Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 04 9月, 2009 12 次提交
    • H
      OMAP clock: use debugfs_remove_recursive() for rewinding · ca4caa4e
      由 Hiroshi DOYU 提交于 
      Rewinding each debugfs entries to unregister if an error happens.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      ca4caa4e
    • P
      OMAP2/3/4 core: create omap_device layer · b04b65ab
      由 Paul Walmsley 提交于 
      The omap_device code provides a mapping of omap_hwmod structures into
the platform_device system, and includes some details on external
(board-level) integration.  This allows drivers to enable, idle, and
shutdown on-chip device resources, including clocks, regulators, etc.
The resources enabled and idled are dependent on the device's maximum
wakeup latency constraint (if present).

At the moment, omap_device functions are intended to be called from
platform_data function pointers.  Ideally in the future these
functions will be called from either subarchitecture-specific
platform_data activate, deactivate functions, or via an custom
bus/device type for OMAP.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Eric Thomas <ethomas@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
      b04b65ab
    • P
      OMAP: omap_hwmod: call omap_hwmod init at boot; create interconnects · 02bfc030
      由 Paul Walmsley 提交于 
      Connect the omap_hwmod code to the kernel boot.  Create some basic
interconnect and device structures for OMAP2/3 chips.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      02bfc030
    • P
      OMAP2/3/4: create omap_hwmod layer · 63c85238
      由 Paul Walmsley 提交于 
      OMAP SoCs can be considered a collection of hardware IP blocks
connected by various interconnects.  The bus topology and device
integration data is somewhat more complex than platform_device can
encode.  This patch creates code and structures to manage information
about OMAP on-chip devices ("hardware modules") and their integration
to the rest of the chip.  Hardware module data is intended to be
generated dynamically from the TI hardware database for the OMAP4
chips and beyond, easing Linux support for new chip variants.

This code currently:

- resets and configures all hardware modules upon startup, reducing bootloader
  dependencies;

- provides hooks for Linux driver model code to enable, idle, and shutdown
  hardware modules (forthcoming patch);

- waits for hardware modules to leave idle once their clocks
  are enabled and OCP_SYSCONFIG bits are set appropriately.

- provides a means to pass arbitrary IP block configuration data (e.g.,
  FIFO size) to the device driver (via the dev_attr void pointer)

In the future this code is intended to:

- estimate interconnect bandwidth and latency characteristics to
  ensure constraints are satisfied during DVFS

- provide *GRPSEL bit data to the powerdomain code

- handle pin/ball muxing for devices

- generate IO mapping information dynamically

- supply device firewall configuration data

- provide hardware module data to other on-chip coprocessor software

- allow the removal of the "disable unused clocks" code in the OMAP2/3
  clock code

This patch represents a collaborative effort involving many people from TI,
Nokia, and the Linux-OMAP community.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Eric Thomas <ethomas@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
      63c85238
    • P
      OMAP2/3 board-*.c files: read bootloader configuration earlier · b3c6df3a
      由 Paul Walmsley 提交于 
      Most board-*.c files read configuration data from the bootloader in
their .init_machine() function.  This needs to happen earlier, at some
point before omap2_init_common_hw() is called.  This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      b3c6df3a
    • P
      OMAP2/3/4 PRCM: add module IDLEST wait code · 71348bca
      由 Paul Walmsley 提交于 
      After a hardware module's clocks are enabled, Linux must wait for it
to indicate readiness via its IDLEST bit before attempting to access
the device, otherwise register accesses to the device may trigger an
abort.  This has traditionally been implemented in the clock
framework, but this is the wrong place for it: the clock framework
doesn't know which module clocks must be enabled for a module to leave
idle; and if a module is not in smart-idle mode, it may never leave
idle at all.  This type of information is best stored in a
per-hardware module data structure (coming in a following patch),
rather than a per-clock data structure.  The new code will use these new
functions to handle waiting for modules to enable.

Once hardware module data is filled in for all of the on-chip devices,
the clock framework code to handle IDLEST waiting can be removed.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      71348bca
    • P
      OMAP2/3 PM: create the OMAP PM interface and add a default OMAP PM no-op layer · c0407a96
      由 Paul Walmsley 提交于 
      The interface provides device drivers, CPUFreq, and DSPBridge with a
means of controlling OMAP power management parameters that are not yet
supported by the Linux PM PMQoS interface.  Copious documentation is
in the patch in Documentation/arm/OMAP/omap_pm and the interface
header file, arch/arm/plat-omap/include/mach/omap-pm.h.

Thanks to Rajendra Nayak <rnayak@ti.com> for adding CORE (VDD2) OPP
support and moving the OPP table initialization earlier in the event
that the clock code needs them.  Thanks to Tero Kristo
<tero.kristo@nokia.com> for fixing the parameter check in
omap_pm_set_min_bus_tput().  Jouni signed off on Tero's patch.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NJouni Högander <jouni.hogander@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Igor Stoppa <igor.stoppa@nokia.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Veeramanikandan Raju <veera@ti.com>
Cc: Karthik Dasu <karthik-dp@ti.com>
      c0407a96
    • P
      OMAP3 clock: remove superfluous calls to omap2_init_clk_clkdm · 08e3d5f2
      由 Paul Walmsley 提交于 
      omap2_init_clk_clkdm() is called as part of the chip architecture-specific
initialization code, so calling it again from the struct clk init pointer
just wastes cycles.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      08e3d5f2
    • P
      OMAP clock: associate MPU clocks with the mpu_clkdm · 19f4d3a9
      由 Paul Walmsley 提交于 
      All MPU-related clocks should be in the mpu_clkdm.  This is needed for the
upcoming omap_hwmod patches, which needs to know the clockdomain that arm_fck
is in.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      19f4d3a9
    • S
      OMAP3 clock: Fixed processing of bootarg 'mpurate' · 11b66383
      由 Sanjeev Premi 提交于 
      The argument 'mpurate' had no effect on the MPU
frequency. This patch fixes the same.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      11b66383
    • T
      OMAP: SDRC: Add several new register definitions · 6dda2d4b
      由 Tero Kristo 提交于 
      Add missing SDRC register offset macros.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: added commit message]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      6dda2d4b
    • P
      OMAP: powerdomain: Fix overflow when doing powerdomain deps lookups. · 5d113262
      由 Paul Walmsley 提交于 
      At the end of the list pd is a pointer to a NULL struct, so checking
if the address == NULL doesn't help here. In fact the original code
will just keep running past the struct to read who knows what in
memory.

This case manifests itself when from clkdms_setup() when enabling auto
idle for a clock domain and the clockdomain usecount is greater than
0. When _clkdm_add_autodeps() tries to add the a dependency that does
not exist in the powerdomain->wkdep_srcs array the for loop will run
past the wkdep_srcs array.

Currently in linux-omap you won't hit this because the not found case
is never executed, unless you start modifying powerdomains and their
wakeup/sleep deps.
Signed-off-by: NMike Chan <mike@android.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      5d113262
  3. 29 8月, 2009 21 次提交
  5. 28 8月, 2009 7 次提交