Patch from Ben Dooks

Enable power management for Simtec Osiris
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Move the decoding of the IRQ_EXT4 and above out of
the entry macro, and into an chained irq handler
as the EXTINT registers move depending on the CPU
being used.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Make the S3C2410 use the same usb clock naming
as the S3C2412
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add basic support for the Samsung/Aiji SMDK2413
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The current S3C2412 has used to moving S3C24XX_
for the generic form of an register has been
moved from the S3C2410.

Fixup S3C2410_EXTINTx and S3C2410_EINFLTx to
S3C24XX_EXTINTx and S3C24XX_EXTINTx

Depends on Patch #3635/1, Patch #3640/1
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The current S3C2412 support has moved to using
S3C24XX_DCLKCON unless the specific DCLKCON is
required (S3C2412_DCLKCON or S3C2410_DKCLKCON)

Move the few places using S3C2410_DCLKCON to
S3C24XX_DCLKCON

Depends on Patch #3635/1
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Serial port support for the on-board UART blocks
on the Samsung S3C2412 and S3C2413 UARTs.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Clock support for the clocks on the Samsung S3C2412
and S3C2413 SoCs. This provides clock enables and
parent selection for all the standard clocks.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Update the clocks with the MPLL clock, and
use it as the parent. Also export these to
the rest of arch/arm/mach-s3c2410
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Select CONFIG_CPU_ARM926 when CONFIG_CPU_S3C2412 is
selected.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add support for the Samsung S3C2412 and S3C2413 range
of SoCs. This patch contains the core identification,
debug macros, and basic register updates to get these
to build.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

The s3c2410 gpio functions have a pair of bugs where
the code is using the pin function definitions instead
of the pin gpio numbers.

Also remove the changelog
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Prevent possible null dereference due to misplaced ;
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (258 commits)
  [libata] conversion to new debug scheme, part 1 of $N
  [PATCH] libata: Add ata_scsi_dev_disabled
  [libata] Add host lock to struct ata_port
  [PATCH] libata: implement per-dev EH action mask eh_info->dev_action[]
  [PATCH] libata-dev: move the CDB-intr DMA blacklisting
  [PATCH] ahci: disable NCQ support on vt8251
  [libata] ahci: add JMicron PCI IDs
  [libata] sata_nv: add PCI IDs
  [libata] ahci: Add NVIDIA PCI IDs.
  [PATCH] libata: convert several bmdma-style controllers to new EH, take #3
  [PATCH] sata_via: convert to new EH, take #3
  [libata] sata_nv: s/spin_lock_irqsave/spin_lock/ in irq handler
  [PATCH] sata_nv: add hotplug support
  [PATCH] sata_nv: convert to new EH
  [PATCH] sata_nv: better irq handlers
  [PATCH] sata_nv: simplify constants
  [PATCH] sata_nv: kill struct nv_host_desc and nv_host
  [PATCH] sata_nv: kill not-working hotplug code
  [libata] Update docs to reflect current driver API
  [PATCH] libata: add host_set->next for legacy two host_sets case, take #3
  ...

arch/ia64/kernel/acpi.c got forgotten when include/acpi/actbl.h
got a cleanup.
Signed-off-by: NTony Luck <tony.luck@intel.com>

My bad.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update hypfs for dhowells API changes.

Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Ingo Oeser <ioe-lkml@rameria.de>
Cc: Joern Engel <joern@wohnheim.fh-wedel.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

drivers/cpufreq/cpufreq_ondemand.c: In function 'do_dbs_timer':
drivers/cpufreq/cpufreq_ondemand.c:374: warning: implicit declaration of function 'lock_cpu_hotplug'
drivers/cpufreq/cpufreq_ondemand.c:381: warning: implicit declaration of function 'unlock_cpu_hotplug'
drivers/cpufreq/cpufreq_conservative.c: In function 'do_dbs_timer':
drivers/cpufreq/cpufreq_conservative.c:425: warning: implicit declaration of function 'lock_cpu_hotplug'
drivers/cpufreq/cpufreq_conservative.c:432: warning: implicit declaration of function 'unlock_cpu_hotplug'

Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Do a safer check for when to enable DMA. Currently we enable ISA DMA
for cases that do not need it, resulting in OOM conditions when ZONE_DMA
runs out of space.
Signed-off-by: NJens Axboe <axboe@suse.de>

They all duplicate macros to check for empty root and/or node, and
clearing a node. So put those in rbtree.h.
Signed-off-by: NJens Axboe <axboe@suse.de>

Otherwise we could be racing with truncate/mapping removal.

