On Thu, May 28, 2009 at 10:59 AM, Mark Brown <broonie@opensource.wolfsonmicro.com> wrote:
> On Thu, May 28, 2009 at 07:15:16AM +0200, Philipp Zabel wrote:
>> The V3 regulator can be configured with an external resistor
>> connected to the feedback pin (R24 in the data sheet) to
>> increase the voltage range.
>>
>> For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
>> V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
>>
>> Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
>
> Looks good.
>
> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Thanks, but it turns out I hit a 32 bit integer overflow in
the gain calculation. I'd like to mend that with the following
patch. Now max_uV could be increased up to 4.294 V, enough to
charge LiPo cells.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The V3 regulator can be configured with an external resistor
connected to the feedback pin (R24 in the data sheet) to
increase the voltage range.

For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

lp3971_i2c_remove' referenced in section `.data' of drivers/built-in.o:
defined in discarded section `.devexit.text' of drivers/built-in.o
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This patch adds regulator drivers for National Semiconductors LP3971 PMIC.
This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low
drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface.
Reviewed-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Several of the regulator drivers didn't have MODULE_ALIAS so couldn't be
auto loaded. Add the MODULE_ALIAS in case they do get built as modules.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Regulators need to be available early in init in order to allow them
to be available for consumers when requested. This is generally done
by registering them at subsys_initcall() time but not all regulator
drivers have done that. Convert these drivers to do so in order to
mimimise future support.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This patch fixes the follwing build failure on powerpc:-

> Today's linux-next build (powerpc allyesconfig) failed like this:
>
> drivers/regulator/userspace-consumer.c:43: error: conflicting types
> for 'show_state'
> include/linux/sched.h:273: note: previous definition of 'show_state'
> was here
>
> Caused by commit 5defa2bce704ca4151cfe24e4297aa7797cafd22 ("regulator:
> add userspace-consumer driver") which I have reverted for today.
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The userspace-consumer driver allows control of voltage and current
regulator state from userspace. This is required for fine-grained
power management of devices that are completely controller by userspace
applications, e.g. a GPS transciever connected to a serial port.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The Maxim 1586 regulator is a voltage regulator with 2
voltage outputs, specially suitable for Marvell PXA
chips. One output is in the range of required VCC_CORE by
the PXA27x chips, the other in the VCC_USIM required as well
by PXA27x chips.

The chip is controlled through the I2C bus.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (53 commits)
  .gitignore: ignore *.lzma files
  kbuild: add generic --set-str option to scripts/config
  kbuild: simplify argument loop in scripts/config
  kbuild: handle non-existing options in scripts/config
  kallsyms: generalize text region handling
  kallsyms: support kernel symbols in Blackfin on-chip memory
  documentation: make version fix
  kbuild: fix a compile warning
  gitignore: Add GNU GLOBAL files to top .gitignore
  kbuild: fix delay in setlocalversion on readonly source
  README: fix misleading pointer to the defconf directory
  vmlinux.lds.h update
  kernel-doc: cleanup perl script
  Improve vmlinux.lds.h support for arch specific linker scripts
  kbuild: fix headers_exports with boolean expression
  kbuild/headers_check: refine extern check
  kbuild: fix "Argument list too long" error for "make headers_check",
  ignore *.patch files
  Remove bashisms from scripts
  menu: fix embedded menu presentation
  ...

Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  mlx4_core: Don't double-free IRQs when falling back from MSI-X to INTx
  IB/mthca: Don't double-free IRQs when falling back from MSI-X to INTx
  IB/mlx4: Add strong ordering to local inval and fast reg work requests
  IB/ehca: Remove superfluous bitmasks from QP control block
  RDMA/cxgb3: Limit fast register size based on T3 limitations
  RDMA/cxgb3: Report correct port state and MTU
  mlx4_core: Add module parameter for number of MTTs per segment
  IB/mthca: Add module parameter for number of MTTs per segment
  RDMA/nes: Fix off-by-one bugs in reset_adapter_ne020() and init_serdes()
  infiniband: Remove void casts
  IB/ehca: Increment version number
  IB/ehca: Remove unnecessary memory operations for userspace queue pairs
  IB/ehca: Fall back to vmalloc() for big allocations
  IB/ehca: Replace vmalloc() with kmalloc() for queue allocation

* git://git.kernel.org/pub/scm/linux/kernel/git/jaswinder/headers-check-2.6:
  headers_check fix: mn10300, setup.h
  headers_check fix: mn10300, ptrace.h

Fix recent fusion driver kernel-doc fatal error and warnings.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Eric.Moore@lsi.com
Cc: support@lsi.com
Cc: DL-MPTFusionLinux@lsi.com
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In addition to KT_DEAD which has limited support for diacriticals,
there is KT_DEAD2 that can support 256 criticals, so let's advertise
it in <linux/keyboard.h>.

This lets userland know abut the drivers/char/keyboard.c function
k_dead2, which supports more than the few trivial ones that k_dead
supports.
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMichal Marek <mmarek@suse.cz>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Signed-off-by: NMichal Marek <mmarek@suse.cz>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

