- 04 12月, 2007 11 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched: sched: cpu accounting controller (V2)
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: [SCSI] NCR5380: Fix bugs and canonicalize irq handler usage [SCSI] zfcp: fix cleanup of dismissed error recovery actions [SCSI] zfcp: fix dismissal of error recovery actions [SCSI] qla1280: convert to use the data buffer accessors [SCSI] iscsi: return data transfer residual for data-out commands [SCSI] iscsi_tcp: fix potential lockup with write commands [SCSI] aacraid: fix security weakness [SCSI] aacraid: fix up le32 issues in BlinkLED [SCSI] aacraid: fix potential panic in thread stop [SCSI] aacraid: don't assign cpu_to_le32(constant) to u8
-
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (27 commits) [INET]: Fix inet_diag dead-lock regression [NETNS]: Fix /proc/net breakage [TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure [NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK [NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON [DECNET]: dn_nl_deladdr() almost always returns no error [IPV6]: Restore IPv6 when MTU is big enough [RXRPC]: Add missing select on CRYPTO mac80211: rate limit wep decrypt failed messages rfkill: fix double-mutex-locking mac80211: drop unencrypted frames if encryption is expected mac80211: Fix behavior of ieee80211_open and ieee80211_close ieee80211: fix unaligned access in ieee80211_copy_snap mac80211: free ifsta->extra_ie and clear IEEE80211_STA_PRIVACY_INVOKED SCTP: Fix build issues with SCTP AUTH. SCTP: Fix chunk acceptance when no authenticated chunks were listed. SCTP: Fix the supported extensions paramter SCTP: Fix SCTP-AUTH to correctly add HMACS paramter. SCTP: Fix the number of HB transmissions. [TCP] illinois: Incorrect beta usage ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6由 Linus Torvalds 提交于
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits) LIB82596: correct data types for hardware addresses via-velocity: don't oops on MTU change (resend) Stop phy code from returning success to unknown ioctls. SET_NETDEV_DEV() in fec_mpc52xx.c net: smc911x: only enable for mpr2 on sh. e1000: Fix NAPI state bug when Rx complete sky2: turn of dynamic Tx watermark workaround (FE+ only) sky2: don't use AER routines sky2: revert to access PCI config via device space cxgb - fix stats cxgb - fix NAPI cxgb - fix T2 GSO ucc_geth: handle passing of RX-only and TX-only internal delay PHY connection type parameters phylib: marvell: add support for TX-only and RX-only Internal Delay phylib: add PHY interface modes for internal delay for tx and rx only skge: MTU changing fix skge: serial mode register values skge version 1.13 skge: increase TX threshold for Jumbo skge: fiber link up/down fix ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev由 Linus Torvalds 提交于
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: sata_mv: Fix broken Marvell 7042 support. libata: Fix early use of port printk. (Was Re: ata4294967295: failed to start port (errno=-19)) ata_piix: add more toshiba laptops to broken suspend list libata: More IVB horkage from TSST libata: report protocol and full CDB on error Several fixes for the AVR32 PATA driver sata_mv: fix compilation error when enabling DEBUG Set proper ATA UDMA mode for bf548 according to system clock.
-
由 Vivek Goyal 提交于
Signed-off-by: NVivek Goyal <vgoyal@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jeff Dike 提交于
Under the conditions that UML uses it, tcgetattr is guaranteed to return -EINTR when the console is attached to /dev/ptmx, making generic_console_write hang because it loops, calling tcgetattr until it succeeds. This is a host bug - see http://marc.info/?l=linux-kernel&m=119618990807182&w=2 for the details. This patch works around it by blocking SIGIO while the terminal attributes are being fiddled. Signed-off-by: NJeff Dike <jdike@linux.intel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jeff Dike 提交于
I forgot to have an int-returning function actually return something. Signed-off-by: NJeff Dike <jdike@linux.intel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Al Viro 提交于
The previous commit ("uml: keep UML Kconfig in sync with x86") is not enough, unfortunately. If we go that way, we need to add dependencies on !UML for several options. Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NJeff Dike <jdike@linux.intel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jeff Dike 提交于
Fix a UML build breakage introduced by commit 1032c0ba - it introduces X86_32, with many things which UML needs depending on it. This patch adds definitions of X86_32 and RWSEM_XCHGADD_ALGORITHM to the UML/i386 Kconfig. Signed-off-by: NJeff Dike <jdike@linux.intel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Karsten Keil 提交于
Fix possible memory overrun issue in the isdn ioctl code. Found by ADLAB <adlab@venustech.com.cn> Signed-off-by: NKarsten Keil <kkeil@suse.de> Cc: ADLAB <adlab@venustech.com.cn> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 03 12月, 2007 2 次提交
-
-
由 Herbert Xu 提交于
