Rather than incrementing the reference count for boot_on regulators
(which prevents them being disabled later on) simply force the
regulator to be enabled when applying the constraints. Previously
boot_on was essentially equivalent to always_on.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Implement the recently added voltage step listing API for the WM835x
DCDCs and LDOs. DCDCs can use values up to 0x66, LDOs can use the full
range of values in the mask. Both masks are the lower bits of the
register.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The VAUX4 voltage table scrolls onto a second page in many versions
of the TWL4030 family manuals.  This doesn't mean we should ignore
those values!  Some boards use the (fully supported) 2.8V setting.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Specifying voltage constraints is optional (and only needed if the
consumer is allowed to change the voltage) so don't complain unless
a voltage has been specified.

Also avoid surprises with a dangling else while we're here.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

All DCDCs and LDOs are identical.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Glue between MMC and regulator stacks ... verified with
some OMAP3 boards using adjustable and configured-as-fixed
regulators on several MMC controllers.

These calls are intended to be used by MMC host adapters
using at least one regulator per host.  Examples include
slots with regulators supporting multiple voltages and
ones using multiple voltage rails (e.g. DAT4..DAT7 using a
separate supply, or a split rail chip like certain SDIO
WLAN or eMMC solutions).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Update previously-posted twl4030 regulator driver to export
supported voltages to upper layers using a new mechanism.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Support most of the LDO regulators in the twl4030 family chips.
In the case of LDOs supporting MMC/SD, the voltage controls are
used; but in most other cases, the regulator framework is only
used to enable/disable a supplies, conserving power when a given
voltage rail is not needed.

The drivers/mfd/twl4030-core.c code already sets up the various
regulators according to board-specific configuration, and knows
that some chips don't provide the full set of voltage rails.

The omitted regulators are intended to be under hardware control,
such as during the hardware-mediated system powerup, powerdown,
and suspend states.  Unless/until software hooks are known to
be safe, they won't be exported here.

These regulators implement the new get_status() operation, but
can't realistically implement get_mode(); the status output is
effectively the result of a vote, with the relevant hardware
inputs not exposed.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Add kerneldoc for the new get_status() message.  Fix the existing
kerneldoc for that struct in two ways:

 (a) Syntax, making sure parameter descriptions immediately
     follow the one-line struct description and that the first
     blank lines is before any more expansive description;
 (b) Presentation for a few points, to highlight the fact that
     the previous "get" methods exist only to report the current
     configuration, not to display actual status.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Add a basic mechanism for regulators to report the discrete
voltages they support:  list_voltage() enumerates them using
selectors numbered from 0 to an upper bound.

Use those methods to force machine-level constraints into bounds.
(Example:  regulator supports 1.8V, 2.4V, 2.6V, 3.3V, and board
constraints for that rail are 2.0V to 3.6V ... so the range of
voltages is then 2.4V to 3.3V on this board.)

Export those voltages to the regulator consumer interface, so for
example regulator hooked up to an MMC/SD/SDIO slot can report the
actual voltage options available to cards connected there.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM835x regulators need a different register checking for force
mode on each DCDC. Previously the force mode status for DCDC1 was
checked.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This is useful when wishing to run in a fixed operating mode that isn't
the default.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Update the documentation to suggest the use of datasheet names for
the supplies requested by regulator consumers. Doing this makes it
easier to tie the design for a given platform up with the requirements
of the driver for a consumer.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Remove deceased email address and update to new address. Also update
website details in MAINTAINERS with correct page.
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Currently regulator_unregister does not clear regulator <--> consumer
mapping.
This patch introduces unset_regulator_supplies that clear the map.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Fix regulator/driver.h missing kernel-doc:

Warning(linux-next-20090120//include/linux/regulator/driver.h:108): No description found for parameter 'get_status'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
cc: Liam Girdwood <lrg@slimlogic.co.uk>
cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Commit 872ed3fe176833f7d43748eb88010da4bbd2f983 caused regulator drivers
to take the struct regulator_dev lock themselves which requires that the
struct be visible to them. Band aid this by making the struct visible.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

It's not exported.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This allows users to enable or disable support for these regulators at
build time as they can for other regulators rather than having platforms
force the regulators to be built in.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Previously it was not possible to do so, making it impossible for
machines to configure the driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Rather than having the regulator init data read from the platform_data
member of the struct device that is registered for the regulator make
the init data an explict argument passed in when registering. This
allows drivers to use the platform data for their own purposes if they
wish.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Regulator: Push lock out of _notifier_call_chain and into caller functions
(side effect of fixing deadlock in regulator_force_disable)
+ Add a voltage changed event.
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

On Thu, 15 Jan 2009 16:10:22 -0800
Andrew Morton <akpm@linux-foundation.org> wrote:

