Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[jejb: fixup checkpatch error]
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

We need to return QLA_FUNCTION_TIMEOUT immediately otherwise we mess up the
mailbox command state machine.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Stop unconditional completion of mailbox commands issued in interrupt mode during firmware hang.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If there is an error creating multiple response queues then we need to revert
the request queue mapping back to request queue 0.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This function can wait for 5min under certain scenarios. One of them is when
the port is down from switch and bus reset is issued. The bus reset used to
wait for 5 minutes for the loop and upper layer callers used to hang and give
stack trace because of getting stuck for 120 sec. It is legacy code that was
used when the driver used to do queuing of the commands.
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

_scsih_smart_predicted_fault is called in an interrupt and therefore
must allocate memory using GFP_ATOMIC.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

* git://git.samba.org/sfrench/cifs-2.6:
  cifs: check for NULL last_entry before calling cifs_save_resume_key
  cifs: attempt to freeze while looping on a receive attempt
  cifs: Fix sparse warning when calling cifs_strtoUCS
  CIFS: Add descriptions to the brlock cache functions

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, efi: Calling __pa() with an ioremap()ed address is invalid
  x86, hpet: Immediately disable HPET timer 1 if rtc irq is masked
  x86/intel_mid: Kconfig select fix
  x86/intel_mid: Fix the Kconfig for MID selection

* 'spi/for-3.2' of git://git.pengutronix.de/git/wsa/linux-2.6:
  spi/gpio: fix section mismatch warning
  spi/fsl-espi: disable CONFIG_SPI_FSL_ESPI=m build
  spi/nuc900: Include linux/module.h
  spi/ath79: fix compile error due to missing include

* 'for-linus' of git://neil.brown.name/md:
  md: raid5 crash during degradation
  md/raid5: never wait for bad-block acks on failed device.
  md: ensure new badblocks are handled promptly.
  md: bad blocks shouldn't cause a Blocked status on a Faulty device.
  md: take a reference to mddev during sysfs access.
  md: refine interpretation of "hold_active == UNTIL_IOCTL".
  md/lock: ensure updates to page_attrs are properly locked.

* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  arch/tile: use new generic {enable,disable}_percpu_irq() routines
  drivers/net/ethernet/tile: use skb_frag_page() API
  asm-generic/unistd.h: support new process_vm_{readv,write} syscalls
  arch/tile: fix double-free bug in homecache_free_pages()
  arch/tile: add a few #includes and an EXPORT to catch up with kernel changes.

* 'iommu/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  MAINTAINERS: Update amd-iommu F: patterns
  iommu/amd: Fix typo in kernel-parameters.txt
  iommu/msm: Fix compile error in mach-msm/devices-iommu.c
  Fix comparison using wrong pointer variable in dma debug code

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - Fix lost speaker volume controls
  ALSA: hda/realtek - Create "Bass Speaker" for two speaker pins
  ALSA: hda/realtek - Don't create extra controls with channel suffix
  ALSA: hda - Fix remaining VREF mute-LED NID check in post-3.1 changes
  ALSA: hda - Fix GPIO LED setup for IDT 92HD75 codecs
  ASoC: Provide a more complete DMA driver stub
  ASoC: Remove references to corgi and spitz from machine driver document
  ASoC: Make SND_SOC_MX27VIS_AIC32X4 depend on I2C
  ASoC: Fix dependency for SND_SOC_RAUMFELD and SND_PXA2XX_SOC_HX4700
  ASoC: uda1380: Return proper error in uda1380_modinit failure path
  ASoC: kirkwood: Make SND_KIRKWOOD_SOC_OPENRD and SND_KIRKWOOD_SOC_T5325 depend on I2C
  ASoC: Mark WM8994 ADC muxes as virtual
  ALSA: hda/realtek - Fix Oops in alc_mux_select()
  ALSA: sis7019 - give slow codecs more time to reset

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Do no try to schedule task events if there are none
  lockdep, kmemcheck: Annotate ->lock in lockdep_init_map()
  perf header: Use event_name() to get an event name
  perf stat: Failure with "Operation not supported"

In order to safely dereference current->real_parent inside an
rcu_read_lock, we need an rcu_dereference.
Signed-off-by: NMandeep Singh Baines <msb@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Modify initialization of PCIe capability registers in Tsi721 mport driver:
 - change Completion Timeout value to avoid unexpected data transfer
   aborts during intensive traffic.
 - replace hardcoded offset of PCIe capability block by making it use the
   common function.

This patch is applicable to kernel versions starting from 3.2-rc1.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Bug fix for Tsi721 RapidIO mport driver: Tsi721 supports four RapidIO
mailboxes (MBOX0 - MBOX3) as defined by RapidIO specification.  Mailbox
resources has to be properly reported to allow use of all available
mailboxes (initial version reports only MBOX0).

This patch is applicable to kernel versions staring from 3.2-rc1.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace the pair dma_alloc_coherent()+memset() with the new
dma_zalloc_coherent() added by Andrew Morton for kernel version 3.2
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since commit a25cac51 ("proc: Consider NO_HZ when printing idle and
iowait times") we are reporting idle/io_wait time also while a CPU is
tickless.  We rely on get_{idle,iowait}_time functions to retrieve
proper data.

These functions, however, use usecs_to_cputime to translate micro
seconds time to cputime64_t.  This is just an alias to usecs_to_jiffies
which reduces the data type from u64 to unsigned int and also checks
whether the given parameter overflows jiffies_to_usecs(MAX_JIFFY_OFFSET)
and returns MAX_JIFFY_OFFSET in that case.

When we overflow depends on CONFIG_HZ but especially for CONFIG_HZ_300
it is quite low (1431649781) so we are getting MAX_JIFFY_OFFSET for
>3000s! until we overflow unsigned int.  Just for reference
CONFIG_HZ_100 has an overflow window around 20s, CONFIG_HZ_250 ~8s and
CONFIG_HZ_1000 ~2s.

This results in a bug when people saw [h]top going mad reporting 100%
CPU usage even though there was basically no CPU load.  The reason was
simply that /proc/stat stopped reporting idle/io_wait changes (and
reported MAX_JIFFY_OFFSET) and so the only change happening was for user
system time.

Let's use nsecs_to_jiffies64 instead which doesn't reduce the precision
to 32b type and it is much more appropriate for cumulative time values
(unlike usecs_to_jiffies which intended for timeout calculations).
Signed-off-by: NMichal Hocko <mhocko@suse.cz>
Tested-by: NArtem S. Tashkinov <t.artem@mailcity.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit f5252e00 ("mm: avoid null pointer access in vm_struct via
/proc/vmallocinfo") adds newly allocated vm_structs to the vmlist after
it is fully initialised.  Unfortunately, it did not check that
__vmalloc_area_node() successfully populated the area.  In the event of
allocation failure, the vmalloc area is freed but the pointer to freed
memory is inserted into the vmlist leading to a a crash later in
get_vmalloc_info().

This patch adds a check for ____vmalloc_area_node() failure within
__vmalloc_node_range.  It does not use "goto fail" as in the previous
error path as a warning was already displayed by __vmalloc_area_node()
before it called vfree in its failure path.

Credit goes to Luciano Chavez for doing all the real work of identifying
exactly where the problem was.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reported-by: NLuciano Chavez <lnx1138@linux.vnet.ibm.com>
Tested-by: NLuciano Chavez <lnx1138@linux.vnet.ibm.com>
Reviewed-by: NRik van Riel <riel@redhat.com>
Acked-by: NDavid Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org>		[3.1.x+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

setup_zone_migrate_reserve() expects that zone->start_pfn starts at
pageblock_nr_pages aligned pfn otherwise we could access beyond an
existing memblock resulting in the following panic if
CONFIG_HOLES_IN_ZONE is not configured and we do not check pfn_valid:

  IP: [<c02d331d>] setup_zone_migrate_reserve+0xcd/0x180
  *pdpt = 0000000000000000 *pde = f000ff53f000ff53
  Oops: 0000 [#1] SMP
  Pid: 1, comm: swapper Not tainted 3.0.7-0.7-pae #1 VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform
  EIP: 0060:[<c02d331d>] EFLAGS: 00010006 CPU: 0
  EIP is at setup_zone_migrate_reserve+0xcd/0x180
  EAX: 000c0000 EBX: f5801fc0 ECX: 000c0000 EDX: 00000000
  ESI: 000c01fe EDI: 000c01fe EBP: 00140000 ESP: f2475f58
  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
  Process swapper (pid: 1, ti=f2474000 task=f2472cd0 task.ti=f2474000)
  Call Trace:
  [<c02d389c>] __setup_per_zone_wmarks+0xec/0x160
  [<c02d3a1f>] setup_per_zone_wmarks+0xf/0x20
  [<c08a771c>] init_per_zone_wmark_min+0x27/0x86
  [<c020111b>] do_one_initcall+0x2b/0x160
  [<c086639d>] kernel_init+0xbe/0x157
  [<c05cae26>] kernel_thread_helper+0x6/0xd
  Code: a5 39 f5 89 f7 0f 46 fd 39 cf 76 40 8b 03 f6 c4 08 74 32 eb 91 90 89 c8 c1 e8 0e 0f be 80 80 2f 86 c0 8b 14 85 60 2f 86 c0 89 c8 <2b> 82 b4 12 00 00 c1 e0 05 03 82 ac 12 00 00 8b 00 f6 c4 08 0f
  EIP: [<c02d331d>] setup_zone_migrate_reserve+0xcd/0x180 SS:ESP 0068:f2475f58
  CR2: 00000000000012b4

We crashed in pageblock_is_reserved() when accessing pfn 0xc0000 because
highstart_pfn = 0x36ffe.

