Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 161
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 27 1月, 2018 1 次提交
  3. 11 1月, 2018 1 次提交
  5. 06 1月, 2018 1 次提交
    • J
      i40e: setup xdp_rxq_info · 87128824
      由 Jesper Dangaard Brouer 提交于 
      The i40e driver has a special "FDIR" RX-ring (I40E_VSI_FDIR) which is
a sideband channel for configuring/updating the flow director tables.
This (i40e_vsi_)type does not invoke XDP-ebpf code.

As suggested by Björn (V2): Instead of marking this I40E_VSI_FDIR RX-ring
a special case, reverse the logic and only select RX-rings of type
I40E_VSI_MAIN to register xdp_rxq_info's for.

Driver hook points for xdp_rxq_info:
 * reg  : i40e_setup_rx_descriptors (via i40e_vsi_setup_rx_resources)
 * unreg: i40e_free_rx_resources    (via i40e_vsi_free_rx_resources)

Tested on actual hardware with samples/bpf program.

V2: Fixed bug in i40e_set_ringparam (memset zero) + match on I40E_VSI_MAIN.
V4: Update patch desc that got out-of-sync with code.

Cc: intel-wired-lan@lists.osuosl.org
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: NPaul Menzel <pmenzel@molgen.mpg.de>
Acked-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
      87128824
  7. 01 11月, 2017 1 次提交
  9. 25 10月, 2017 1 次提交
    • M
      locking/atomics: COCCINELLE/treewide: Convert trivial ACCESS_ONCE() patterns... · 6aa7de05
      由 Mark Rutland 提交于 
      locking/atomics: COCCINELLE/treewide: Convert trivial ACCESS_ONCE() patterns to READ_ONCE()/WRITE_ONCE()

Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.

For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.

However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:

----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()

// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch

virtual patch

@ depends on patch @
expression E1, E2;
@@

- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)

@ depends on patch @
expression E;
@@

- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.comSigned-off-by: NIngo Molnar <mingo@kernel.org>
      6aa7de05
  11. 18 10月, 2017 13 次提交
  13. 14 10月, 2017 1 次提交
    • A
      i40e: Enable 'channel' mode in mqprio for TC configs · a9ce82f7
      由 Amritha Nambiar 提交于 
      The i40e driver is modified to enable the new mqprio hardware
offload mode and factor the TCs and queue configuration by
creating channel VSIs. In this mode, the priority to traffic
class mapping and the user specified queue ranges are used
to configure the traffic classes by setting the mode option to
'channel'.

Example:
  map 0 0 0 0 1 2 2 3 queues 2@0 2@2 1@4 1@5\
  hw 1 mode channel

qdisc mqprio 8038: root  tc 4 map 0 0 0 0 1 2 2 3 0 0 0 0 0 0 0 0
             queues:(0:1) (2:3) (4:4) (5:5)
             mode:channel
             shaper:dcb

The HW channels created are removed and all the queue configuration
is set to default when the qdisc is detached from the root of the
device.

This patch also disables setting up channels via ethtool (ethtool -L)
when the TCs are configured using mqprio scheduler.

The patch also limits setting ethtool Rx flow hash indirection
(ethtool -X eth0 equal N) to max queues configured via mqprio.
The Rx flow hash indirection input through ethtool should be
validated so that it is within in the queue range configured via
tc/mqprio. The bound checking is achieved by reporting the current
rss size to the kernel when queues are configured via mqprio.

Example:
  map 0 0 0 1 0 2 3 0 queues 2@0 4@2 8@6 11@14\
  hw 1 mode channel

Cannot set RX flow hash configuration: Invalid argument
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
      a9ce82f7
  15. 06 10月, 2017 3 次提交
  17. 03 10月, 2017 1 次提交
  19. 26 8月, 2017 3 次提交
    • A
      i40e: prevent changing ITR if adaptive-rx/tx enabled · 06b2decd
      由 Alan Brady 提交于 
      Currently the driver allows the user to change (or even disable)
interrupt moderation if adaptive-rx/tx is enabled when this should
not be the case.

Adaptive RX/TX will not respect the user's ITR settings so
allowing the user to change it is weird.  This bug would also
allow the user to disable interrupt moderation with adaptive-rx/tx
enabled which doesn't make much sense either.

This patch makes it such that if adaptive-rx/tx is enabled, the user
cannot make any manual adjustments to interrupt moderation.  It also
makes it so that if ITR is disabled but adaptive-rx/tx is then
enabled, ITR will be re-enabled.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
      06b2decd
    • J
      i40e/i40evf: use cmpxchg64 when updating private flags in ethtool · 841c950d
      由 Jacob Keller 提交于 
      When a user gives an invalid command to change a private flag which is
not supported, either because it is read-only, or the device is not
capable of the feature, we simply ignore the request.

A naive solution would simply be to report error codes when one of the
flags was not supported. However, this causes problems because it makes
the operation not atomic. If a user requests multiple private flags
together at once we could end up changing one before failing at the
second flag.

We can do a bit better if we instead update a temporary copy of the
flags variable in the loop, and then copy it into place after. If we
aren't careful this has the pitfall of potentially silently overwriting
any changes caused by other threads.

Avoid this by using cmpxchg64 which will compare and swap the flags
variable only if it currently matched the old value. We'll report
-EAGAIN in the (hopefully rare!) case where the cmpxchg64 fails.

This ensures that we can properly report when flags are not supported in
an atomic fashion without the risk of overwriting other threads changes.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
      841c950d
    • J
      i40e: separate hw_features from runtime changing flags · d36e41dc
      由 Jacob Keller 提交于 
      The number of flags found in pf->flags has grown quite large, and there
are a lot of different types of flags. Most of the flags are simply
hardware features which are enabled on some firmware or some MAC types.
Other flags are dynamic run-time flags which enable or disable certain
features of the driver.

