Get some more reasonable information reported back out to ethtool
for the different types of connections supported.

Change-Id: I57b153f86b9cdd04ad7cb5bf7d1c45873c196a7a
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

A freshly allocated skb starts with timestamps clear.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The SFC9100 family has only one clock per controller, shared by all
functions.  Therefore only create a clock device under the primary
function, and make all other functions refer to the primary's clock
device.

Since PTP functionality is limited to port 0 and PF 0 on the earlier
SFN[56]322F boards, and we also set the primary flag for that
function, we can make the creation of a clock device conditional only
on this flag.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The primary function of an EF10 controller will share its clock
device with other functions in the same domain (which we call
secondary functions).  To this end, we need to associate functions
on the same controller.

We do not control probe order, so allow primary and secondary
functions to appear in any order.  Maintain global lists of all
primary functions and of unassociated secondary functions,
and a list of secondary functions on each primary function.

Use the VPD serial number to tell whether functions are part of the
same controller.  VPD will not be readable by virtual functions, so
this may need to be revisited later.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Original version by Stuart Hodgson.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The EF10 firmware can optionally insert RX timestamps in the packet
prefix.  These only include the clock minor value.  We must also
enable periodic time sync events on each event queue which provide
the high bits of the clock value.

[bwh: Combined and rebased several changes.
 Added the above description and some sanity checks for inline vs
 separate timestamps.
 Changed efx_rx_skb_attach_timestamp() to read the packet prefix
 from the skb head area.]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We can potentially pull the entire packet contents into the head area
and then free the page it was in.  In order to read an inline
timestamp safely, we need to copy the prefix into the head area as
well.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

I added efx_ptp_get_mode() to avoid moving the definition for
efx_ptp_data, since the current PTP mode is needed for
siena.c:siena_set_ptp_hwtstamp.

[bwh: Also move the rx_filters mask, and add kernel-doc]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The clock minor tick on the SFC9100 family is 2^-27 s, not 1 ns.
There are also various pipeline delays which we need to correct for
when interpreting timestamps.

We query the firmware for the clock format and corrections at run-time.

[bwh: Combined and rebased several changes]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We'll be sharing clocks between multiple functions with their own MAC
addresses.  The name field is now documented as 'A short "friendly
name" to identify the clock ...' and '... not meant to be a unique
id.'  So use the name 'sfc'.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We need a dedicated channel on Siena to ensure we can match up
the separate RX and timestamp events for each PTP packet.  We won't
do this for EF10 as timestamps are delivered inline.

Pass a channel index of 0 to MC_CMD_PTP_OP_ENABLE when there is no
dedicated channel.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The MC firmware will return error MC_CMD_ERR_ENOSPC if filter
insertion fails due to lack of resources.  The net driver's filter
implementation for Falcon-architecture returns EBUSY.  They should
behave consistently, so for EF10 change ENOSPC to EBUSY.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

efx_flush_all() is a really misleading name - it has nothing to do
with e.g. flushing DMA queues.  Since it's called immediately after
efx_stop_port() and is highly dependent on what that does, combine
the two functions.

Update comments to explain what this is doing a little better.
Also update an related and erroneous comment in efx_start_port().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Split each of efx_mcdi_rpc, efx_mcdi_rpc_finish, and efx_mcdi_rpc_async into
a normal and a _quiet version; made the former log MCDI errors with
netif_err (and include the raw MCDI error code), and the latter never log
them at all.  Changed various callers; any where some errors are expected
(but others are not) call the _quiet version and then if necessary log the
MCDI error themselves.  Said logging is done by new efx_mcdi_display_error.

Callers of efx_mcdi_rpc*_quiet functions which may want to log the error
need to ensure that their outbuf is big enough to hold an MCDI error; to
this end, they now use MCDI_DECLARE_BUF_OUT_OR_ERR, which always allocates
at least 8 bytes.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Add units to the "Sensor reports condition X for raw value Y" messages.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We don't directly control RX ingress on Siena or any later
controllers, and so we cannot prevent packets from entering the RX
datapath while the RX queues are not set up.  This results in
the hardware incrementing RX_NODESC_DROP_CNT, but it's not an
error and we should not include it in error stats.