The issue was introduced in 3.0-rc1 by 6d3163ce ("mm: check if any page
in a pageblock is reserved before marking it MIGRATE_RESERVE").

Make sure that start_pfn is always aligned to pageblock_nr_pages to
ensure that pfn_valid s always called at the start of each pageblock.
Architectures with holes in pageblocks will be correctly handled by
pfn_valid_within in pageblock_is_reserved.
Signed-off-by: NMichal Hocko <mhocko@suse.cz>
Signed-off-by: NMel Gorman <mgorman@suse.de>
Tested-by: NDang Bo <bdang@vmware.com>
Reviewed-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Arve Hjnnevg <arve@android.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>	[3.0+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Avoid unlocking and unlocked page if we failed to lock it.
Signed-off-by: NHillf Danton <dhillf@gmail.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 70b50f94 ("mm: thp: tail page refcounting fix") keeps all
page_tail->_count zero at all times.  But the current kernel does not
set page_tail->_count to zero if a 1GB page is utilized.  So when an
IOMMU 1GB page is used by KVM, it wil result in a kernel oops because a
tail page's _count does not equal zero.

  kernel BUG at include/linux/mm.h:386!
  invalid opcode: 0000 [#1] SMP
  Call Trace:
    gup_pud_range+0xb8/0x19d
    get_user_pages_fast+0xcb/0x192
    ? trace_hardirqs_off+0xd/0xf
    hva_to_pfn+0x119/0x2f2
    gfn_to_pfn_memslot+0x2c/0x2e
    kvm_iommu_map_pages+0xfd/0x1c1
    kvm_iommu_map_memslots+0x7c/0xbd
    kvm_iommu_map_guest+0xaa/0xbf
    kvm_vm_ioctl_assigned_device+0x2ef/0xa47
    kvm_vm_ioctl+0x36c/0x3a2
    do_vfs_ioctl+0x49e/0x4e4
    sys_ioctl+0x5a/0x7c
    system_call_fastpath+0x16/0x1b
  RIP  gup_huge_pud+0xf2/0x159
Signed-off-by: NYouquan Song <youquan.song@intel.com>
Reviewed-by: NAndrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With the 3.2-rc kernel, IOMMU 2M pages in KVM works.  But when I tried
to use IOMMU 1GB pages in KVM, I encountered an oops and the 1GB page
failed to be used.

The root cause is that 1GB page allocation calls gup_huge_pud() while 2M
page calls gup_huge_pmd.  If compound pages are used and the page is a
tail page, gup_huge_pmd() increases _mapcount to record tail page are
mapped while gup_huge_pud does not do that.

So when the mapped page is relesed, it will result in kernel oops
because the page is not marked mapped.

This patch add tail process for compound page in 1GB huge page which
keeps the same process as 2M page.

Reproduce like:
1. Add grub boot option: hugepagesz=1G hugepages=8
2. mount -t hugetlbfs -o pagesize=1G hugetlbfs /dev/hugepages
3. qemu-kvm -m 2048 -hda os-kvm.img -cpu kvm64 -smp 4 -mem-path /dev/hugepages
	-net none -device pci-assign,host=07:00.1

  kernel BUG at mm/swap.c:114!
  invalid opcode: 0000 [#1] SMP
  Call Trace:
    put_page+0x15/0x37
    kvm_release_pfn_clean+0x31/0x36
    kvm_iommu_put_pages+0x94/0xb1
    kvm_iommu_unmap_memslots+0x80/0xb6
    kvm_assign_device+0xba/0x117
    kvm_vm_ioctl_assigned_device+0x301/0xa47
    kvm_vm_ioctl+0x36c/0x3a2
    do_vfs_ioctl+0x49e/0x4e4
    sys_ioctl+0x5a/0x7c
    system_call_fastpath+0x16/0x1b
  RIP  put_compound_page+0xd4/0x168
Signed-off-by: NYouquan Song <youquan.song@intel.com>
Reviewed-by: NAndrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 4f2a8d3c ("printk: Fix console_sem vs logbuf_lock unlock race")
introduced another silly bug where we would want to acquire an already
held lock.  Avoid this.
Reported-by: NAndrea Arcangeli <aarcange@redhat.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

More players joined to memory cgroup developments and Johannes' great work
changed internal design of memory cgroup dramatically.  And he will do
more works.  Michal Hokko did many bug fixes and know memory cgroup very
well.  Daisuke Nishimura helped us very much but he seems busy now.
Thanks to his works.
Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: NMichal Hocko <mhocko@suse.cz>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Acked-by: NDaisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If an error occurs after the clock is enabled, the enable/disable state
can become unbalanced.
Signed-off-by: NJonghwan Choi <jhbird.choi@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Small clean-up for my CREDITS entry; the GPG fingerprint was not up to
date, so I fixed other details at the same time too.
Signed-off-by: NKees Cook <kees@outflux.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

khugepaged can sometimes cause suspend to fail, requiring that the user
retry the suspend operation.

