- 09 4月, 2013 4 次提交
-
-
由 Javier Martinez Canillas 提交于
ISEE IGEPv2 is an TI OMAP3 SoC based embedded board. This patch adds an initial device tree support to boot an IGEPv2 from the MMC/SD. Currently is working everything that is supported by DT on OMAP3 SoCs (MMC/SD, GPIO LEDs, EEPROM, TWL4030 audio). Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk> Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com> [benoit.cousson@linaro.org: Update the Makefile for 3.8-rc2] Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Javier Martinez Canillas 提交于
Add a generic .dtsi device tree source file for the common characteristics across IGEP Technology devices. Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: NMatthias Brugger <matthias.bgg@gmail.com> Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 AnilKumar Ch 提交于
Rename I2C and GPIO nodes according to AM33XX TRM. According to AM33XX TRM device instances are starting from "0" like i2c0, i2c1 and i2c3. Signed-off-by: NPantelis Antoniou <panto@antoniou-consulting.com> [panto@antoniou-consulting.com: initial patch by pantelis's] Signed-off-by: NAnilKumar Ch <anilkumar@ti.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Benoit Cousson 提交于
Merge tag 'omap-devel-b-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into for_3.10/dts_merged
-
- 03 4月, 2013 20 次提交
-
-
由 Roger Quadros 提交于
Provide RESET and Power regulators for the USB PHY, the USB Host port mode and the PHY device. Also provide pin multiplexer information for USB host pins. CC: Benoît Cousson <b-cousson@ti.com> Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Adds device nodes for HS USB Host module, TLL module, OHCI and EHCI controllers. CC: Benoît Cousson <b-cousson@ti.com> Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Adds device nodes for HS USB Host module, TLL module, OHCI and EHCI controllers. CC: Benoît Cousson <b-cousson@ti.com> Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulator and NOP PHY device. VAUX2 supplies the PHY's VCC. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. VAUX2 supplies the PHY's VCC. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Remove deprecated USBHS platform data. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's VCC and RESET regulators and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's VCC and RESET regulators and the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
Use usbhs_init_phys() to register the PHY's VCC and RESET regulators and the NOP PHY device. Get rid of managing the PHY clock as it will be done by the PHY driver. For that to work we create a clock alias that links the PHY clock name to the PHY device name. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
This helper allows board support code to add the PHY's VCC and RESET regulators which are GPIO controlled as well as the NOP PHY device. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 01 4月, 2013 10 次提交
-
-
由 Rajendra Nayak 提交于
omap3_noncore_dpll_set_rate() attempts an enable of bypass clk as well as ref clk for every .set_rate attempt on a noncore DPLL, regardless of whether the .set_rate results in the DPLL being locked or put in bypass. Early at boot, while some of these DPLLs are programmed and locked (using .set_rate for the DPLL), this causes an ordering issue. For instance, on OMAP5, the USB DPLL derives its bypass clk from ABE DPLL. If a .set_rate of USB DPLL which programmes the M,N and locks it is called before the one for ABE, the enable of USB bypass clk (derived from ABE DPLL) then attempts to lock the ABE DPLL and fails as the M,N values for ABE are yet to be programmed. To get rid of this ordering needs, enable bypass clk for a DPLL as part of its .set_rate only when its being put in bypass, and only enable the ref clk when its locked. Reported-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NRajendra Nayak <rnayak@ti.com> Signed-off-by: NPaul Walmsley <paul@pwsan.com>
-
由 Paul Walmsley 提交于
_pwrdm_save_clkdm_state_and_activate() tried to test one of its unsigned arguments to determine whether it was less than zero. Fix by moving the error test to the caller. Reported-by: NChen Gang <gang.chen@asianux.com> Signed-off-by: NPaul Walmsley <paul@pwsan.com>
-
由 Rajendra Nayak 提交于
_HWMOD_WAKEUP_ENABLED is currently unused across the hwmod framework. Just get rid of it, so we have one less flag to worry about. Tested-by: NVaibhav Bedia <vaibhav.bedia@ti.com> Signed-off-by: NRajendra Nayak <rnayak@ti.com> Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: NPaul Walmsley <paul@pwsan.com>
-
由 Vaibhav Hiremath 提交于
