The HP touchsmart tablet has a key for rotating the UI from landscape to
portrait. Add support for it.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

The Latitude C640 has another variation of dell in its DMI vendor entry.
Add it to the whitelist in order to enjoy the sweet fruits of software
backlight toggling.
Signed-off-by: NErik Andren <erik.andren@gmail.com>

Instead of a MODULE_DEVICE_TABLE for every acpi_driver ids table, we
create a table containing all ids to export to get a module alias for
each one.

This will fix automatic loading of the driver when one of the ACPI
devices is not present (like the accelerometer, which is not present in
some models).
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>

Right now, we assume that the hardware rfkill switch on Dells toggles all
radio devices. In fact, this can be configured in the BIOS and so right
now we may mark a device as hardware killed even when it isn't. Add code
to query the devices controlled by the switch, and use this when
determining the hardware kill state of a radio.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Calls to communicate with system firmware via a SMI (using dcdbas)
need to use a buffer that has a physical address of 4GB or less.
Currently the dell-laptop driver does not guarantee this, and when the
buffer address is higher than 4GB, the address is truncated to 32 bits
and the SMI handler writes to the wrong memory address.
Signed-off-by: NStuart Hayes <stuart_hayes@dell.com>
Acked-by: NMatthew Garrett <mjg@redhat.com>

The Mini family doesn't support smbios 17,11 although it reports it does.
Signed-off-by: NMario Limonciello <superm1@ubuntu.com>
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>

The "hardware" switch is tied directly to a BIOS interface that will
connect and disconnect the hardware from the bus.

If you use the software interface to request the BIOS to make these
changes, the HW switch will be in an inconsistent state and LEDs may not
reflect the state of the HW.
Signed-off-by: NMario Limonciello <Mario_Limonciello@Dell.com>

da_tokens was not being freed by dell-laptop on unload. Fix that.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

dell-laptop currently fails to clean up its platform device correctly.
Make sure that it's unregistered.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

The rfkill interface on Dells only sends a notification that the switch
has been changed via the keyboard controller. Add a filter so we can
pick these notifications up and update the rfkill state appropriately.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

This drops the support for manually groking the files in sysfs
to turn on and off the WLAN and BT for Compal laptops in favor
of platform rfkill support.

It has been combined into a single patch to not introduce regressions
in the process of simply adding rfkill support
Signed-off-by: NMario Limonciello <Mario_Limonciello@Dell.com>
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

The following Dell laptops are known to have been manufacturer by Compal
and are supported by the compal-laptop platform driver
 - Mini 9
 - Mini 10
 - Mini 12
 - Mini 10v
 - Inspiron 11z
Signed-off-by: NMario Limonciello <Mario_Limonciello@Dell.com>
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

Many of the drivers/platform/x86 drivers have nothing to do with ACPI, so
it's kind of inappropriate for them to be stuck under the ACPI mailing
list. Add a new mailing list (platform-driver-x86@vger.kernel.org) and,
with Len's blessing, add myself as subsystem maintainer.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: Anisse Astier <anisse@astier.eu>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Daniel Oliveira Nascimento <don@syst.com.br>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Henrique de Moraes Holschuh <ibm-acpi@hmh.eng.br>
Cc: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Cc: Karol Kozimor <sziwan@users.sourceforge.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Peter Feuerer <peter@piie.net>
Cc: Sujith Thomas <sujith.thomas@intel.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>

If radix_tree_preload is failed in ima_inode_alloc, we don't need
radix_tree_preload_end because kernel is alread preempt enabled
Signed-off-by: NXiaotian Feng <dfeng@redhat.com>
Signed-off-by: NMimi Zohar <zohar@us.ibm.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  parisc: Set PCI CLS early in boot.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Fix broken sn2 build

Set the PCI CLS early in the boot process to prevent
device failures. In pcibios_set_master use the new
pci_cache_line_size instead of a hard-coded value.
Signed-off-by: NCarlos O'Donell <carlos@codesourcery.com>
Reviewed-by: NGrant Grundler <grundler@google.com>
Signed-off-by: NKyle McMartin <kyle@redhat.com>

* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Fix out_le32() macro
  microblaze: Fix cache loop function for cache range

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  Revert "block: improve queue_should_plug() by looking at IO depths"

Trailing semicolon causes compilation involving out_le32() to fail.
Signed-off-by: NSteven J. Magnani <steve@digidescorp.com>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