If an option does not exist in .config, set it at the end of the file.
Signed-off-by: NMichal Marek <mmarek@suse.cz>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (25 commits)
  atmel-mci: add MCI2 register definitions
  atmel-mci: Integrate AT91 specific definition in header file
  tmio_mmc: allow compilation for ASIC3
  mmc_block: do not DMA to stack
  sdhci: Print ADMA status and pointer on debug
  tmio_mmc: fix clock setup
  tmio_mmc: map SD control registers after enabling the MFD cell
  tmio_mmc: correct probe return value for num_resources != 3
  tmio_mmc: don't use set_irq_type
  tmio_mmc: add bus_shift support
  MFD,mmc: tmio_mmc: make HCLK configurable
  mmc_spi: don't use EINVAL for possible transmission errors
  cb710: more cleanup for the DEBUG case.
  sdhci: platform driver for SDHCI
  mxcmmc: remove frequency workaround
  cb710: handle DEBUG define in Makefile
  cb710: add missing parenthesis
  cb710: fix printk format string
  mmc: Driver for CB710/720 memory card reader (MMC part)
  pxamci: add regulator support.
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (31 commits)
  trivial: remove the trivial patch monkey's name from SubmittingPatches
  trivial: Fix a typo in comment of addrconf_dad_start()
  trivial: usb: fix missing space typo in doc
  trivial: pci hotplug: adding __init/__exit macros to sgi_hotplug
  trivial: Remove the hyphen from git commands
  trivial: fix ETIMEOUT -> ETIMEDOUT typos
  trivial: Kconfig: .ko is normally not included in module names
  trivial: SubmittingPatches: fix typo
  trivial: Documentation/dell_rbu.txt: fix typos
  trivial: Fix Pavel's address in MAINTAINERS
  trivial: ftrace:fix description of trace directory
  trivial: unnecessary (void*) cast removal in sound/oss/msnd.c
  trivial: input/misc: Fix typo in Kconfig
  trivial: fix grammo in bus_for_each_dev() kerneldoc
  trivial: rbtree.txt: fix rb_entry() parameters in sample code
  trivial: spelling fix in ppc code comments
  trivial: fix typo in bio_alloc kernel doc
  trivial: Documentation/rbtree.txt: cleanup kerneldoc of rbtree.txt
  trivial: Miscellaneous documentation typo fixes
  trivial: fix typo milisecond/millisecond for documentation and source comments.
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: fix inverted wheel for bluetooth version of apple mighty mouse
  HID: no more reinitializtion is needed in post_reset
  HID: hidraw -- fix comment about accepted devices
  HID: Multitouch support for the N-Trig touchscreen
  HID: add new multitouch and digitizer contants
  HID: autocentering support for Logitech Force 3D Pro
  HID: fix hid-ff drivers so that devices work even without ff support
  HID: force feedback support for SmartJoy PLUS PS2/USB adapter
  HID: Wacom Graphire Bluetooth driver
  HID: autocentering support for Logitech G25 Racing Wheel

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5545/2: add flush_kernel_dcache_page() for ARM

Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

The Blackfin arch has a discontiguous .text layout due to having on-chip
instruction memory and no virtual memory support.  As such, we need to
add explicit checks for these additional .text regions.
Signed-off-by: NRobin Getz <robin.getz@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
  MAINTAINERS: EB110ATX is not ebsa110
  MAINTAINERS: update Eric Miao's email address and status
  fb: add support of LCD display controller on pxa168/910 (base layer)
  [ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
  [ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
  [ARM] 5544/1: Trust PrimeCell resource sizes
  [ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
  [ARM] pxa/sharpsl_pm: drop set_irq_type calls
  [ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
  [ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
  [ARM] sa1100: remove unused collie_pm.c
  [ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
  [ARM] 5550/1: Add default configure file for w90p910 platform
  [ARM] 5549/1: Add clock api for w90p910 platform.
  [ARM] 5548/1: Add gpio api for w90p910 platform
  [ARM] 5551/1: Add multi-function pin api for w90p910 platform.
  [ARM] Make ARM_VIC_NR depend on ARM_VIC
  [ARM] 5546/1: ARM PL022 SSP/SPI driver v3
  ARM: OMAP4: SMP: Update defconfig for OMAP4430
  ARM: OMAP4: SMP: Enable SMP support for OMAP4430
  ...

The Makefiles in the build directories use the internal make variable
MAKEFILE_LIST which is available from make 3.80 only.  (The patch would be
valid back to 2.6.25)
Signed-off-by: NAdam Lackorzynski <adam@os.inf.tu-dresden.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

gcc-4.4.1:

 HOSTCC  scripts/basic/fixdep
scripts/basic/fixdep.c: In function 'traps':
scripts/basic/fixdep.c:377: warning: dereferencing type-punned pointer will break strict-aliasing rules
scripts/basic/fixdep.c:379: warning: dereferencing type-punned pointer will break strict-aliasing rules

(Apparently -fno-strict-aliasing will fix this too)
Signed-off-by: NWANG Cong <amwang@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice.  Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time.  This is the same bug that was reported in ib_mthca by Yinghai
Lu <yhlu.kernel@gmail.com>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Ignore GPATH, GRTAGS, GSYMS, and GTAGS generated by GNU GLOBAL.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Do not update index on read only media.
Idea published by Christian Kujau <lists@nerdbynature.de>.

Cc: Nico Schottelius <nico@ikn.schottelius.org>
Cc: Christian Kujau <lists@nerdbynature.de>

Signed-off-by: NPatrick Ringl <patrick_@freenet.de>
Cc: Arnd Bergmann <arnd@arndb.de>

Updated after review by Tim Abbott.
- Use HEAD_TEXT_SECTION
- Drop use of section-names.h and delete file
- Introduce EXIT_CALL

Deleting section-names.h required a few simple
updates of init.h
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Tim Abbott <tabbott@ksplice.com>

Without this, the default implementation is a no op which is completely
wrong with a VIVT cache, and usage of sg_copy_buffer() produces
unpredictable results.
Tested-by: NSebastian Andrzej Siewior <bigeasy@breakpoint.cc>

CC: stable@kernel.org
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Conflicts:
	arch/arm/Makefile
Updates:
	arch/arm/mach-u300/core.c
	arch/arm/mach-u300/timer.c

Merge branch 'for-rmk' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel