The values used to determined if the adapter is running in single or
multi-function mode were previously modified to the values necessary
when making the VXGE_HW_FW_API_GET_FUNC_MODE firmware call.  However,
the firmware call was not modified.  This had the driver printing out on
probe that the adapter was in multi-function mode when in single
function mode and vice versa.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Detect if the adapter is Titan or Titan1A, and tune the driver for this
hardware.  Also, remove unnecessary function __vxge_hw_device_id_get.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate the return code of the call to vxge_hw_vpath_fw_api and
__vxge_hw_vpath_pci_func_mode_get.  This enables the proper handling of
error conditions when querying the function mode of the device during
probe.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for enable/disabling hardware timestamping on receive
packets via ioctl call.  When enabled, the hardware timestamp replaces
the FCS in the payload.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the ability in the vxge driver to flash firmware via ethtool.

Updated to include comments from Ben Hutchings.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible for multiple callers to access the firmware interface for
the same vpath simultaneously, resulting in uncertain output.  Add locks
to serialize access.  Also, make functions only accessed locally static,
thus requiring some movement of code blocks.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove all of the unnecessary debug printk indirection and temporary
variables for vxge_debug_ll and vxge_assert.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Wait for the receive traffic to become idle before attempting to close
or reset the adapter.  To enable the processing of packets while Receive
Idle, move the clearing of __VXGE_STATE_CARD_UP bit in vxge_close to
after it.  Also, modify the return value of the ISR when the adapter is
down to IRQ_HANDLED.  Otherwise there are unhandled interrupts for the
device.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable RSS hashing and add ability to pass up the adapter calculated rx
hash up the network stack (if feature is available).  Add the ability to
enable/disable feature via ethtool, which requires that the adapter is
not running at the time.  Other miscellaneous cleanups and fixes
required to get RSS working.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NRam Vepa <ram.vepa@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default we add firmware information to ethtool get regs.
Optionally firmware info can instead be sent to log.
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Coalesce long formats.
Align arguments.
Remove KERN_<level>.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Coalesce long formats.
Add missing newlines.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing newlines.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing newlines.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some network drivers use old TX_TIMEOUT definitions, assuming HZ=100 of
old kernels.

Convert these definitions to include HZ, since HZ can be 1000 these
days.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

unix_dgram_poll() is pretty expensive to check POLLOUT status, because
it has to lock the socket to get its peer, take a reference on the peer
to check its receive queue status, and queue another poll_wait on
peer_wait. This all can be avoided if the process calling
unix_dgram_poll() is not interested in POLLOUT status. It makes
unix_dgram_recvmsg() faster by not queueing irrelevant pollers in
peer_wait.

On a test program provided by Alan Crequy :

Before:

real    0m0.211s
user    0m0.000s
sys     0m0.208s

After:

real    0m0.044s
user    0m0.000s
sys     0m0.040s
Suggested-by: NDavide Libenzi <davidel@xmailserver.org>
Reported-by: NAlban Crequy <alban.crequy@collabora.co.uk>
Acked-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alban Crequy reported a problem with connected dgram af_unix sockets and
provided a test program. epoll() would miss to send an EPOLLOUT event
when a thread unqueues a packet from the other peer, making its receive
queue not full.

This is because unix_dgram_poll() fails to call sock_poll_wait(file,
&unix_sk(other)->peer_wait, wait);
if the socket is not writeable at the time epoll_ctl(ADD) is called.

We must call sock_poll_wait(), regardless of 'writable' status, so that
epoll can be notified later of states changes.

Misc: avoids testing twice (sk->sk_shutdown & RCV_SHUTDOWN)
Reported-by: NAlban Crequy <alban.crequy@collabora.co.uk>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of wakeup all sleepers, use wake_up_interruptible_sync_poll() to
wakeup only ones interested into writing the socket.

This patch is a specialization of commit 37e5540b (epoll keyed
wakeups: make sockets use keyed wakeups).

On a test program provided by Alan Crequy :

Before:
real    0m3.101s
user    0m0.000s
sys     0m6.104s

After:

real	0m0.211s
user	0m0.000s
sys	0m0.208s
Reported-by: NAlban Crequy <alban.crequy@collabora.co.uk>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While tracking dev_base_lock users, I found decnet used it in
dnet_select_source(), but for a wrong purpose:

Writers only hold RTNL, not dev_base_lock, so readers must use RCU if
they cannot use RTNL.

Adds an rcu_head in struct dn_ifaddr and handle proper RCU management.

Adds __rcu annotation in dn_route as well.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NSteven Whitehouse <swhiteho@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bond_info_seq_start() uses a read_lock(&dev_base_lock) to make sure
device doesn’t disappear. Same goal can be achieved using RCU.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_base_lock is the legacy way to lock the device list, and is planned
to disappear. (writers hold RTNL, readers hold RCU lock)

Convert aoecmd_cfg_pkts() to RCU locking.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add suspend/resume support using default open/stop interface methods
to do hardware dependant operations.

On suspend, same low power state (soft power mode) will be kept, the
following blocks will be disabled:

 - Internal PLL Clock
 - Tx/Rx PHY
 - MAC
 - SPI Interface
Signed-off-by: NAbraham Arce <x0066660@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sgs allocation error path leaks the allocated message.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Acked-by: NAndy Grover <andy.grover@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

QDIO is running independent from netdevice state. We are not
allowed to schedule NAPI in case the netdevice is not open.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For a certain Hipersockets specific error code in the xmit path, the
qeth driver tries to invoke dev_queue_xmit again.
Commit 79640a4c introduces a busylock
causing locking problems in case of re-invoked dev_queue_xmit by qeth.
This patch removes the attempts to retry packet sending with
dev_queue_xmit from the qeth driver.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fix a bug reported by backyes.
Right the first time pktgen's using queue_map that's not been initialized
by set_cur_queue_map(pkt_dev);
Signed-off-by: NJunchang Wang <junchangwang@gmail.com>
Signed-off-by: NBackyes <backyes@mail.ustc.edu.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After e6484930: net: allocate tx queues in register_netdevice
These calls make net drivers oops at load time, so let's avoid people
git-bisect'ing known problems.
Signed-off-by: NGuillaume Chazarain <guichaz@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After e6484930: net: allocate tx queues in register_netdevice
It causes an Oops at skge_probe() time.
Signed-off-by: NGuillaume Chazarain <guichaz@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The type of FRAG6_CB(prev)->offset is int, skb->len is *unsigned* int,
and offset is int.

Without this patch, type conversion occurred to this expression, when
(FRAG6_CB(prev)->offset + prev->len) is less than offset.
Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The basic classifier keeps statistics but does not report it to user space.
This showed up when using basic classifier (with police) as a default catch
all on ingress; no statistics were reported.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing 'FirmwareVersion' attribute only covers the DSP firmware as
provided by Conexant; not the overall version of the device firmware. We
do want to be able to see the full version number too.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: Add new ext4 inode tracepoints
  ext4: Don't call sb_issue_discard() in ext4_free_blocks()
  ext4: do not try to grab the s_umount semaphore in ext4_quota_off
  ext4: fix potential race when freeing ext4_io_page structures
  ext4: handle writeback of inodes which are being freed
  ext4: initialize the percpu counters before replaying the journal
  ext4: "ret" may be used uninitialized in ext4_lazyinit_thread()
  ext4: fix lazyinit hang after removing request

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  TTY: move .gitignore from drivers/char/ to drivers/tty/vt/
  TTY: create drivers/tty/vt and move the vt code there
  TTY: create drivers/tty and move the tty core files there

Merge branch 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-next-2.6

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-next-2.6:
  Staging: ath6kl: remove empty files that mess with 'distclean'
  staging: ath6kl: Fixing the driver to use modified mmc_host structure
  Staging: solo6x10: fix build problem

Merge branch 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  mmc: sh_mmcif: Convert extern inline to static inline.
  ARM: mach-shmobile: Allow GPIO chips to register IRQ mappings.
  ARM: mach-shmobile: fix sh7372 after a recent clock framework rework
  ARM: mach-shmobile: include drivers/sh/Kconfig
  ARM: mach-shmobile: ap4evb: Add HDMI sound support
  ARM: mach-shmobile: clock-sh7372: Add FSIDIV clock support
  ARM: shmobile: remove sh_timer_config clk member

* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: clkfwk: Fix up checkpatch warnings.
  sh: make some needlessly global sh7724 clocks static
  sh: add clk_round_parent() to optimize parent clock rate
  sh: Simplify phys_addr_mask()/PTE_PHYS_MASK for 29/32-bit.
  sh: nommu: Support building without an uncached mapping.
  sh: nommu: use 32-bit phys mode.
  sh: mach-se: Fix up SE7206 no ioport build.
  sh: intc: Update for single IRQ reservation helper.
  sh: clkfwk: Fix up rate rounding error handling.
  sh: mach-se: Rip out superfluous 7751 PIO routines.
  sh: mach-se: Rip out superfluous 770x PIO routines.
  sh: mach-edosk7705: Kill off machtype, consolidate board def.
  sh: mach-edosk7705: update for this century, kill off PIO trapping.
  sh: mach-se: Rip out superfluous 7206 PIO routines.
  sh: mach-systemh: Kill off dead board.
  sh: mach-snapgear: Kill off machtype, consolidate board def.
  sh: mach-snapgear: Rip out superfluous PIO routines.
  sh: mach-microdev: SuperIO-relative ioport mapping.

Add ext4_evict_inode, ext4_drop_inode, ext4_mark_inode_dirty, and
ext4_begin_ordered_truncate()
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>