Moves the 3Com drivers into drivers/net/ethernet/3com/ and the necessary
Kconfig and Makefile changes.

Did not move the following drivers becuase they use a non-3Com
chipset: 3c503, 3c505, 3c507, 3c523 and 3c527

CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
CC: David Dillow <dave@thedillows.org>
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Alan Cox <alan@linux.intel.com>
CC: David Hinds <dahinds@users.sourceforge.net>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NDavid Dillow <dave@thedillows.org>

This is the initial patch to organize the drivers/net directory
structure and networking device driver config options.  This patch
does the following:
  - add drivers/net/ethernet/Kconfig
  - integrate the new files into the existing config
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The dp83640 buffers receive time stamps from special PHY status frames,
matching them to received PTP packets in a work queue. Because the timeout
for orphaned time stamps is so long and the buffer is so small, the driver
can drop time stamps under moderate PTP traffic.

This commit fixes the issue by decreasing the timeout to (at least) one
timer tick and increasing the buffer size.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After resetting the time, the PPS signals on the FIPER output channels
are incorrectly offset from the clock time, as can be readily verified
by a looping back the FIPER to the external time stamp input.

Despite its name, setting the "Fiper Realignment Disable" bit seems to
fix the problem, at least on the P2020.

Also, following the example code from the Freescale BSP, it is not really
necessary to disable and re-enable the timer in order to reprogram the
FIPER. (The documentation is rather unclear on this point. It seems that
writing to the alarm register also disables the FIPER.)
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Executing cmd 'rmmod rtl8150' does not return(if your device connects
to host), the root cause is tasklet_disable() causes tasklet_kill()
block, remove it from rtl8150_disconnect().
Signed-off-by: NHuajun Li <huajun.li.lee@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o To support vlan lro, driver need to program ip address in device.
o Same ip addresses need to be program after fw recovery, so sotre them
  in list.
o In case of vlan packet, include vlan header length while
calculating ip and tcp headers.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The LG-VL600 LTE USB modem supports IPv6, but uses and expects an IPv4
ethertype (0x800) for these packets instead of the standard 0x86dd.
This patch peeks at the IP version in the L3 header and sets the
ethertype appropriately for IPv6 packets.
Signed-off-by: NMark Kamichoff <prox@prolixium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using nanosleep() in an userspace application we get a ratelimit warning:

	NOHZ: local_softirq_pending 08

According to 481a8199 the problem is caused by
netif_rx() function. This patch replaces netif_rx() with netif_rx_ni() which
has to be used from process/softirq context.
Signed-off-by: NMatvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The define is only used one place, and it's at the end of a line so
the semi-colon doesn't affect anything.  But let's clean it up
anyway.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver supports Autoneg and at least MII. Tell the PHY
that to avoid any confusion in the PHY code.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- empty lines
- tabs / spaces
- ETHTOOL_GWOL _is_ defined
- useless cast from void *
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NJon Nelson <jnelson@jamponi.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=14076.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NJon Nelson <jnelson@jamponi.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For older FW versions, when a Mac address removed from Mac table,
we should set 0 for reference count for the corresponding Mac index.
Fixes a bug where removing Mac from the table still left that entry as
invalid.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Tested-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix pointer to setup_link for 82599.

This resolves some link issues when advertising modes unsupported
by the link partner.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The way __ixgbe_notify_dca() was currently set up it would not be
possible to add a requester. Both cases of the IXGBE_FLAG_DCA_ENABLED
bit being on and off would lead to the function exiting for a
DCA_PROVIDER_ADD.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where WOL would fail on second port of i350
device.
Reported-by: NMartin Wilck <martin.wilck@ts.fujitsu.com>
Reported-by: Stefan Assmann<sassmann@redhat.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The recent commit a6b7a407 when back-ported to the out-of-tree e1000e
driver caused a compilation error on older kernels which required a
re-ordering of the #include files.  This cosmetic patch syncs the two
drivers for easier maintainability.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The array shadow_ram is never NULL.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

after review of all intel drivers, found several instances where
drivers had the incorrect pattern of:
memory mapped write();
delay();

which should always be:
memory mapped write();
write flush(); /* aka memory mapped read */
delay();

explanation:
The reason for including the flush is that writes can be held
(posted) in PCI/PCIe bridges, but the read always has to complete
synchronously and therefore has to flush all pending writes to a
device.  If a write is held and followed by a delay, the delay
means nothing because the write may not have reached hardware
(maybe even not until the next read)
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When TX underrun occurs, a cleanup is performed that marks all buffers
as used. As a side effect it also clears the wrap bit in the last
buffer. This patch will restore the wrap bit.
Signed-off-by: NTord Andersson <tord.andersson@endian.se>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a misusage of the struct usb_cdc_notification to pass arguments to the
usb_control_msg function.  The usb_control_msg function expects host endian
arguments but usb_cdc_notification stores these values as little endian.

Now usb_control_msg is directly invoked with host endian values.
Signed-off-by: NGiuseppe Scrivano <giuseppe@southpole.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unused tx_compressed, tx_compressed and tx_misses fields from
the slip structure. Also, make some device stats generation cleanups.
Signed-off-by: NMatvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use PCI_VENDOR_ID_* from pci_ids.h instead of creating #define locally.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For older FW versions, fixing the usage of per port Mac table.
For each port we must define the base QP number, which is passed
to the HW.
Setting the correct value in SET_PORT FW command to enable the steering.
Reported-by: NRoland Dreier <roland@purestorage.com>
Tested-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dave, I missed out on this line while composing the 4/6 patch from my
yesterday's patchset ("[PATCH net-next 4/6] be2net: use RX_FILTER cmd
to program multicast addresses"). As you've already queued up the
patchset for net-next, I'm sending the fix in a separate patch. Pls
apply.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change detail:
 - Remove obsolete file bfi_ctreg.h as we added new file bfi_reg.h
   consolidating HW reg definitions including the ones for new HW.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Introducing new file bfi_reg.h for consolidating all supported hardware
   registers. This file completely replaces bfi_ctreg.h.
 - Updated ioc code as per register definition change.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - This patch contains removal of get_regs support in bnad_ethtool.c. Thus
   BNA will have minimal register definitions necessary for MBOX and
   interrupt operations
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some BE skews, while in promiscuous mode, pkts that do not belong to a
port can arrive on that port. Drop such pkts.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support for flashing RJ45 PHY (from Teranetics) on a 10GBaseT BE3 card.
Signed-off-by: NNaresh G <bgottumukkala@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use this cmd for both promiscous and multicast address programming. Get rid
of the old MULTICAST_SET cmd.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While configuring promiscous mode, explicitly set the
VLAN_PROMISCOUS bit to make this happen. When switching off
promiscous mode, re-program the vids.
Signed-off-by: NXavier Selvin <xavier.selvin@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change in the link status generates an MCC event. This is processed and
netif_carrier_on/off is called accordingly. Don't need to query/store the
link_status state.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) In be_probe(), as soon as the MCC Q is created a gratuitous link status
event is received and processed. Accordingly netif_carrier_off/on() is called.
The extra netif_carrier_off() call in probe can race with this and cause wrong
state.

2) be_close() need not call netif_carrier_off(). It is OK to show the actual
link state even when the device is administratively down.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After resetting BCM54618se, link partner would still see link since the PHY wasn't put into low-power state.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BCM84833 fail to link due to incorrect auto-negotiation setting.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix no-link issue on BCM578xx when direct attached cable is connected since Warpcore microcode restart was missing to re-read the new mode.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>