Use wait_event_freezable_timeout() instead of
schedule_timeout_interruptible() to avoid missing freezer wakeups.  A
try_to_freeze() would have been needed in the khugepaged_alloc_hugepage
tight loop too in case of the allocation failing repeatedly, and
wait_event_freezable_timeout will provide it too.

khugepaged would still freeze just fine by trying again the next minute
but it's better if it freezes immediately.
Reported-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NAndrea Arcangeli <aarcange@redhat.com>
Tested-by: NJiri Slaby <jslaby@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: "Rafael J. Wysocki" <rjw@suse.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the error message "directives may not be used inside a macro argument"
which appears when the kernel is compiled for the cris architecture.
Signed-off-by: NClaudio Scordino <claudio@evidence.eu.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use atomic-long operations instead of looping around cmpxchg().

[akpm@linux-foundation.org: massage atomic.h inclusions]
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A shrinker function can return -1, means that it cannot do anything
without a risk of deadlock.  For example prune_super() does this if it
cannot grab a superblock refrence, even if nr_to_scan=0.  Currently we
interpret this -1 as a ULONG_MAX size shrinker and evaluate `total_scan'
according to this.  So the next time around this shrinker can cause
really big pressure.  Let's skip such shrinkers instead.

Also make total_scan signed, otherwise the check (total_scan < 0) below
never works.
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 29b68415 ("x86: amd_iommu: move to drivers/iommu/")
moved the files, update the patterns.

CC: Ohad Ben-Cohen <ohad@wizery.com>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

If we encounter an efi_memory_desc_t without EFI_MEMORY_WB set
in ->attribute we currently call set_memory_uc(), which in turn
calls __pa() on a potentially ioremap'd address.

On CONFIG_X86_32 this is invalid, resulting in the following
oops on some machines:

  BUG: unable to handle kernel paging request at f7f22280
  IP: [<c10257b9>] reserve_ram_pages_type+0x89/0x210
  [...]

  Call Trace:
   [<c104f8ca>] ? page_is_ram+0x1a/0x40
   [<c1025aff>] reserve_memtype+0xdf/0x2f0
   [<c1024dc9>] set_memory_uc+0x49/0xa0
   [<c19334d0>] efi_enter_virtual_mode+0x1c2/0x3aa
   [<c19216d4>] start_kernel+0x291/0x2f2
   [<c19211c7>] ? loglevel+0x1b/0x1b
   [<c19210bf>] i386_start_kernel+0xbf/0xc8

A better approach to this problem is to map the memory region
with the correct attributes from the start, instead of modifying
it after the fact. The uncached case can be handled by
ioremap_nocache() and the cached by ioremap_cache().

Despite first impressions, it's not possible to use
ioremap_cache() to map all cached memory regions on
CONFIG_X86_64 because EFI_RUNTIME_SERVICES_DATA regions really
don't like being mapped into the vmalloc space, as detailed in
the following bug report,

	https://bugzilla.redhat.com/show_bug.cgi?id=748516

Therefore, we need to ensure that any EFI_RUNTIME_SERVICES_DATA
regions are covered by the direct kernel mapping table on
CONFIG_X86_64. To accomplish this we now map E820_RESERVED_EFI
regions via the direct kernel mapping with the initial call to
init_memory_mapping() in setup_arch(), whereas previously these
regions wouldn't be mapped if they were after the last E820_RAM
region until efi_ioremap() was called. Doing it this way allows
us to delete efi_ioremap() completely.
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@console-pimps.orgSigned-off-by: NIngo Molnar <mingo@elte.hu>

Prior to commit eaf35b1e, cifs_save_resume_key had some NULL pointer
checks at the top. It turns out that at least one of those NULL
pointer checks is needed after all.

When the LastNameOffset in a FIND reply appears to be beyond the end of
the buffer, CIFSFindFirst and CIFSFindNext will set srch_inf.last_entry
to NULL. Since eaf35b1e, the code will now oops in this situation.

Fix this by having the callers check for a NULL last entry pointer
before calling cifs_save_resume_key. No change is needed for the
call site in cifs_readdir as it's not reachable with a NULL
current_entry pointer.

This should fix:

    https://bugzilla.redhat.com/show_bug.cgi?id=750247

Cc: stable@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Reported-by: NAdam G. Metzler <adamgmetzler@gmail.com>
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NSteve French <smfrench@gmail.com>