I create wrong asm code but none test shows that this part of code is wrong.
I am not convinces that were good idea to create asm optimized macros
for caches. The reason is that there is not optimization with previous code
that's why make sense to add old code and do some benchmarking which
functions are faster.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net: bug fix for vlan + gro issue
  tc35815: Remove a wrong netif_wake_queue() call which triggers BUG_ON
  cdc_ether: new PID for Ericsson C3607w to the whitelist (resubmit)
  IPv6: better document max_addresses parameter
  MAINTAINERS: update mv643xx_eth maintenance status
  e1000: Fix DMA mapping error handling on RX
  iwlwifi: sanity check before counting number of tfds can be free
  iwlwifi: error checking for number of tfds in queue
  iwlwifi: set HT flags after channel in rxon

Traffic (tcp) doesnot start on a vlan interface when gro is enabled.
Even the tcp handshake was not taking place.
This is because, the eth_type_trans call before the netif_receive_skb
in napi_gro_finish() resets the skb->dev to napi->dev from the previously
set vlan netdev interface. This causes the ip_route_input to drop the
incoming packet considering it as a packet coming from a martian source.

I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7.
With this fix, the traffic starts and the test runs fine on both vlan
and non-vlan interfaces.

CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: Be in TS_POLLING state during mwait based C-state entry
  ACPI: Fix regression where _PPC is not read at boot even when ignore_ppc=0
  acer-wmi: Respect current backlight level when loading

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/vmwgfx: Fix queries if no dma buffer thrashing is occuring.
  drm/nv50: fix vram ptes on IGPs to point at stolen system memory
  drm/nv50: fix instmem binding on IGPs to point at stolen system memory
  drm/nv50: improve vram page table construction
  drm/nv50: more efficient clearing of gpu page table entries
  drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
  drm/nouveau: Fix up pre-nv17 analog load detection.

Revert the change made to arch/ia64/sn/kernel/setup.c by commit
204fba4a as it breaks the build.

Fixing the build the b94b0808 way
breaks xpc because genksyms then fails to generate an CRC for
per_cpu____sn_cnodeid_to_nasid because of limitations in the
generic genksyms code.
Signed-off-by: NHedi Berriche <hedi@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The netif_wake_queue() is called correctly (i.e. only on !txfull
condition) from txdone routine.  So Unconditional call to the
netif_wake_queue() here is wrong.  This might cause calling of
start_xmit routine on txfull state and trigger BUG_ON.

This bug does not happen when NAPI disabled.  After txdone there
must be at least one free tx slot.  But with NAPI, this is not
true anymore and the BUG_ON can hits on heavy load.

In this driver NAPI was enabled on 2.6.33-rc1 so this is
regression from 2.6.32 kernel.
Reported-by: NRalf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new vid/pid to the cdc_ether whitelist.

Device added:
- Ericsson Mobile Broadband variant C3607w
Signed-off-by: NTorgny Johansson <torgny.johansson@gmail.com>

--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.htmlSigned-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Morton wrote:
>> >From ip-sysctl.txt file in kernel documentation I can see following description
>> for max_addresses:
>> max_addresses - INTEGER
>>         Number of maximum addresses per interface.  0 disables limitation.
>>         It is recommended not set too large value (or 0) because it would
>>         be too easy way to crash kernel to allow to create too much of
>>         autoconfigured addresses.
           ^^^^^^^^^^^^^^

>> If this parameter applies only for auto-configured IP addressed, please state
>> it more clearly in docs or rename the parameter to show that it refers to
>> auto-configuration.

It did mention autoconfigured in the text, but the below makes it more obvious.

More clearly document IPv6 max_addresses parameter.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I am no longer with Marvell.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check for error return from pci_map_single/pci_map_page and clean up.

With this and the previous patch the driver was able to handle a significant
percentage of errors (I set the fault injection rate to 10% and could still
download large files at a reasonable speed).
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit fb1e7538.

"Benjamin S." <sbenni@gmx.de> reports that the patch in question
causes a big drop in sequential throughput for him, dropping from
200MB/sec down to only 70MB/sec.

Needs to be investigated more fully, for now lets just revert the
offending commit.

Conflicts:

	include/linux/blkdev.h
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Intercept query commands and apply relocations to their guest pointers.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

* 'nouveau/for-airlied' of ../drm-nouveau-next:
  drm/nv50: fix vram ptes on IGPs to point at stolen system memory
  drm/nv50: fix instmem binding on IGPs to point at stolen system memory
  drm/nv50: improve vram page table construction
  drm/nv50: more efficient clearing of gpu page table entries
  drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
  drm/nouveau: Fix up pre-nv17 analog load detection.

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: BCM47xx: Fix 128MB RAM support
  MIPS: Highmem: Fix build error

Merge branch 'parisc/tracehook' of git://git.kernel.org/pub/scm/linux/kernel/git/frob/linux-2.6-roland

* 'parisc/tracehook' of git://git.kernel.org/pub/scm/linux/kernel/git/frob/linux-2.6-roland:
  Revert "parisc: HAVE_ARCH_TRACEHOOK"