One could interpret FC-GS-5 to say that an explicit RNN_ID is required
before RSNN_NN is allowed to succeed, which is why RNN_ID was not obsoleted
along with RPN_ID acording to this document:
ftp://ftp.t11.org/t11/member/fc/gs-5/05-546v2.pdfSigned-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

RPN_ID has been obsolete per FC-GS-5 for several years.  The port name is
registered implicitly as part of FLOGI, and it is undesirable for ports to
change a registered port name using RPN_ID while logged into the fabric.
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The FIP code in libfcoe needed several changes to support NPIV

1) dst_src_addr needs to be managed per-n_port-ID for FPMA fabrics with NPIV
   enabled.  Managing the MAC address is now handled in fcoe, with some slight
   changes to update_mac() and a new get_src_addr() function pointer.

2) The libfc elsct_send() hook is used to setup FCoE specific response
   handlers for FIP encapsulated ELS exchanges.  This lets the FCoE specific
   handling know which VN_Port the exchange is for, and doesn't require
   tracking OX_IDs.  It might be possible to roll back to the full FIP frame
   in these, but for now I've just stashed the contents of the MAC address
   descriptor in the skb context block for later use.  Also, because
   fcoe_elsct_send() just passes control on to fc_elsct_send(), all transmits
   still come through the normal frame_send() path.

3) The NPIV changes added a mutex hold in the keep alive sending, the lport
   mutex is protecting the vport list.  We can't take a mutex from a timer,
   so move the FIP keep alive logic to the link work struct.
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add FDISC ELS handling to libfc and libfcoe, treat it the same as FLOGI where
appropriate.

Add checking for NPIV support in the FLOGI LS_ACC service parameters.
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

NPIV vports are managed in libfc by changing their virtual link state
when the parent N_Ports internal state changes.  The vport link is only
online when the N_Port is in a ready state (logged into the fabric).

vport_state is updated as needed in this patch as well, currently the states
LINKDOWN, INITIALIZING, ACTIVE, DSIABLED, and NO_FABRIC_SUPP are used.

This also changes the fc_host port_state handling to differentiate between
LINKDOWN and OFFLINE.
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Adds a function to create a new VN_Port instances, which share the EM
list with the N_Port, VN_Port lookup by fabric ID when responding to a new
request (otherwise the exchange lookup from the N_Ports EM list is trusted to
return an exchange with a cached lport value for the correct VN_Port),
a pointer to a fc_vport structure for VN_Ports, and flags to indicate if an
N_Port supports NPIV and if the switch/fabric allows it.
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

I'd like to keep basic initialization together with allocation, which means
this can't just be a tail-call to scsi_host_alloc.

This is needed to create a generic libfc host allocation routine for NPIV
VN_Ports, which will share the exchange ID space (through sharing exchange
manager structures) with the parent lport.  In order to clone the exchange
manager list when the lport is allocated, the list head must be initialized
earlier.

Also, update fnic to use the libfc_host_alloc so that later changes do not break
it. (contribution by Joe Eykholt)
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

include/scsi/libfc.h is currently loaded with common code
shared between libfc's sub-modules as well as shared between
libfc and fcoe. Previous patches attempted to move out
non-common code. This patch creates two files for common
libfc routines that will not be shared with fcoe, fnic or
any other LLDs.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This function is never used, let's remove it.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch moves all non-common routines and function prototypes
out of libfc.h and into the appropriate .c files. It makes these
routines 'static' when necessary and removes any unnecessary EXPORT_SYMBOL
statements.

A result of moving the fc_exch_seq_send, fc_seq_els_rsp_send, fc_exch_alloc
and fc_seq_start_next prototypes out of libfc.h is that they were no longer
being imported into fc_exch.c when libfc.h was included. This caused errors
where routines in fc_exch.c were looking for undefined symbols. To fix this
this patch reorganizes fc_seq_alloc, fc_seq_start_next and
fc_seq_start_next_locked. This move also made it so that
fc_seq_start_next_locked did not need to be prototyped at the top of
fc_exch.c.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Move the duplicated code from FC LLDs to SCSI FC transport class.
Acked-by: NJames Smart <james.smart@emulex.com>
Acked-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Acked-by: NAbhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Make scsi_dh_activate() function asynchronous, by taking in two additional
parameters, one is the callback function and the other is the data to call
the callback function with.
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Current FC HBA queue_depth ramp up code depends on last queue
full time. The sdev already  has last_queue_full_time field to
track last queue full time but stored value is truncated by
last four bits.

So this patch updates last_queue_full_time without truncating
last 4 bits to store full value and then updates its only
current usages in scsi_track_queue_full to ignore last four bits
to keep current usages same while also use this field
in added ramp up code.

Adds scsi_handle_queue_ramp_up to ramp up queue_depth on
successful completion of IO. The scsi_handle_queue_ramp_up will
do ramp up on all luns of a target, just same as ramp down done
on all luns on a target.

