->In act_open_rpl(), CPL_ERR_TCAM_FULL error handling branch, there is
no handling of the return value of send_fw_act_open_req().
->In send_fw_act_open_req(), there is no handling of return value of
c4iw_l2t_send(), which may cause a ep leak and won't notify upper layers
on connection establish failure.
->send_mpa_req() should act on the return from c4iw_l2t_send() and
return the error to the caller.
->In case of c4iw_l2t_send() failure in send_mpa_req(), returns without
starting the timer and not changing the ep state, which is further
handled by act_establish()
-> In act_establish()?if send_mpa_request's get_skb returns an error,
may cause an ep leak. So handle return value of send_mpa_req()
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

->Stop the ep timer after MPA negotiation so that the arp failures
during send_mpa_reply/reject will be handled by process_timeout() after
the ep timer expires.
->Added case MPA_REP_SENT in process_timeout().
->For MPA reject, c4iw_ep_disconnect tries to start an already started
timer, which leads to warning message "timer already started".
-> In case of mpa reject stop the timer and call send_mpa_reject().
-> Added new ep flag STOP_MPA_TIMER to tell fw4_ack() to stop the timer
only for send_mpa_reply(), which is set in c4iw_accept_cr().
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In case of incomplete mpa messages we should not stop timer as it
results in return with timeout for the next mpa message
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

-> On passive side of connection parent_ep referenced during connection
request has to be dereferenced during the passive accept failure.
-> As passive accept failure error handlinglogic runs in atomic context,
the parent ep is dereferenced by scheduling work request.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

- add EP_DISC_FAIL history bit
- add QP_REFED/DEREFED history bits
- Add functions to ref/deref the cm_id and add history bit for the same
- add CLOSE_CON_RPL history
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Use c4iw_ep_disconnect() instead.  This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.

This is the last user of abort_connection(), so remove it too.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In c4iw_ep_disconnect(), if we fail to initiate a close operation, then
move the qp to ERROR to disassociate the ep from the qp.  Failure to do
this will leak the ep resources.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Instead return whether the caller needs to disconnect. This is part of
getting rid of abort_connection() altogether so we properly clean up on
send_abort() failures.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Use c4iw_ep_disconnect() instead. This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Instead, have the caller, rx_data() handle the close/abort like
it does for process_mpa_request(). This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In rx_data(), with the ep in FPDU_MODE, refcnt=2, if we get unexpected
streaming data, we call c4iw_modify_rc_qp() and move the qp from
RTS -> TERMINATE.  In c4iw_modify_rc_qp(), if rdma_fini() returns
an error, the ep will be dereferenced (refcnt=1).  Then rx_data()
calls c4iw_ep_disconnect() which starts the close operation.
But if send_halfclose() fails in c4iw_ep_disconnect(), we  will call
release_ep_resources() derefing the ep which reduces the refcnt to 0 and
and frees the ep. However we still has the ep mutex at that point, so we
have a touch-after-free bug.  There is a similar issue where
peer_close() calls c4iw_ep_disconnect().

The solution is to add a reference to the ep in c4iw_ep_disconnect()
after acquiring  the mutex, and release it after releasing the mutex.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In c4iw_ep_disconnect(), if we start the ep timer to begin a close,
but send_halfclose() fails, we need to stop the timer and send a CLOSE
event up to the IWCM before releasing the resources. Otherwise, we can
crash when the ep timer fires if the ep is referencing a previous instance
of the device. This can happen as part of adapter reset/recovery, for
instance.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

If ARP fails before the CPL_PASS_ACCEPT_RPL is seen by hardware, the tid
will be stuck in SYN_PEND and never released.  So create an arp failure
handler specifically for this message to release the endpoint resources.

In pass_accept_rpl_arp_failure(), put the parent endpoint so it will
be freed when destroyed.  Also we don't need to call release_tid() here
because _c4iw_free_ep() calls cxgb4_remove_tid() which releases the
hwtid.

If we get an ABORT_REQ_RSS instead of a PASS_ESTABLISH (because the
peer's ACK to our SYN is never received), then put the parent as well
in peer_abort().

Treat accept_cr() failures just like arp failures: put the parent ep
and release the ep resources destroying the tid

The ARP failure handlers are called in an atomic context, so we need to
schedule some of the processing which might block.  Namely _c4iw_free_ep()
which needs a mutex.  So create a "special" CPL opcode and handler and
schedule it via sched() to be run by process_work() in a blockable context.

Also rework the active open arp failure handler to make use of
release_ep_resources().  This allows both the active and passive arp
failure handlers to use the same deferred cleanup function.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Now that most of the port mapper code been moved to iwcm, we can remove
it from iw_cxgb4.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This series provides support for iWARP applications to specify a TOS
value and have that map to a VLAN Priority for iw_cxgb4 iWARP connections.