> On Wed, 14 Jan 2009 13:16:27 -0800
> David Brownell <david-b@pacbell.net> wrote:
>
> > From: David Brownell <dbrownell@users.sourceforge.net>
> >
> > Minor cleanup to the regulator set_mode sysfs support:
> > switch to sysfs_streq() in set_mode(), which is also
> > a code shrink.  Use the same strings that get_mode()
> > uses, shrinking data too.
> >
> > Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
> > ---
> >  drivers/regulator/virtual.c |    8 ++++----
> >  1 file changed, 4 insertions(+), 4 deletions(-)
> >
> > --- a/drivers/regulator/virtual.c
> > +++ b/drivers/regulator/virtual.c
> > @@ -226,13 +226,13 @@ static ssize_t set_mode(struct device *d
> >  	unsigned int mode;
> >  	int ret;
> >
> > -	if (strncmp(buf, "fast", strlen("fast")) == 0)
> > +	if (sysfs_streq(buf, "fast\n") == 0)
> >  		mode = REGULATOR_MODE_FAST;
> > -	else if (strncmp(buf, "normal", strlen("normal")) == 0)
> > +	else if (sysfs_streq(buf, "normal\n") == 0)
> >  		mode = REGULATOR_MODE_NORMAL;
> > -	else if (strncmp(buf, "idle", strlen("idle")) == 0)
> > +	else if (sysfs_streq(buf, "idle\n") == 0)
> >  		mode = REGULATOR_MODE_IDLE;
> > -	else if (strncmp(buf, "standby", strlen("standby")) == 0)
> > +	else if (sysfs_streq(buf, "standby\n") == 0)
> >  		mode = REGULATOR_MODE_STANDBY;
>
> we don't need the \n's, do we?

oh, it's for the string sharing.  Sneaky.

I wonder how many people will try to fix that up for us?
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Based on previous LKML discussions:

 * Update docs for regulator sysfs class attributes to highlight
   the fact that all current attributes are intended to be control
   inputs, including notably "state" and "opmode" which previously
   implied otherwise.

 * Define a new regulator driver get_status() method, which is the
   first method reporting regulator outputs instead of inputs.
   It can report on/off and error status; or instead of simply
   "on", report the actual operating mode.

For the moment, this is a sysfs-only interface, not accessible to
regulator clients.  Such clients can use the current notification
interfaces to detect errors, if the regulator reports them.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Minor cleanup to the regulator set_mode sysfs support:
switch to sysfs_streq() in set_mode(), which is also
a code shrink.  Use the same strings that get_mode()
uses, shrinking data too.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  wireless: remove duplicated .ndo_set_mac_address
  netfilter: xtables: fix IPv6 dependency in the cluster match
  tg3: Add GRO support.
  niu: Add GRO support.
  ucc_geth: Fix use-after-of_node_put() in ucc_geth_probe().
  gianfar: Fix use-after-of_node_put() in gfar_of_init().
  kernel: remove HIPQUAD()
  netpoll: store local and remote ip in net-endian
  netfilter: fix endian bug in conntrack printks
  dmascc: fix incomplete conversion to network_device_ops
  gso: Fix support for linear packets
  skbuff.h: fix missing kernel-doc
  ni5010: convert to net_device_ops

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix reset hangs on Niagara systems.
  cpumask: use mm_cpumask() wrapper: sparc
  cpumask: remove dangerous CPU_MASK_ALL_PTR, &CPU_MASK_ALL.: sparc
  cpumask: remove the now-obsoleted pcibus_to_cpumask(): sparc
  cpumask: remove cpu_coregroup_map: sparc
  cpumask: prepare for iterators to only go to nr_cpu_ids/nr_cpumask_bits.: sparc
  cpumask: prepare for iterators to only go to nr_cpu_ids/nr_cpumask_bits.: sparc64
  cpumask: Use accessors code.: sparc64
  cpumask: Use accessors code: sparc
  cpumask: arch_send_call_function_ipi_mask: sparc
  cpumask: Use smp_call_function_many(): sparc64

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-cpumask:
  oprofile: Thou shalt not call __exit functions from __init functions
  cpumask: remove the now-obsoleted pcibus_to_cpumask(): generic
  cpumask: remove cpumask_t from core
  cpumask: convert rcutorture.c
  cpumask: use new cpumask_ functions in core code.
  cpumask: remove references to struct irqaction's mask field.
  cpumask: use mm_cpumask() wrapper: kernel/fork.c
  cpumask: use set_cpu_active in init/main.c
  cpumask: remove node_to_first_cpu
  cpumask: fix seq_bitmap_*() functions.
  cpumask: remove dangerous CPU_MASK_ALL_PTR, &CPU_MASK_ALL

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest-and-virtio:
  lguest: barrier me harder
  lguest: use bool instead of int
  lguest: use KVM hypercalls
  lguest: wire up pte_update/pte_update_defer
  lguest: fix spurious BUG_ON() on invalid guest stack.
  virtio: more neatening of virtio_ring macros.
  virtio: fix BAD_RING, START_US and END_USE macros

