This network device driver shares the same hardware as the qla4xxx
iSCSI driver. Changing the MTU via the device interface will
cause qla4xxx to crash as there is no way to make notification.
Users wishing to change the MTU must do so using an iSCSI
utility such as Qlogic SanSurfer. This forces the user to
unload/reload this network device driver after the MTU
value has been changed in flash.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

1) Fix deadlock issue when in QL_RESET_ACTIVE state and traversing
   through the Link State Machine
2) Fix deadlock issue when ethtool would call ql_get_settings()
3) Fix deadlock issue when adaptor is ifup'ed but adaptor fails to initialize
Signed-off-by: NBenjamin Li <benjamin.li@qlogic.com>
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NBenjamin Li <benjamin.li@qlogic.com>
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We do not need to zero out the 64 byte MAC request I/O control block.
  By zeroing out the control block and setting it to proper fields is
redundant work.  This is because in the qla3xxx_send() function we will
already set the proper fields in this structure.  The unused fields are
not looked at by the hardware and do not need to be zeroed out.
Signed-off-by: NBenjamin Li <benjamin.li@qlogic.com>
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The return code was not properly set when when allocating memory or mapping
memory failed.  Depending on the stack, the return code would sometimes
return 0, which indicates everything was ok, when in fact there was an error.
  This would cause trouble when the module was removed.  Now, we will pass
back the proper return code when an error occurs during the PCI probe.
Signed-off-by: NBenjamin Li <benjamin.li@qlogic.com>
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver contains this little piece of candy:

#if defined(CONFIG_DMA_NONCOHERENT) || defined(CONFIG_NOT_COHERENT_CACHE)
#define ETH_DMA_ALIGN           L1_CACHE_BYTES
#else
#define ETH_DMA_ALIGN           8
#endif

Any reason why we're not using dma_get_cache_alignment() instead?

  Ralf
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update ucc_geth_probe() to use function of_get_mac_address() to obtain the MAC
address.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use comma's consistently.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It looks like the skge driver inherited another bug from the sk98lin code.
If I send from 1000mbit port to a machine on 100mbit port, the switch should
be doing hardware flow control, but no pause frames show up in the statistics.

This is the analog of the recent sky2 fixes. The device needs to listen
for multicast pause frames and then not discard them.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Work around a bug which occurs when adopting firmware versions
1.4.4 though 1.4.11 where broadcasts are filtered as if they
were multicasts.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAmit S. Kale <amitkale@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAmit S. Kale <amitkale@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Janitorial patch. Undo long lines, fix typo in err msg.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Multiple threads performing a transmit can race into
the spidernet tx ring cleanup code. This puts the
relevant check under a lock.
Signed-off-by: NLinas Vepstas <lins@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It appears that under certain circumstances, a race will result
in a double-free of an skb. This patch null's out the skb pointer
upon the skb free, avoiding the inadvertent deref of bogus data.
The next patch fixes the actual race.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch separates the hardware descriptor state from the
driver descriptor state, per (old) suggestion from Ben Herrenschmidt.
This compiles and boots and seems to work.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This moves the medium variable into the spidernet card structure.
It renames the GMII_ variables to BCM54XX specific ones.
Signed-off-by: NJens Osterkamp <jens@de.ibm.com>
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patches removes logging for SPIDER_NET_GTMFLLINT interrupts.
Since the interrupts are not irregular, and they happen frequently
when using 100Mbps network switches.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds or changes some HW specific settings for spider_net on
Celleb.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch moves calling init_firmware() from spider_net_probe() to
spider_net_open() so as to use the driver by built-in.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add auto negotiation support for Celleb.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As of 2.6.20-git4, the spider_net driver does not compile.
This appears to be due to some archaic usage involving kobjects.

It also fixes a nasty double-free during ifdown of the interface.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This version moves the medium variable to the card specific structure and
changes the GMII_* to BCM54XX_* #defines.