WDT1 module can take one of the below clocks as input functional clock - - On-Chip 32K RC Osc [default/reset] - 32K from PRCM The On-Chip 32K RC Osc clock is not an accurate clock-source as per the design/spec, so as a result, for example, timer which supposed to get expired @60Sec, but will expire somewhere ~@40Sec, which is not expected by any use-case. The solution here is to switch the input clock-source to PRCM generated 32K clock-source during boot-time itself. Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Benoit Cousson <benoit.cousson@linaro.org> Cc: Paul Walmsley <paul@pwsan.com>
-
由 Vaibhav Hiremath 提交于
This patch adds sysc definitions to the wdt1 hwmod entry, which in-turn makes sure that sysc idle bit-fields are configured to valid state on enable/disable callbacks. With the recent submitted patch from Santosh Shilimkar, "ARM: OMAP2+: hwmod: Don't call _init_mpu_rt_base if no sysc" (commit: 4a98c2d89), it is required to add sysconf information to each valid hwmod entry, else device will not be come out from idle state properly and leads to below kernel crash - [2.190237] Unhandled fault: external abort on non-linefetch (0x1028) at 0xf9e35034 [2.198325] Internal error: : 1028 [#1] SMP ARM [2.203101] Modules linked in: [2.206334] CPU: 0 Not tainted (3.9.0-rc3-00059-gd114294#1) [2.212679] PC is at omap_wdt_disable.clone.5+0xc/0x60 [2.218090] LR is at omap_wdt_probe+0x184/0x1fc Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Benoit Cousson <benoit.cousson@linaro.org> Cc: Paul Walmsley <paul@pwsan.com>
-
由 Linus Torvalds 提交于
-
git://git.infradead.org/users/vkoul/slave-dma由 Linus Torvalds 提交于
Pull slave-dmaengine fixes from Vinod Koul: "Two fixes for slave-dmaengine. The first one is for making slave_id value correct for dw_dmac and the other one fixes the endieness in DT parsing" * 'fixes' of git://git.infradead.org/users/vkoul/slave-dma: dw_dmac: adjust slave_id accordingly to request line base dmaengine: dw_dma: fix endianess for DT xlate function
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media由 Linus Torvalds 提交于
Pull media fixes from Mauro Carvalho Chehab: "For a some fixes for Kernel 3.9: - subsystem build fix when VIDEO_DEV=y, VIDEO_V4L2=m and I2C=m - compilation fix for arm multiarch preventing IR_RX51 to be selected - regression fix at bttv crop logic - s5p-mfc/m5mols/exynos: a few fixes for cameras on exynos hardware" * 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: [media] [REGRESSION] bt8xx: Fix too large height in cropcap [media] fix compilation with both V4L2 and I2C as 'm' [media] m5mols: Fix bug in stream on handler [media] s5p-fimc: Do not attempt to disable not enabled media pipeline [media] s5p-mfc: Fix encoder control 15 issue [media] s5p-mfc: Fix frame skip bug [media] s5p-fimc: send valid m2m ctx to fimc_m2m_job_finish [media] exynos-gsc: send valid m2m ctx to gsc_m2m_job_finish [media] fimc-lite: Fix the variable type to avoid possible crash [media] fimc-lite: Initialize 'step' field in fimc_lite_ctrl structure [media] ir: IR_RX51 only works on OMAP2
-
git://git.kernel.dk/linux-block由 Linus Torvalds 提交于
Pull block fixes from Jens Axboe: "Alright, this time from 10K up in the air. Collection of fixes that have been queued up since the merge window opened, hence postponed until later in the cycle. The pull request contains: - A bunch of fixes for the xen blk front/back driver. - A round of fixes for the new IBM RamSan driver, fixing various nasty issues. - Fixes for multiple drives from Wei Yongjun, bad handling of return values and wrong pointer math. - A fix for loop properly killing partitions when being detached." * tag 'for-linus-20130331' of git://git.kernel.dk/linux-block: (25 commits) mg_disk: fix error return code in mg_probe() rsxx: remove unused variable rsxx: enable error return of rsxx_eeh_save_issued_dmas() block: removes dynamic allocation on stack Block: blk-flush: Fixed indent code style cciss: fix invalid use of sizeof in cciss_find_cfgtables() loop: cleanup partitions when detaching loop device loop: fix error return code in loop_add() mtip32xx: fix error return code in mtip_pci_probe() xen-blkfront: remove frame list from blk_shadow xen-blkfront: pre-allocate pages for requests xen-blkback: don't store dev_bus_addr xen-blkfront: switch from llist to list xen-blkback: fix foreach_grant_safe to handle empty lists xen-blkfront: replace kmalloc and then memcpy with kmemdup xen-blkback: fix dispatch_rw_block_io() error path rsxx: fix missing unlock on error return in rsxx_eeh_remap_dmas() Adding in EEH support to the IBM FlashSystem 70/80 device driver block: IBM RamSan 70/80 error message bug fix. block: IBM RamSan 70/80 branding changes. ...