The inet_diag register fix broke inet_diag module loading because the loaded module had to take the same mutex that's already held by the loader in order to register the new handler. This patch fixes it by introducing a separate mutex to protect the handling of handlers. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
-
由 Srivatsa Vaddagiri 提交于
Commit cfb52856 removed a useful feature for us, which provided a cpu accounting resource controller. This feature would be useful if someone wants to group tasks only for accounting purpose and doesnt really want to exercise any control over their cpu consumption. The patch below reintroduces the feature. It is based on Paul Menage's original patch (Commit 62d0df64), with these differences: - Removed load average information. I felt it needs more thought (esp to deal with SMP and virtualized platforms) and can be added for 2.6.25 after more discussions. - Convert group cpu usage to be nanosecond accurate (as rest of the cfs stats are) and invoke cpuacct_charge() from the respective scheduler classes - Make accounting scalable on SMP systems by splitting the usage counter to be per-cpu - Move the code from kernel/cpu_acct.c to kernel/sched.c (since the code is not big enough to warrant a new file and also this rightly needs to live inside the scheduler. Also things like accessing rq->lock while reading cpu usage becomes easier if the code lived in kernel/sched.c) The patch also modifies the cpu controller not to provide the same accounting information. Tested-by: NBalbir Singh <balbir@linux.vnet.ibm.com> Tested the patches on top of 2.6.24-rc3. The patches work fine. Ran some simple tests like cpuspin (spin on the cpu), ran several tasks in the same group and timed them. Compared their time stamps with cpuacct.usage. Signed-off-by: NSrivatsa Vaddagiri <vatsa@linux.vnet.ibm.com> Signed-off-by: NBalbir Singh <balbir@linux.vnet.ibm.com> Signed-off-by: NIngo Molnar <mingo@elte.hu>
-
- 02 12月, 2007 27 次提交
-
-
由 Mark Lord 提交于
sata_mv: Fix broken Marvell 7042 support. The Marvell 7042 chip is more or less the same as the 6042 internally, but sports a PCIe bus. Despite having identical SATA cores, the 7042 does differ from its PCI bus counterparts in placment and layout of certain bus related registers. This patch fixes sata_mv to distinguish between the PCI bus registers of earlier chips, and the PCIe bus registers of the 7042. Specifically, move the offsets and bit patterns for the PCI/PCIe interrupt cause/mask registers into the struct mv_host_priv, as these values differ between the 6xxx and 7xxx series chips. This fixes the driver to not access reserved PCI addresses, and prevents the lockups reported in linux-2.6.24 with 7042 boards. Also add a new PCI ID for the Highpoint 2300 7042-based board that I'm using for testing this stuff here. Tested with Marvell 6081 + 7042 chips, on x86 & x86_64. Signed-off-by: NMark Lord <mlord@pobox.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Alan Cox 提交于
On Fri, 30 Nov 2007 14:34:11 +0200 (EET) Meelis Roos <mroos@linux.ee> wrote: > > Can you stick a stack trace in at that point ? That would help diagnose > > it a great deal quicker. > > Finally done - found out hard way that BUG() is too bad and > dump_st5ack() suits me better. Thanks. This should fix the real cause, and also allow for port start to fail politely with -ENODEV. Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Peter Schwenke 提交于
Add more toshiba laptops to broken suspend list. This is from OSDL bugzilla bug 7780. tj: re-formatted patch and added description and SOB. Signed-off-by: NPeter Schwenke <peter@bluetoad.com.au> Signed-off-by: NTejun Heo <htejun@gmail.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Peter Missel 提交于
libata: Add more TSST (Samsung/Toshiba) IDE drives with broken cable detection validation bits. signed-off-by: Peter Missel (peter.missel@onlinehome.de) Acked-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Tejun Heo 提交于
Protocol and CDB allocation size field are important in determining what went wrong with ATAPI commands. Report them on failure. Signed-off-by: NTejun Heo <htejun@gmail.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
Several fixes for the AVR32 PATA driver: * Updated to use new AVR32 SMC timing API. This removes the need for "magic" constants in signal timing. * Removed the ATA_FLAG_PIO_POLLING, the driver should use interrupts. * Removed .port_disable and .irq_ack as these are no longer needed. * Improved some comments. Signed-off-by: NKristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Saeed Bishara 提交于
use sstatus instead status. Signed-off-by: NSaeed Bishara <saeed@marvell.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 sonic zhang 提交于
UDMA Mode - Frequency compatibility UDMA5 - 100 MB/s - SCLK = 133 MHz UDMA4 - 66 MB/s - SCLK >= 80 MHz UDMA3 - 44.4 MB/s - SCLK >= 50 MHz UDMA2 - 33 MB/s - SCLK >= 40 MHz Signed-off-by: NSonic Zhang <sonic.zhang@analog.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Thomas Bogendoerfer 提交于