In iw_cxgb4, when allocating an L2T entry, pass the skb_priority based
on the tos value in the cm_id. Also pass the correct tos value during
connection setup so the passive side gets the client's desired tos.
When sending the FLOWC work request to FW, if the egress device is
in a vlan, then use the vlan priority bits as the scheduling class.
This allows associating RDMA connections with scheduling classes to
provide traffic shaping per flow.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Don't log errors if a listening endpoint is going away when procesing a
PASS_ACCEPT_REQ message.  This can happen.  Change the error printk to
a PDBG() debug log entry
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This series provides support for iWARP applications to specify a TOS
value and have that map to a VLAN Priority for iw_cxgb4 iWARP connections.

In iw_cxgb4, when allocating an L2T entry, pass the skb_priority based
on the tos value in the cm_id. Also pass the correct tos value during
connection setup so the passive side gets the client's desired tos.
When sending the FLOWC work request to FW, if the egress device is
in a vlan, then use the vlan priority bits as the scheduling class.
This allows associating RDMA connections with scheduling classes to
provide traffic shaping per flow.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't log errors if a listening endpoint is going away when procesing a
PASS_ACCEPT_REQ message.  This can happen.  Change the error printk to
a PDBG() debug log entry
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The h/w is designed in such a way that, if you do anything IPv6
related, a valid clip entry must be there. So take clip reference
before creating IPv6 listening servers, and then if we fail to
create server, release the clip entry.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This patch fix multiple spelling typos found in
various part of kernel.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The ESTABLISHED event should have the peer's ord/ird so
swap the values in the event before the upcall.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When calculating the minimum ird in c4iw_accept_cr(), we need to always
have a value of at least 1 if the RTR message is a 0B read.  The code
was
incorrectly using ep->ord for this logic which was incorrectly adjusting
the ird and causing incorrect ord/ird negotiation when using MPAv2 to
negotiate these values.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This allows client ULPs to get the negotiated ord/ird which is useful
to avoid stalling the SQ due to exceeding the ORD.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In c4iw_create_listen(), if we're using listen filters, then bail out
of the busy loop if the device becomes fatally dead
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This fixes an if statement checking the return value of the function
get_lladdr for success in the function pick_local_ip6addrs to instead
of directly checking the return value of this call check the opposite
as get_lladdr returns zero for success which would incorrectly make
this if statement block not execute with the current if statement
check.
Signed-off-by: NNicholas Krause <xerofoify@gmail.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add support for ipv6 address handling clip api provided by lld
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This enables ORD/IRD negotiation and its about time to enable it by
default
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

For listening endpoints bound to the wildcard address, we need to pass
the wildcard address mapping to iwpm_get_remote_info() instead of the
mapped address of the new child connection.

Without this fix, and with iwarp port mapping enabled, each iw_cxgb4
connection that is spawned from a listening endpoint bound to the wildcard
address, will generate an annoying dmesg entry about failing to find
the remote address mapping info, and the connection state displayed in
debugfs under /sys/kernel/debug/iw_cxgb4/<pci-slot-no>/eps  will not have
the peer's address/port mapping info.  The connection still works though.

Fixes: 5b6b8fe6 ("RDMA/cxgb4: Report the actual address of the remote connecting peer")
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Reviewed-by: NTatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove these log messages in favor of per-endpoint counters as well as
device-global counters that can be inspected via debugfs.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Get the actual (non-mapped) ip/tcp address of the connecting peer from
the port mapper

Also setup the passive side endpoint to correctly display the actual
and mapped addresses for the new connection.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

- get_dma_mr() was using ~0UL which is should be ~0ULL.  This causes the
DMA MR to get setup incorrectly in hardware.

- wr_log_show() needed a 64b divide function div64_u64() instead of
  doing
division directly.

- fixed warnings about recasting a pointer to a u64
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Cleanup macros and register defines for consistency
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Cleanup all the MACROS that are defined in t4fw_ri_api.h and affected files
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanup all the MACROS that are defined in t4fw_ri_api.h and affected files
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

iw_cxgb4/cxgb4/cxgb4vf/cxgb4i/csiostor: Cleanup register defines/macros related to all other cpl messages

This patch cleanups all other macros/register define related to
CPL messages that are defined in t4_msg.h and the affected files
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleanups all macros/register define related to connection management
CPL messages that are defined in t4_msg.h and the affected files
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cxgb4_create_server() and cxgb4_create_server6() return NET_XMIT_*
values or a negative errno. iw_cxgb4 need to handle this correctly.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>