Problem found/fixed by Nick Piggin <npiggin@suse.de>, logic rewritten
by me.
Signed-off-by: NJens Axboe <axboe@suse.de>

- Remember to set ->last_sector so that the cfq_choose_req() logic
  works correctly.

- Remove redundant call to cfq_choose_req()
Signed-off-by: NJens Axboe <axboe@suse.de>

This is a collection of patches that greatly improve CFQ performance
in some circumstances.

- Change the idling logic to only kick in after a request is done and we
  are deciding what to do. Before the idling included the request service
  time, so it was hard to adjust. Now it's true think/idle time.

- Take advantage of TCQ/NCQ/queueing for seeky sync workloads, but keep
  it in control for sync and sequential (or close to) workloads.

- Expire queues immediately and move on to other busy queues, if we are
  not going to idle after the current one finishes.

- Don't rearm idle timer if there are no busy queues. Just leave the
  system idle.
Signed-off-by: NJens Axboe <axboe@suse.de>

Patch originally from Vasily Tarasov <vtaras@sw.ru>

If you set io-priority of process 1 using sys_ioprio_set system call by
another process 2 (like ionice do), then cfq_init_prio_data() function
sets priority of process 2 (current) on queue of process 1 and clears
the flag, that designates change of ioprio.  So the process  1 will work
like with priority of process 2.

I propose not to call cfq_init_prio_data() on io-priority change, but
only mark queue as queue with changed prority.  Every time when new
request comes cfq-scheduler checks for this flag and atomaticaly changes
priority of queue to new value.
Signed-off-by: NJens Axboe <axboe@suse.de>

Signed-off-by: NJens Axboe <axboe@suse.de>

This saves 8 bytes of data in 64-bit archs.
Signed-off-by: NJens Axboe <axboe@suse.de>

The IDE power management can just use the ->end_io_data member to store
it's data.
Signed-off-by: NJens Axboe <axboe@suse.de>

A process flag to indicate whether we are doing sync io is incredibly
ugly. It also causes performance problems when one does a lot of async
io and then proceeds to sync it. Part of the io will go out as async,
and the other part as sync. This causes a disconnect between the
previously submitted io and the synced io. For io schedulers such as CFQ,
this will cause us lost merges and suboptimal behaviour in scheduling.

Remove PF_SYNCWRITE completely from the fsync/msync paths, and let
the O_DIRECT path just directly indicate that the writes are sync
by using WRITE_SYNC instead.
Signed-off-by: NJens Axboe <axboe@suse.de>

We cannot update them if the user changes nr_requests, so don't
set it in the first place. The gains are pretty questionable as
well. The batching loss has been shown to decrease throughput.
Signed-off-by: NJens Axboe <axboe@suse.de>

We already drop the refcount in elevator_exit(), and as
we're setting 'e' to NULL, we'll never take that branch anyway.
Finally, as 'e' is a local var that isn't referenced afterwards,
setting it to NULL is pointless.
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NJens Axboe <axboe@suse.de>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJens Axboe <axboe@suse.de>

The queue lock can be taken from interrupts so it must always be taken with
irq disabling primitives.  Some primitives already verify this.
blk_start_queue() is called under this lock, so interrupts must be
disabled.