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon: (fschmd) Add support for the FSC Hades IC
  hwmon: (fschmd) Add support for the FSC Syleus IC
  i2c-i801: Instantiate FSC hardware montioring chips
  dmi: Let dmi_walk() users pass private data
  hwmon: Define a standard interface for chassis intrusion detection
  Move the pcf8591 driver to hwmon
  hwmon: (w83627ehf) Only expose in6 or temp3 on the W83667HG
  hwmon: (w83627ehf) Add support for W83667HG
  hwmon: (w83627ehf) Invert fan pin variables logic
  hwmon: (hdaps) Fix Thinkpad X41 axis inversion
  hwmon: (hdaps) Allow inversion of separate axis
  hwmon: (ds1621) Clean up documentation
  hwmon: (ds1621) Avoid unneeded register access
  hwmon: (ds1621) Clean up register access
  hwmon: (ds1621) Reorder code statements

* 'locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (33 commits)
  lockdep: fix deadlock in lockdep_trace_alloc
  lockdep: annotate reclaim context (__GFP_NOFS), fix SLOB
  lockdep: annotate reclaim context (__GFP_NOFS), fix
  lockdep: build fix for !PROVE_LOCKING
  lockstat: warn about disabled lock debugging
  lockdep: use stringify.h
  lockdep: simplify check_prev_add_irq()
  lockdep: get_user_chars() redo
  lockdep: simplify get_user_chars()
  lockdep: add comments to mark_lock_irq()
  lockdep: remove macro usage from mark_held_locks()
  lockdep: fully reduce mark_lock_irq()
  lockdep: merge the !_READ mark_lock_irq() helpers
  lockdep: merge the _READ mark_lock_irq() helpers
  lockdep: simplify mark_lock_irq() helpers #3
  lockdep: further simplify mark_lock_irq() helpers
  lockdep: simplify the mark_lock_irq() helpers
  lockdep: split up mark_lock_irq()
  lockdep: generate usage strings
  lockdep: generate the state bit definitions
  ...

* 'proc-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/adobriyan/proc:
  Revert "proc: revert /proc/uptime to ->read_proc hook"
  proc 2/2: remove struct proc_dir_entry::owner
  proc 1/2: do PDE usecounting even for ->read_proc, ->write_proc
  proc: fix sparse warnings in pagemap_read()
  proc: move fs/proc/inode-alloc.txt comment into a source file

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PCI PM: Make pci_prepare_to_sleep() disable wake-up if needed
  radeonfb: Use __pci_complete_power_transition()
  PCI PM: Introduce __pci_[start|complete]_power_transition() (rev. 2)
  PCI PM: Restore config spaces of all devices during early resume
  PCI PM: Make pci_set_power_state() handle devices with no PM support
  PCI PM: Put devices into low power states during late suspend (rev. 2)
  PCI PM: Move pci_restore_standard_config to pci-driver.c
  PCI PM: Use pci_set_power_state during early resume
  PCI PM: Consistently use variable name "error" for pm call return values
  kexec: Change kexec jump code ordering
  PM: Change hibernation code ordering
  PM: Change suspend code ordering
  PM: Rework handling of interrupts during suspend-resume
  PM: Introduce functions for suspending and resuming device interrupts

Fix printk format warnings in dma-debug:

  lib/dma-debug.c:645: warning: format '%016llx' expects type 'long long unsigned int', but argument 6 has type 'dma_addr_t'
  lib/dma-debug.c:662: warning: format '%016llx' expects type 'long long unsigned int', but argument 6 has type 'dma_addr_t'
  lib/dma-debug.c:676: warning: format '%016llx' expects type 'long long unsigned int', but argument 6 has type 'dma_addr_t'
  lib/dma-debug.c:686: warning: format '%016llx' expects type 'long long unsigned int', but argument 6 has type 'dma_addr_t'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch ifdefs xattr_create when xattrs aren't enabled.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix this build error when REISERFS_FS_POSIX_ACL is not set:

  fs/reiserfs/inode.c: In function 'reiserfs_new_inode':
  fs/reiserfs/inode.c:1919: warning: passing argument 1 of 'reiserfs_inherit_default_acl' from incompatible pointer type
  fs/reiserfs/inode.c:1919: warning: passing argument 2 of 'reiserfs_inherit_default_acl' from incompatible pointer type
  fs/reiserfs/inode.c:1919: warning: passing argument 3 of 'reiserfs_inherit_default_acl' from incompatible pointer type
  fs/reiserfs/inode.c:1919: error: too many arguments to function 'reiserfs_inherit_default_acl'

due to a missing transaction-handle argument in the non-acl
compatibility function.
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Acked-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Heiko reported that we grab the graph lock with irqs enabled.

Fix this by providng the same wrapper as all other lockdep entry
functions have.
Reported-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <npiggin@suse.de>
LKML-Reference: <1237544000.24626.52.camel@twins>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This reverts commit 6c87df37.

proc files implemented through seq_file do pread(2) now.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>

Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.

We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.

But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.

->read_proc/->write_proc were just fixed to not require ->owner for
protection.

rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.

Removing ->owner will also make PDE smaller.

So, let's nuke it.

Kudos to Jeff Layton for reminding about this, let's say, oversight.

http://bugzilla.kernel.org/show_bug.cgi?id=12454Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>