dma_addr_t is 64bit wide on some architectures (for example 64bit MIPS), so it's not a good idea to use it for 32bit wide addresses in descriptors. Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
The VIA veloicty driver needs the following to allow changing MTU when down. The buffer size needs to be computed when device is brought up, not when device is initialized. This also fixes a bug where the buffer size was computed differently on change_mtu versus initial setting. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 David Woodhouse 提交于
This kind of sucks, and prevents the Fedora installer from using the device for network installs... [root@efika phy]# iwconfig eth0 Warning: Driver for device eth0 has been compiled with an ancient version of Wireless Extension, while this program support version 11 and later. Some things may be broken... eth0 ESSID:off/any Nickname:"" NWID:0 Channel:0 Access Point: 00:00:BF:81:14:E0 Bit Rate:-1.08206e+06 kb/s Sensitivity=0/0 RTS thr:off Fragment thr:off Encryption key:<too big> Power Management:off Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 David Woodhouse 提交于
This helps to allow the Fedora installer to use the built-in Ethernet on the Efika for a network install. Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Paul Mundt 提交于
The smc911x.h is a bit of a mess, not supporting any sort of generic configuration. For the moment only ARCH_PXA and SH_MAGIC_PANEL_R2 have suitable definitions, so we reflect this in the Kconfig also. While there are other SH boards that will likely turn this on in the 2.6.25 time frame, it's not worth trying to stub around at the moment. Fixes up the allmodconfig build, as noted by akpm. Signed-off-by: NPaul Mundt <lethal@linux-sh.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Auke Kok 提交于
Don't exit polling when we have not yet used our budget, this causes the NAPI system to end up with a messed up poll list. Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
Add workaround for issues FE+ (A0) transmit watermark. This is copied verbatim from vendor driver sk98lin (10.22.4.3). Don't have that chip version and no more information seems to be available. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
Using PCIE advanced error recovery stuff creates more user problems than it's worth. The AER stuff depends on MMCONFIG and in many configurations it just doesn't work. Plus it doesn't add any real functionality to the driver. The sky2 driver handles its own errors fine as is. This reverts 555382cbSigned-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
Using the hardware window into PCI config space is more reliable and smaller/faster than using the pci_config routines. It avoids issues with MMCONFIG etc. Reverts: 167f53d0 Please apply for 2.6.24 Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Divy Le Ray 提交于
Fix MAC stats accounting. Fix get_stats. Signed-off-by: NDivy Le Ray <divy@chelsio.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Divy Le Ray 提交于
netif_rx_complete() should be called only when work_done < budget. Signed-off-by: NDivy Le ray <divy@chelsio.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Divy Le Ray 提交于
The patch ensures that a GSO skb has enough headroom to push an encapsulating cpl_tx_pkt_lso header. Signed-off-by: NDivy Le Ray <divy@chelsio.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Kim Phillips 提交于
Extend the RGMII-Internal Delay specification case to include TX-only and RX-only variants. Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Tested-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Acked-by: NLi Yang <leoli@freescale.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Kim Phillips 提交于
Previously, Internal Delay specification implied the delay be applied to both TX and RX. This patch allows for separate TX/RX-only internal delay specification. Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Tested-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Acked-by: NLi Yang <leoli@freescale.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Kim Phillips 提交于
Allow phylib specification of cases where hardware needs to configure PHYs for Internal Delay only on either RX or TX (not both). Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Tested-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Acked-by: NLi Yang <leoli@freescale.com> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
The code to change MTU doesn't correctly handle all the chip variations and requirements for restarting. On Genesis chips changing MTU would just cause receiver to hang. Use a simpler approach of just taking link down/up if needed. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
For compatiablity with sk98lin, make sure and set same values in serial mode register. Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
Version for 2.6.24 Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-
由 Stephen Hemminger 提交于
Need to increase TX threshold when doing Jumbo frames on dual port board to avoid underruns. (Code from sk98lin). Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NJeff Garzik <jeff@garzik.org>
-