Also document this requirement clearly in blk_init_queue(), where the queue
spinlock is set.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJens Axboe <axboe@suse.de>

Use hlist instead of list_head for request hashtable in deadline-iosched
and as-iosched. It also can remove the flag to know hashed or unhashed.
Signed-off-by: NAkinobu Mita <mita@miraclelinux.com>
Signed-off-by: NJens Axboe <axboe@suse.de>

 block/as-iosched.c       |   45 +++++++++++++++++++--------------------------
 block/deadline-iosched.c |   39 ++++++++++++++++-----------------------
 2 files changed, 35 insertions(+), 49 deletions(-)

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [NET]: Require CAP_NET_ADMIN to create tuntap devices.
  [NET]: fix net-core kernel-doc
  [TCP]: Move inclusion of <linux/dmaengine.h> to correct place in <linux/tcp.h>
  [IPSEC]: Handle GSO packets
  [NET]: Added GSO toggle
  [NET]: Add software TSOv4
  [NET]: Add generic segmentation offload
  [NET]: Merge TSO/UFO fields in sk_buff
  [NET]: Prevent transmission after dev_deactivate
  [IPV6] ADDRCONF: Fix default source address selection without CONFIG_IPV6_PRIVACY
  [IPV6]: Fix source address selection.
  [NET]: Avoid allocating skb in skb_pad

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (65 commits)
  ACPI: suppress power button event on S3 resume
  ACPI: resolve merge conflict between sem2mutex and processor_perflib.c
  ACPI: use for_each_possible_cpu() instead of for_each_cpu()
  ACPI: delete newly added debugging macros in processor_perflib.c
  ACPI: UP build fix for bugzilla-5737
  Enable P-state software coordination via _PDC
  P-state software coordination for speedstep-centrino
  P-state software coordination for acpi-cpufreq
  P-state software coordination for ACPI core
  ACPI: create acpi_thermal_resume()
  ACPI: create acpi_fan_suspend()/acpi_fan_resume()
  ACPI: pass pm_message_t from acpi_device_suspend() to root_suspend()
  ACPI: create acpi_device_suspend()/acpi_device_resume()
  ACPI: replace spin_lock_irq with mutex for ec poll mode
  ACPI: Allow a WAN module enable/disable on a Thinkpad X60.
  sem2mutex: acpi, acpi_link_lock
  ACPI: delete unused acpi_bus_drivers_lock
  sem2mutex: drivers/acpi/processor_perflib.c
  ACPI add ia64 exports to build acpi_memhotplug as a module
  ACPI: asus_acpi_init(): propagate correct return value
  ...

Manual resolve of conflicts in:

	arch/i386/kernel/cpu/cpufreq/acpi-cpufreq.c
	arch/i386/kernel/cpu/cpufreq/speedstep-centrino.c
	include/acpi/processor.h

Update the sparse documentation to omit the -Wbitwise flag example (as it
is now passed by default), and document the kernel defines to enable
endianness checking.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

While writing a version of losetup, I ran into the problem that the loop
device was returning total garbage.

It turns out the problem was that this losetup was only issuing the
LOOP_SET_FD ioctl and not issuing a subsequent LOOP_SET_STATUS ioctl.  This
losetup didn't have any special status to set, so it left out the call.

The deeper cause is that loop_set_fd sets the transfer function to NULL,
which causes no transfer to happen lo_do_transfer.

This patch fixes the problem by setting transfer to transfer_none in
loop_set_fd.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Sometimes partitions claim to be larger than the reported capacity of a
disk device.  This patch makes the kernel warn about those partitions.

We still permit these patitions to be used.  Quoting Andries Brouwer
<Andries.Brouwer@cwi.nl>:

 Case 1: The kernel is mistaken about the size of the disk.  (There are
 commands to clip a disk to a certain capacity, there are jumpers to tell a
 disk that it should report a certain capacity etc.  Usually this is because
 of BIOS bugs.  In bad cases the machine will crash in the BIOS and hence fail
 to boot if the disk reports full capacity.) In such cases actually accessing
 the blocks of the partition may work fine, or may work fine after running an
 unclip utility.  I wrote "setmax" some years ago precisely for this reason.

 Case 2: There was a messy partition table (maybe just a rounding error) but
 the actual filesystem on the partition is contained in the physical disk.
 Now using the filesystem goes without problem.

 Case 3: Both partition and filesystem extend beyond the end of the disk.  In
 forensic or debugging situations one often uses a copy of the start of a
 disk.  Now access beyond the end gives an expected I/O error.
Signed-off-by: NMike Miller <mike.miller@hp.com>
Signed-off-by: NStephen Cameron <steve.cameron@hp.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: N"Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>