The pen down IRQ will toggle during each X,Y,Z measurement cycle.
Even though the IRQ is disabled it will be latched and delivered
when after enable_irq. Thus in the IRQ handler we must avoid
starting a new measurement cycle when such an "unwanted" IRQ happens.
Add a get_pendown_state platform function, which will probably
determine this by reading the current GPIO level of the pen IRQ pin.

Move the IRQ reenabling from the SPI RX function to the timer. After
the last power down message the pen IRQ pin is still active for a
while and get_pendown_state would report incorrectly a pen down state.

When suspending we should check the ts->pending flag instead of
ts->pendown, since the timer can be pending regardless of ts->pendown.
Also if ts->pending is set we can be sure that the timer is running,
so no need to rearm it. Similarly if ts->pending is not set we can
be sure that the IRQ is enabled (and the timer is not).
Signed-off-by: NImre Deak <imre.deak@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

- Add disable attribute to support device locking mode where
  unintentional touch event shouldn't wake up the system;
- Update comments;
- Add missing spin_lock_init;
- Do device resume with the lock held;
- Do cleanup calls / free memory in the reverse order of initialization.
Signed-off-by: NImre Deak <imre.deak@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Sometimes a polling loop had a hard time changing state without
pre-emption enabled.  Use msleep instead, it's better anyway.
Signed-off-by: NJuha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Some touchscreens seem to oscillate heavily for a while after touching
the screen.  Implement support for sampling the screen until we get two
consecutive values that are close enough.
Signed-off-by: NImre Deak <imre.deak@nokia.com>
Signed-off-by: NJuha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Submit a seperate request for powering down the ADC in ads7846,
doing it after the last read request.  Otherwise some of the read
values are incorrect.
Signed-off-by: NImre Deak <imre.deak@nokia.com>
Signed-off-by: NJuha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

It's handy for userspace diagnostics to see the pen down status, to
see whether the touchscreen is "stuck" (shortcircuited).
Signed-off-by: NImre Deak <imre.deak@nokia.com>
Signed-off-by: NJuha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

- Add KEY_BRL_* input keys and K_BRL_* keycodes;
- Add emulation of how braille keyboards usually combine braille dots
  to the console keyboard driver;
- Add handling of unicode U+28xy diacritics.
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Toshiba Protege M300 also requires the same workaround as Satellites
and Dynabooks - Synaptics report rate should be lowered to 40pps
(from 80), otherwise KBC starts losing keypresses.
Signed-off-by: NRichard Thrippleton <ret28@cam.ac.uk>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

SNES gamepads and mice share the same type of interface so they both can be
connected to the parallel port using a simple interface.  Adding mouse
support to a gamepad driver may sound funny at first, but doing so in this
case makes it possible to connect and SNES gamepads and mice at the same
time, on the same port.
Signed-off-by: NRaphael Assenat <raph@raphnet.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

sysfs can't handle more than PAGE_SIZE data coming from attributes'
show() methods; make sure we respect this limit.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Decrease the number of pointer derefs in drivers/serial/jsm/jsm_tty.c

Benefits of the patch:
 - Fewer pointer dereferences should make the code slightly faster.
 - Size of generated code is smaller
 - Improved readability
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Acked-by: N"V. ANANDA KRISHNAN" <mansarov@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NBrad Campbell <brad@wasp.net.au>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

And remove the comments that were put in inplace of a fix too....
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Currently a device failure during recovery leaves bits set in the bitmap.
This normally isn't a problem as the offending device will be rejected because
of errors.  However if device re-adding is being used with non-persistent
bitmaps, this can be a problem.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch removes the old radeon driver which has been replaced by a
newer one.
Signed-off-by: NMichael Hanselmann <linux-kernel@hansmi.ch>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The monochrome->color expansion routine that handles bitmaps which have
(widths % 8) != 0 (slow_imageblit) produces corrupt characters in big-endian.
This is caused by a bogus bit test in slow_imageblit().

Fix.

This patch may deserve to go to the stable tree.  The code has already been
well tested in little-endian machines.  It's only in big-endian where there is
uncertainty and Herbert confirmed that this is the correct way to go.

It should not introduce regressions.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Acked-by: NHerbert Poetzl <herbert@13thfloor.at>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fixes for the pxafb driver:

* Return -EINVAL for resolutions that are too large as per framebuffer
  driver policy.

* Increase the error timeout for disabling the LCD controller.  The current
  timeout is sometimes too short on the Sharp Zaurus Cxx00 hardware and an
  extra delay in an error path shouldn't pose any problems.

* Fix a dev reference which causes a compile error when DEBUG is defined.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Generalise the Corgi backlight driver by moving the default intensity and
limit mask settings into the platform specific data structure.  This enables
the driver to support other Zaurus hardware, specifically the SL-6000x (Tosa)
model.

Also change the spinlock to a mutex (the spinlock is overkill).
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Updates to the HP Jornada 680 Backlight driver:

- Correct the suspend/resume functions so the driver compiles
  (SUSPEND_POWER_DOWN/RESUME_POWER_ON no longer exist).

- Convert the driver to match the recent platform device changes.

- Replace the unsafe static struct platform_device with dynamic allocation.

- Convert the driver to the new backlight code.

This has not been tested on a device due to lack of hardware but wouldn't
compile beforehand.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Backlight class attributes are currently easy to implement incorrectly.
Moving certain handling into the backlight core prevents this whilst at the
same time makes the drivers simpler and consistent.  The following changes are
included:

The brightness attribute only sets and reads the brightness variable in the
backlight_properties structure.

The power attribute only sets and reads the power variable in the
backlight_properties structure.

Any framebuffer blanking events change a variable fb_blank in the
backlight_properties structure.

The backlight driver has only two functions to implement.  One function is
called when any of the above properties change (to update the backlight
brightness), the second is called to return the current backlight brightness
value.  A new attribute "actual_brightness" is added to return this brightness
as determined by the driver having combined all the above factors (and any
driver/device specific factors).

Additionally, the backlight core takes care of checking the maximum brightness
is not exceeded and of turning off the backlight before device removal.

The corgi backlight driver is updated to reflect these changes.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add acceleration support in w100fb.c (i.e.  ATI Imageons) for the copyarea and
fillrect operations.
Signed-off-by: NAlberto Mardegan <mardy@users.sourceforge.net>
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The current display was not saved during initialization.  This leads to hard
to track console corruption, such as a misplaced cursor, which is correctible
by switching consoles.  Fix this minor bug.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add an LED trigger for IDE disk activity to the ide-disk driver.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Acked-by: NBartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Ensure ide-taskfile.c calls any driver specific end_request function if
present.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NBartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Adds LED drivers for LEDs found on the Sharp Zaurus c6000 model (tosa).
Signed-off-by: NDirk Opfer <dirk@opfer-online.de>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

NEW_LEDS support for ixp4xx boards where LEDs are connected to the GPIO lines.

This includes a new generic ixp4xx driver (leds-ixp4xx-gpio.c name
"IXP4XX-GPIO-LED")
Signed-off-by: NJohn Bowler <jbowler@acm.org>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Adds an LED driver for LEDs exported by the Sharp LOCOMO chip as found on some
models of Sharp Zaurus.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Adds LED drivers for LEDs found on the Sharp Zaurus c7x0 (corgi, shepherd,
husky) and cxx00 (akita, spitz, borzoi) models.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add an example of a complex LED trigger in the form of a generic timer which
triggers the LED its attached to at a user specified frequency and duty cycle.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add support for LED triggers to the LED subsystem.  "Triggers" are events
which change the state of an LED.  Two kinds of trigger are available, simple
ones which can be added to exising code with minimum disruption and complex
ones for implementing new or more complex functionality.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add the foundations of a new LEDs subsystem.  This patch adds a class which
presents LED devices within sysfs and allows their brightness to be
controlled.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add TIOCL_GETKMSGREDIRECT needed by the userland suspend tool to get the
current value of kmsg_redirect from the kernel so that it can save it and
restore it after resume.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@suse.cz>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix a few memory leaks in drivers/isdn/sc/ioctl.c::sc_ioctl()
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Acked-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Delete two useless kmalloc wrappers and use kmalloc/kzalloc.  Some weird
NULL checks are also simplified.
Signed-off-by: NTobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The "3c59x: use mii_check_media" patch introduced a netif_carrier_off in
vortex_up.  10base2 stoped working because of this.  This is removed.

Tx/Rx reset is back in vortex_up because the 3c900B-Combo stops working after
changing from half duplex to full duplex when Tx/Rx reset is done with
vortex_timer.

Also brought back some mii stuff to be sure that it does not break something
else.

Thanks to Pete Clements <clem@clem.clem-digital.net> for reporting and testing.
Signed-off-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>