Separate these two types of flags into pf->hw_features and pf->flags.
The hw_features list will contain a set of features which are enabled at
init time. This will not contain toggles or otherwise dynamically
changing features. These flags should not need atomic protections, as
they will be set once during init and then be essentially read only.

Everything else will remain in the flags variable. These flags may be
modified at any time during run time. A future patch may wish to convert
these flags into set_bit/clear_bit/test_bit or similar approach to
ensure atomic correctness.

The I40E_FLAG_MFP_ENABLED flag may be a good fit for hw_features but
currently is used by ethtool in the private flags settings, and thus has
been left as part of flags.

Additionally, I40E_FLAG_DCB_CAPABLE may be a good fit for the
hw_features but this patch has not tried to untangle it yet.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
      d36e41dc
  21. 26 7月, 2017 1 次提交
  23. 21 6月, 2017 2 次提交
  25. 13 6月, 2017 1 次提交
    • J
      i40e: fix handling of HW ATR eviction · 6964e53f
      由 Jacob Keller 提交于 
      A recent commit to refactor the driver and remove the hw_disabled_flags
field accidentally introduced two regressions. First, we overwrote
pf->flags which removed various key flags including the MSI-X settings.

Additionally, it was intended that we have now two flags,
HW_ATR_EVICT_CAPABLE and HW_ATR_EVICT_ENABLED, but this was not done,
and we accidentally were mis-using HW_ATR_EVICT_CAPABLE everywhere.

This patch adds the missing piece, HW_ATR_EVICT_ENABLED, and safely
updates pf->flags instead of overwriting it.

Without this patch we will have many problems including disabling MSI-X
support, and we'll attempt to use HW ATR eviction on devices which do
not support it.

Fixes: 47994c11 ("i40e: remove hw_disabled_flags in favor of using separate flag bits", 2017-04-19)
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6964e53f
  27. 31 5月, 2017 1 次提交
  29. 30 4月, 2017 3 次提交
    • J
      i40e: remove hw_disabled_flags in favor of using separate flag bits · 47994c11
      由 Jacob Keller 提交于 
      The hw_disabled_flags field was added as a way of signifying that
a feature was automatically or temporarily disabled. However, we
actually only use this for FDir features. Replace its use with new
_AUTO_DISABLED flags instead. This is more readable, because you aren't
setting an *_ENABLED flag to *disable* the feature.

Additionally, clean up a few areas where we used these bits. First, we
don't really need to set the auto-disable flag for ATR if we're fully
disabling the feature via ethtool.

Second, we should always clear the auto-disable bits in case they somehow
got set when the feature was disabled. However, avoid displaying
a message that we've re-enabled the feature.

Third, we shouldn't be re-enabling ATR in the SB ntuple add flow,
because it might have been disabled due to space constraints. Instead,
we should just wait for the fdir_check_and_reenable to be called by the
watchdog.

Overall, this change allows us to simplify some code by removing an
extra field we didn't need, and the result should make it more clear as
to what we're actually doing with these flags.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
      47994c11
    • J
      i40e: use DECLARE_BITMAP for state fields · 0da36b97
      由 Jacob Keller 提交于 
      Instead of assuming our flags fit within an unsigned long, use
DECLARE_BITMAP which will ensure that we always allocate enough space.
Additionally, use __I40E_STATE_SIZE__ markers as the last element of the
enumeration so that the size of the BITMAP is compile-time assigned
rather than programmer-time assigned. This ensures that potential future
flag additions do not actually overrun the array. This is especially
important as 32bit systems would only have 32bit longs instead of 64bit
longs as we generally have assumed in the prior code.

This change also removes a dereference of the state fields throughout
the code, so it does have a bit of code churn. The conversions were
automated using sed replacements with an alternation

  s/&(vsi->back|vsi|pf)->state/\1->state/
  s/&adapter->vsi.state/adapter->vsi.state/

For debugfs, we modify the printing so that we can display chunks of the
state value on new lines. This ensures that we can print the entire set
of state values. Additionally, we now print them as 08lx to ensure that
they display nicely.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
      0da36b97
    • J
      i40e: properly spell I40E_VF_STATE_* flags · 6322e63c
      由 Jacob Keller 提交于 
      These flags represent the state of the VF at various times. Do not
spell them as _STAT_ which can be confusing to readers who may think
these refer to statistics.

Change-ID: I6bc092cd472e8276896a1fd7498aced2084312df
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
      6322e63c
  31. 20 4月, 2017 1 次提交
    • J
      i40e: fix CONFIG_BUSY checks in i40e_set_settings function · e8d2f4c6
      由 Jacob Keller 提交于 
      The check for I40E_CONFIG_BUSY state bit in the i40e_set_link_ksettings
function is fishy. First we can notice a few things about the check here.

First a similar check was introduced by commit
'c7d05ca8 ("i40e: driver ethtool core")'

Later a commit introducing the link settings was added by commit
'bf9c7141 ("i40e: Implement set_settings for ethtool")'

However, this second check was against vsi->state instead of pf->state,
and also failed to set the bit, it only checks. That indicates the locking
was not quite correct. The only other place that the state bit
in vsi->state gets used is to protect the filter list.

Since this code does not care about the mac filter list,  and seems
clear the original code should have set the pf->state bit. Fix these
issues by using pf->state correctly, and by actually setting the bit
so that we properly lock as expected.

Since these checks occur while holding the rtnl_lock(), lets also add a
timeout so that we don't potentially softlock the system.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
      e8d2f4c6
  33. 08 4月, 2017 2 次提交
  35. 29 3月, 2017 2 次提交
  37. 28 3月, 2017 1 次提交