The ramp up is skipped in case the change_queue_depth is not
supported by LLD or already reached to added max_queue_depth.

Updates added max_queue_depth on every new update to default
queue_depth value.

The ramp up is also skipped if lapsed time since either last
queue ramp up or down is less than LLD specified
queue_ramp_up_period.

Adds queue_ramp_up_period to sysfs but only if change_queue_depth
is supported since ramp up and queue_ramp_up_period is needed only
in case change_queue_depth is supported first.

Initializes queue_ramp_up_period to 120HZ jiffies as initial
default value, it is same as used in existing lpfc and qla2xxx.

-v2
 Combined all ramp code into this single patch.

-v3
 Moves max_queue_depth initialization after slave_configure is
called from after slave_alloc calling done. Also adjusted
max_queue_depth check to skip ramp up if current queue_depth
is >= max_queue_depth.

-v4
 Changes sdev->queue_ramp_up_period unit to ms when using sysfs i/f
to store or show its value.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Tested-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.

This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>

[Vasu.Dev: v2
	Also converted pmcraid_change_queue_depth and then verified
all modules compile  using "make allmodconfig" for any new build
warnings on X86_64.

	Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Timer crashes were caused by freeing a struct fc_rport_priv
with a timer pending, causing the timer facility list to be
corrupted.  This was during FC uplink flap tests with a lot
of targets.

After discovery, we were doing an PLOGI on an rdata that was
in DELETE state but not yet removed from the lookup list.
This moved the rdata from DELETE state to PLOGI state.
If the PLOGI exchange allocation failed and needed to be
retried, the timer scheduling could race with the free
being done by fc_rport_work().

When fc_rport_login() is called on a rport in DELETE state,
move it to a new state RESTART.  In fc_rport_work, when
handling a LOGO, STOPPED or FAILED event, look for restart
state.  In the RESTART case, don't take the rdata off the
list and after the transport remote port is deleted and
exchanges are reset, re-login to the remote port.

Note that the new RESTART state also corrects a problem we
had when re-discovering a port that had moved to DELETE state.
In that case, a new rdata was created, but the old rdata
would do an exchange manager reset affecting the FC_ID
for both the new rdata and old rdata.  With the new state,
the new port isn't logged into until after any old exchanges
are reset.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In case of sequence offload, in fc_fcp_send_data(), the skb_fill_page_info()
called may end up adding more frags to the skb_shinfo(fp_skb(fp))->frags[],
exceeding SKB_MAX_FRAGS, this eventually corrupts the memory. I am adding the
FR_FRAME_SG_LEN back, but as SKB_MAX_FRAGS -1, leaving 1 for our fcoe_eof_crc
page. And send will be broken into multiple large sends if the frame already
contains more frags than skb handle.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Reported-by: NAlex Lyakas <alexl@mellanox.co.il>
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add definitions for UNMAP, WRITE SAME{16,32} and GET LBA STATUS
commands.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch contains changes that allow iscsi_session_setup
to allocate private space for LLD's
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Acked-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Disks formatted with DIF Type 2 reject READ/WRITE 6/10/12/16 commands
when protection is enabled.  Only the 32-byte variants are supported.

Implement support for issusing 32-byte READ/WRITE and enable Type 2
drives in the protection type detection logic.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

So far we have only issued DIF commands if CONFIG_BLK_DEV_INTEGRITY is
enabled.  However, communication between initiator and target should be
independent of protection information DMA.  There are DIF-only host
adapters coming out that will be able to take advantage of this.

Move the relevant DIF bits to sd.c.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The checksum format is orthogonal to whether the protection information
is being passed on beyond the HBA or not.  It is perfectly valid to use
a non-T10 CRC with WRITE_STRIP and READ_INSERT.

Consequently it no longer makes sense to explicitly refer to the
conversion in the protection operation.  Update sd_dif and lpfc
accordingly.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Acked-by: NIhab Hamadi <Ihab.Hamadi@Emulex.Com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

bnx2i currently has a check for if a ep is properly bound, so if
iscsi_queuecommand/xmit_task is called while there is no ep
we will not queue IO.

be2iscsi sends IO from queuecommand/xmit_task like how bnx2i does
and needs a similar test. This patch has us just use the suspend_bit
test for this.

When ep_poll has succeeed iscsid will call conn_bind, the LLD will
then call iscsi_conn_bind which will clear the suspend bit.
When ep_disconnect is called (or if there is a conn error) we set
the suspend bit. For the ep_disconnect case I am adding a helper
in this patch that will take the session lock to make sure
iscsi_queuecommand/xmit_task is not running and it will set
the suspend bit.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

beiscsi does not need the iscsi scsi cmd processing. It does not
even get this info on the completion path. This adds a function
to just update the sequencing numbers and complete a task.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When an RSCN indicates changes to individual remote ports,
don't blindly log them out and then back in.  Instead, determine
whether they're still in the directory, by doing GPN_ID.

If that is successful, call login, which will send ADISC and reverify,
otherwise, call logoff.  Perhaps we should just delete the rport,
not send LOGO, but it seems safer.

Also, fix a possible issue where if a mix of records in the RSCN
cause us to queue disc_ports for disc_single and then we decide
to do full rediscovery, we leak memory for those disc_ports queued.

So, go through the list of disc_ports even if doing full discovery.
Free the disc_ports in any case.  If any of the disc_single() calls
return error, do a full discovery.

The ability to fill in GPN_ID requests was added to fc_ct_fill().
For this, it needs the FC_ID to be passed in as an arg.
The did parameter for fc_elsct_send() is used for that, since the
actual D_DID will always be 0xfffffc for all CT requests so far.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When rport_login is called on an rport that is already thought
to be logged in, use ADISC.  If that fails, redo PLOGI.
This is less disruptive after fabric changes that don't affect
the state of the target.

Implement the sending of ADISC via fc_els_fill.

Add ADISC state to the rport state machine.  This is entered from READY
and returns to READY after successful completion.  If it fails, the rport
is either logged off and deleted or re-does PLOGI.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Improve lport and rport debug messages to indicate whether
the response is LS_ACC, LS_RJT, closed, or timeout.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This moves the remote port lookup for incoming ELS requests into
fc_rport.c, in preparation for handing PLOGI and LOGO from
unknown rports.

This changes the arg to rport_recv_req from an rdata to an lport.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Currently these values are initialized by the callers. This was exposed
by a later patch that adds PLOGI request support. The patch failed to
initialize the new remote port's roles and it caused problems. This patch
has the rport_create routine initialize the identifiers and then the
callers can override them with real values.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

On some switches, an empty zone causes GPN_FT to be rejected
with reason 9 (unable) explanation 7 (FC-4 types not registered),
which causes discovery to be retried endlessly.  Treat this as
just an empty response and consider discovery complete.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When receiving an RSCN, do not log off all rports.  This is
extremely disruptive.  If, after the GPN_FT response, some
rports haven't been listed, delete them.

Add field disc_id to structs fc_rport_priv and fc_disc.
disc_id is an arbitrary serial number used to identify the
rports found by the latest discovery.  This eliminates the need
to go through the rport list when restarting discovery.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Delete unused disc->delay element.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

There was no need to have the discovery status stored in struct fc_disc.

Change fc_disc_done() to take the discovery status as an argument
and just pass it on to the discovery callback.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Don't create a "dummy" remote port to go with fc_rport_priv.

Make the rport truly optional by allocating fc_rport_priv separately
and not requiring a dummy rport to be there if we haven't yet done
fc_remote_port_add().

The fc_rport_libfc_priv remains as a structure attached to the
rport for I/O purposes.

Be sure to hold references on rdata when the lock is dropped in
fc_rport_work().
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Remote ports will become READY more than once after
ADISC is implemented in a later patch.

The event callback that has been called "CREATED" will mean "READY".
Rename it now in preparation for those changes.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Allow a struct fc_rport_priv to have no fc_rport associated with it.
This sets up to remove the need for "rogue" rports.

Add a few fields to fc_rport_priv that are needed before the fc_rport
is created.  These are the ids, maxframe_size, classes, and rport pointer.

Remove the macro PRIV_TO_RPORT().  Just use rdata->rport where appropriate.

To take the place of the get_device()/put_device ops that were used to
hold both the rport and rdata, add a reference count to rdata structures
using kref.  When kref_get decrements the refcount to zero, a new template
function releasing the rdata should be called.  This will take care of
freeing the rdata and releasing the hold on the rport (for now).  After
subsequent patches make the rport truly optional, this release function
will simply free the rdata.

Remove the simple inline function fc_rport_set_name(), which becomes
semanticly ambiguous otherwise.  The caller will set the port_name and
node_name in the rdata->Ids, which will later be copied to the rport
when it its created.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

tt.elsct_send is used by both FCP and by the rport state machine.
After further patches, these two modules will use different
structures for the remote port.

So, change elsct_send to use the FC_ID instead of the fc_rport_priv
as its argument.  It currently only uses the FC_ID anyway.

For CT requests the destination FC_ID is still implicitly 0xfffffc.
After further patches the did arg on CT requests will be used to
specify the FC_ID being inquired about for GPN_ID or other queries.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The rport and discovery modules deal with remote ports
before fc_remote_port_add() can be done, because the
full set of rport identifiers is not known at early stages.

In preparation for splitting the fc_rport/fc_rport_priv allocation,
make fc_rport_priv the primary interface for the remote port and
discovery engines.

The FCP / SCSI layers still deal with fc_rport and
fc_rport_libfc_priv, however.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

These macros introduce extra undesirable semicolons that keep
them from being used in expressions, and they don't protect
against being passed an expression.

Add parens and remove the semicolons.
Signed-off-by: NJoe Eykholt <jeykholt@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>