When bringing an interface up or down, pull (or wait for) stats and
count the number of packets that were dropped while the interface was
down.  Subtract this from the reported RX dropped count.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The addition of RX event merging support means we don't reliably
detect dropped RX events now.  Currently we will only detect them if
the previous event for the RX queue had the CONT bit set.

Only accept RX completion events as merged if the
GET_CAPABILITIES_OUT_RX_BATCHING bit is set in datapath_caps (which it
won't be for the low-latency datapath) and the CONT bit is not set on
the event.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

To run BISTs the MC goes down in to a special mode where it will only
respond to MCDI from the testing PF, and TX, RX and event queues are
torn down. Other PFs get a message as it goes down to tell them it's
going down.

When the other PFs get this message, they check the soft status
register to tell when the MC has rebooted after BIST mode and they can
start recovery.

[bwh: Convert the test result to 1 or -1 as for earlier NICs]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Commit c45f812f ('8390 : Replace ei_debug with msg_enable/NETIF_MSG_*
feature') ended up moving the printout of version[] from something that
will be compiled out due to defines, to something that is now evaluated
at runtime.

That means that what always used to be an access to an __initdata string
from non-__init code started showing up as a section mismatch when it
didn't before.

All other 8390 versions skip __initdata on the version string, and
starting to annotate the whole chain of callers with __init seems like
more churn than it's worth on this driver, so remove it from etherh.c as well.

Fixes: c45f812f ('8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature')
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Minor fix for printk format of a phys_addr_t, and the switch of two local
functions to static since they're not used outside of the file.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only used locally. Found by sparse.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Silences the below warnings when building with ARM_LPAE enabled, which
gives longer dma_addr_t by default:

drivers/net/ethernet/ti/davinci_cpdma.c: In function 'cpdma_desc_pool_create':
drivers/net/ethernet/ti/davinci_cpdma.c:182:3: warning: passing argument 3 of 'dma_alloc_attrs' from incompatible pointer type [enabled by default]
drivers/net/ethernet/ti/davinci_cpdma.c: In function 'desc_phys':
drivers/net/ethernet/ti/davinci_cpdma.c:222:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/net/ethernet/ti/davinci_cpdma.c:223:8: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed the shared ei_debug variable. Replaced it by adding u32 msg_enable to
the private struct ei_device. Now each 8390 ethernet instance has a per-device
logging variable.

Changed older style printk() calls to more canonical forms.

Tested on: ne, ne2k-pci, smc-ultra, and wd hardware.

V4.0
- Substituted pr_info() and pr_debug() for printk() KERN_INFO and KERN_DEBUG

V3.0
- Checked for cases where pr_cont() was most appropriate choice.
- Changed module parameter from 'debug' to 'msg_enable' because debug was
no longer the best description.

V2.0
- Changed netif_msg_(drv|probe|ifdown|rx_err|tx_err|tx_queued|intr|rx_status|hw)
to netif_(dbg|info|warn|err) where possible.
Signed-off-by: NMatthew Whitehead <tedheadster@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this bgmac_adjust_link didn't know it should re-initialize MAC
state. This led to the MAC not working after if down & up routine.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When adjusting the link speed, the target frequency is determined by a
'swith (LINK_SPEED)' statement, that assigns the target rate only for
valid and expected LINK_SPEED values. This incomplete switch statement
leads to the following build warning:
     drivers/net/ethernet/cadence/macb.c: In function 'macb_handle_link_change':
  >> drivers/net/ethernet/cadence/macb.c:241:14: warning: 'rate' may be used uninitialized in this function [-Wmaybe-uninitialized]
        netdev_warn(dev, "unable to generate target frequency: %ld Hz\n",
                   ^
     drivers/net/ethernet/cadence/macb.c:215:13: note: 'rate' was declared here
       long ferr, rate, rate_rounded;

Fixing this by bailing out of that function in the switch's default case
before the rate variable is used.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust the ethernet clock according to the negotiated link speed.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the device managed interface to request the IRQ, simplifying error
paths.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>