This patch adds improved version of enable_fiber for both the 5421 and
the 5461 phy. It is now possible to specify with these wether you want
autonegotiation or not. This is needed for bladecenter switches where
some expect autonegotiation and some dont seem to like this at all.
Depending on this flag it sets phy->autoneg accordingly for the fiber mode.

More importantly it implements proper read_link and poll_link functions
for both phys which can handle both copper and fiber mode by determining
the medium first and then branching to the required functions. For fiber
they all work fine, for copper they are not tested but return the result
of the genmii_* function anyway which is supposed to work.

The patch moves the genmii_* functions around to avoid foreward declarations.
Signed-off-by: NJens Osterkamp <jens@de.ibm.com>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch removes checksum offload feature in mcp65 chipsets as they
are not supported in hw.
Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There seems to be an issue when both MSI-X is enabled and NAPI is
configured. This patch disables MSI-X until the issue is root caused.
Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The napi poll routine was missing the call to the optimized rx process
routine. This patch adds the missing call for the optimized path.
Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* clear_page() use is wrong.  We might have multiple pages.
  Use memset() instead.
* Call pci_unregister_driver() in module exit.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

1.  Add race condition check after netif_stop_queue().  tg3_tx() runs
    without netif_tx_lock and can race with tg3_start_xmit_dma_bug() ->
    tg3_tso_bug().

2.  Firmware TSO in 5703/5704/5705 also have the same TSO limitation,
    i.e. they cannot handle TSO headers bigger than 80 bytes.  Rename
    TG3_FL2_HW_TSO_1_BUG to TG3_FL2_TSO_BUG and set this flag on
    these chips as well.

3.  Update version to 3.74.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit d2ed1635.

As Thomas Gleixner reports:
  "e1000 is not working anymore. ifup fails permanentely.
    ADDRCONF(NETDEV_UP): eth0: link is not ready
   nothing else"

The broken commit was identified with "git bisect".

Auke Kok says:
  "I think we need to drop this now.  The report that says that this
   *fixes* something might have been on regular interrupts only.  I
   currently suspect that it breaks all MSI interrupts, which would make
   sense if I look a the code.  Very bad indeed."

Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NAuke Kok <auke-jan.h.kok@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the use of CONFIG_MV643XX_ETH_[012] variables on most platforms.
Instead, platform-specific code enables the ports supported by the
hardware.  After this patch, these config variables are only used in
arch/ppc, so also move them from drivers/net/Kconfig to arch/ppc/Kconfig.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Acked-by: NJeff Garzik <jeff@garzik.org>
Cc: Paul Mackerras <paulus@samba.org>

Aculab E1/T1 PMXc cPCI carrier card cards present a natsemi on the cPCI
bus with an oversized EEPROM using a direct MII<->MII connection with no
PHY.  This patch adds a new device table entry supporting these cards.
Signed-Off-By: NMark Brown <broonie@sirena.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch provides code paths which allow the natsemi driver to use the
external MII port on the chip but ignore any PHYs that may be attached to it.
The link state will be left as it was when the driver started and can be
configured via ethtool.  Any PHYs that are present can be accessed via the MII
ioctl()s.

This is useful for systems where the device is connected without a PHY
or where either information or actions outside the scope of the driver
are required in order to use the PHYs.
Signed-Off-By: NMark Brown <broonie@sirena.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If a workqueue function that needs RTNL is running when skge_down
is called then a deadlock is possible. Fix by only clearing the timer,
and handling the flush_scheduled_work on removal. This work queue is only
ever used for the old fiber based boards.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Mantra: don't use flush_scheduled_work with RTNL held.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Your usual dont-flush_scheduled_work-with-RTNL-held stuff.

It is a bit different here since the thread runs permanently
or is only occasionally kicked for recovery depending on the
hardware revision.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

flush_scheduled_work() in net_device->close has a slight tendency
to deadlock with tasks on the workqueue that hold RTNL.

rtl8169_close/down simply need the recovery tasks to not meddle
with the hardware while the device is going down.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

sk98lin is scheduled for removal in July 2007. This patch makes the
deprecation more obvious in the configuration interface. FWIW, Gentoo have
been shipping a patch very similar to this for a long time.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>