Cc: <stable@vger.kernel.org> #3.10+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
      56ffa1d1
  15. 14 9月, 2015 9 次提交
  17. 13 9月, 2015 3 次提交
    • L
      Linux 4.3-rc1 · 6ff33f39
      由 Linus Torvalds 提交于
      6ff33f39
    • L
      Merge tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris · 6917b51d
      由 Linus Torvalds 提交于 
      Pull CRIS updates from Jesper Nilsson:
 "Mostly removal of old cruft of which we can use a generic version, or
  fixes for code not commonly run in the cris port, but also additions
  to enable some good debug"

* tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris: (25 commits)
  CRISv10: delete unused lib/dmacopy.c
  CRISv10: delete unused lib/old_checksum.c
  CRIS: fix switch_mm() lockdep splat
  CRISv32: enable LOCKDEP_SUPPORT
  CRIS: add STACKTRACE_SUPPORT
  CRISv32: annotate irq enable in idle loop
  CRISv32: add support for irqflags tracing
  CRIS: UAPI: use generic types.h
  CRIS: UAPI: use generic shmbuf.h
  CRIS: UAPI: use generic msgbuf.h
  CRIS: UAPI: use generic socket.h
  CRIS: UAPI: use generic sembuf.h
  CRIS: UAPI: use generic sockios.h
  CRIS: UAPI: use generic auxvec.h
  CRIS: UAPI: use generic headers via Kbuild
  CRIS: UAPI: fix elf.h export
  CRIS: don't make asm/elf.h depend on asm/user.h
  CRIS: UAPI: fix ptrace.h
  CRISv32: Squash compile warnings for axisflashmap
  CRISv32: Add GPIO driver to the default configs
  ...
      6917b51d
    • L
      blk: rq_data_dir() should not return a boolean · 10fbd36e
      由 Linus Torvalds 提交于 
      rq_data_dir() returns either READ or WRITE (0 == READ, 1 == WRITE), not
a boolean value.

Now, admittedly the "!= 0" doesn't really change the value (0 stays as
zero, 1 stays as one), but it's not only redundant, it confuses gcc, and
causes gcc to warn about the construct

    switch (rq_data_dir(req)) {
        case READ:
            ...
        case WRITE:
            ...

that we have in a few drivers.

Now, the gcc warning is silly and stupid (it seems to warn not about the
switch value having a different type from the case statements, but about
_any_ boolean switch value), but in this case the code itself is silly
and stupid too, so let's just change it, and get rid of warnings like
this:

  drivers/block/hd.c: In function ‘hd_request’:
  drivers/block/hd.c:630:11: warning: switch condition has boolean value [-Wswitch-bool]
     switch (rq_data_dir(req)) {

The odd '!= 0' came in when "cmd_flags" got turned into a "u64" in
commit 5953316d ("block: make rq->cmd_flags be 64-bit") and is
presumably because the old code (that just did a logical 'and' with 1)
would then end up making the type of rq_data_dir() be u64 too.

But if we want to retain the old regular integer type, let's just cast
the result to 'int' rather than use that rather odd '!= 0'.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      10fbd36e