-
由 Paul Walmsley 提交于
This reverts commit 6aa97070. Commit 6aa97070 ("lockdep: check that no locks held at freeze time") causes problems with NFS root filesystems. The failures were noticed on OMAP2 and 3 boards during kernel init: [ BUG: swapper/0/1 still has locks held! ] 3.9.0-rc3-00344-ga937536b #1 Not tainted ------------------------------------- 1 lock held by swapper/0/1: #0: (&type->s_umount_key#13/1){+.+.+.}, at: [<c011e84c>] sget+0x248/0x574 stack backtrace: rpc_wait_bit_killable __wait_on_bit out_of_line_wait_on_bit __rpc_execute rpc_run_task rpc_call_sync nfs_proc_get_root nfs_get_root nfs_fs_mount_common nfs_try_mount nfs_fs_mount mount_fs vfs_kern_mount do_mount sys_mount do_mount_root mount_root prepare_namespace kernel_init_freeable kernel_init Although the rootfs mounts, the system is unstable. Here's a transcript from a PM test: http://www.pwsan.com/omap/testlogs/test_v3.9-rc3/20130317194234/pm/37xxevm/37xxevm_log.txt Here's what the test log should look like: http://www.pwsan.com/omap/testlogs/test_v3.8/20130218214403/pm/37xxevm/37xxevm_log.txt Mailing list discussion is here: http://lkml.org/lkml/2013/3/4/221 Deal with this for v3.9 by reverting the problem commit, until folks can figure out the right long-term course of action. Signed-off-by: NPaul Walmsley <paul@pwsan.com> Cc: Mandeep Singh Baines <msb@chromium.org> Cc: Jeff Layton <jlayton@redhat.com> Cc: Shawn Guo <shawn.guo@linaro.org> Cc: <maciej.rutecki@gmail.com> Cc: Fengguang Wu <fengguang.wu@intel.com> Cc: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ben Chan <benchan@chromium.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Tejun Heo <tj@kernel.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 31 3月, 2013 1 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending由 Linus Torvalds 提交于
Pull SCSI target fixes from Nicholas Bellinger: "This includes the bug-fix for a >= v3.8-rc1 regression specific to iscsi-target persistent reservation conflict handling (CC'ed to stable), and a tcm_vhost patch to drop VIRTIO_RING_F_EVENT_IDX usage so that in-flight qemu vhost-scsi-pci device code can detect the proper vhost feature bits. Also, there are two more tcm_vhost patches still being discussed by MST and Asias for v3.9 that will be required for the in-flight qemu vhost-scsi-pci device patch to function properly, and that should (hopefully) be the last target fixes for this round." * git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
-
- 30 3月, 2013 5 次提交
-
-
由 Andy Shevchenko 提交于
On some hardware configurations we have got the request line with the offset. The patch introduces convert_slave_id() helper for that cases. The request line base is came from the driver data provided by the platform_device_id table. Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: NViresh Kumar <viresh.kumar@linaro.org> Signed-off-by: NVinod Koul <vinod.koul@intel.com>
-
由 Arnd Bergmann 提交于
As reported by Wu Fengguang's build robot tracking sparse warnings, the dma_spec arguments in the dw_dma_xlate are already byte swapped on little-endian platforms and must not get swapped again. This code is currently not used anywhere, but will be used in Linux 3.10 when the ARM SPEAr platform starts using the generic DMA DT binding. Signed-off-by: NArnd Bergmann <arnd@arndb.de> Reported-by: NFengguang Wu <fengguang.wu@intel.com> Acked-by: NViresh Kumar <viresh.kumar@linaro.org> Signed-off-by: NVinod Koul <vinod.koul@intel.com>
-
由 Rafael J. Wysocki 提交于
The Adam Belay's e-mail address in MAINTAINERS under PNP SUPPORT is not valid any more and I started to maintain that code in the meantime as a matter of fact, so list myself as a maintainer of it along with Bjorn and remove the Adam's entry from it. Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client由 Linus Torvalds 提交于
Pull ceph fix from Sage Weil: "This fixes a regression introduced during the last merge window when mapping non-existent images." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: rbd: don't zero-fill non-image object requests
-
由 Alex Elder 提交于
A result of ENOENT from a read request for an object that's part of an rbd image indicates that there is a hole in that portion of the image. Similarly, a short read for such an object indicates that the remainder of the read should be interpreted a full read with zeros filling out the end of the request. This behavior is not correct for objects that are not backing rbd image data. Currently rbd_img_obj_request_callback() assumes it should be done for all objects. Change rbd_img_obj_request_callback() so it only does this zeroing for image objects. Encapsulate that special handling in its own function. Add an assertion that the image object request is a bio request, since we assume that (and we currently don't support any other types). This resolves a problem identified here: http://tracker.ceph.com/issues/4559 The regression was introduced by bf0d5f50. Reported-by: NDan van der Ster <dan@vanderster.com> Signed-off-by: NAlex Elder <elder@inktank.com> Reviewed-off-by: NSage Weil <sage@inktank.com>
-