- 13 2月, 2019 40 次提交
-
-
由 Dan Carpenter 提交于
[ Upstream commit 00670cb8a73b10b10d3c40f045c15411715e4465 ] This function can't succeed if dp->pl is NULL. It will Oops inside the call to return phylink_ethtool_get_eee(dp->pl, e); Fixes: 1be52e97 ("dsa: slave: eee: Allow ports to use phylink") Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com> Reviewed-by: NVivien Didelot <vivien.didelot@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Marc Zyngier 提交于
[ Upstream commit c8101f7729daee251f4f6505f9d135ec08e1342f ] Creating a macvtap on a DSA-backed interface results in the following splat when lockdep is enabled: [ 19.638080] IPv6: ADDRCONF(NETDEV_CHANGE): lan0: link becomes ready [ 23.041198] device lan0 entered promiscuous mode [ 23.043445] device eth0 entered promiscuous mode [ 23.049255] [ 23.049557] ============================================ [ 23.055021] WARNING: possible recursive locking detected [ 23.060490] 5.0.0-rc3-00013-g56c857a1b8d3 #118 Not tainted [ 23.066132] -------------------------------------------- [ 23.071598] ip/2861 is trying to acquire lock: [ 23.076171] 00000000f61990cb (_xmit_ETHER){+...}, at: dev_set_rx_mode+0x1c/0x38 [ 23.083693] [ 23.083693] but task is already holding lock: [ 23.089696] 00000000ecf0c3b4 (_xmit_ETHER){+...}, at: dev_uc_add+0x24/0x70 [ 23.096774] [ 23.096774] other info that might help us debug this: [ 23.103494] Possible unsafe locking scenario: [ 23.103494] [ 23.109584] CPU0 [ 23.112093] ---- [ 23.114601] lock(_xmit_ETHER); [ 23.117917] lock(_xmit_ETHER); [ 23.121233] [ 23.121233] *** DEADLOCK *** [ 23.121233] [ 23.127325] May be due to missing lock nesting notation [ 23.127325] [ 23.134315] 2 locks held by ip/2861: [ 23.137987] #0: 000000003b766c72 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x338/0x4e0 [ 23.146231] #1: 00000000ecf0c3b4 (_xmit_ETHER){+...}, at: dev_uc_add+0x24/0x70 [ 23.153757] [ 23.153757] stack backtrace: [ 23.158243] CPU: 0 PID: 2861 Comm: ip Not tainted 5.0.0-rc3-00013-g56c857a1b8d3 #118 [ 23.166212] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT) [ 23.172843] Call trace: [ 23.175358] dump_backtrace+0x0/0x188 [ 23.179116] show_stack+0x14/0x20 [ 23.182524] dump_stack+0xb4/0xec [ 23.185928] __lock_acquire+0x123c/0x1860 [ 23.190048] lock_acquire+0xc8/0x248 [ 23.193724] _raw_spin_lock_bh+0x40/0x58 [ 23.197755] dev_set_rx_mode+0x1c/0x38 [ 23.201607] dev_set_promiscuity+0x3c/0x50 [ 23.205820] dsa_slave_change_rx_flags+0x5c/0x70 [ 23.210567] __dev_set_promiscuity+0x148/0x1e0 [ 23.215136] __dev_set_rx_mode+0x74/0x98 [ 23.219167] dev_uc_add+0x54/0x70 [ 23.222575] macvlan_open+0x170/0x1d0 [ 23.226336] __dev_open+0xe0/0x160 [ 23.229830] __dev_change_flags+0x16c/0x1b8 [ 23.234132] dev_change_flags+0x20/0x60 [ 23.238074] do_setlink+0x2d0/0xc50 [ 23.241658] __rtnl_newlink+0x5f8/0x6e8 [ 23.245601] rtnl_newlink+0x50/0x78 [ 23.249184] rtnetlink_rcv_msg+0x360/0x4e0 [ 23.253397] netlink_rcv_skb+0xe8/0x130 [ 23.257338] rtnetlink_rcv+0x14/0x20 [ 23.261012] netlink_unicast+0x190/0x210 [ 23.265043] netlink_sendmsg+0x288/0x350 [ 23.269075] sock_sendmsg+0x18/0x30 [ 23.272659] ___sys_sendmsg+0x29c/0x2c8 [ 23.276602] __sys_sendmsg+0x60/0xb8 [ 23.280276] __arm64_sys_sendmsg+0x1c/0x28 [ 23.284488] el0_svc_common+0xd8/0x138 [ 23.288340] el0_svc_handler+0x24/0x80 [ 23.292192] el0_svc+0x8/0xc This looks fairly harmless (no actual deadlock occurs), and is fixed in a similar way to c6894dec ("bridge: fix lockdep addr_list_lock false positive splat") by putting the addr_list_lock in its own lockdep class. Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com> Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
[ Upstream commit 53bc8d2af08654659abfadfd3e98eb9922ff787c ] During sendmsg() a cloned skb is saved via dp83640_txtstamp() in ->tx_queue. After the NIC sends this packet, the PHY will reply with a timestamp for that TX packet. If the cable is pulled at the right time I don't see that packet. It might gets flushed as part of queue shutdown on NIC's side. Once the link is up again then after the next sendmsg() we enqueue another skb in dp83640_txtstamp() and have two on the list. Then the PHY will send a reply and decode_txts() attaches it to the first skb on the list. No crash occurs since refcounting works but we are one packet behind. linuxptp/ptp4l usually closes the socket and opens a new one (in such a timeout case) so those "stale" replies never get there. However it does not resume normal operation anymore. Purge old skbs in decode_txts(). Fixes: cb646e2b ("ptp: Added a clock driver for the National Semiconductor PHYTER.") Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: NKurt Kanzenbach <kurt@linutronix.de> Acked-by: NRichard Cochran <richardcochran@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Bart Van Assche 提交于
[ Upstream commit fc42a689c4c097859e5bd37b5ea11b60dc426df6 ] The test_insert_dup() function from lib/test_rhashtable.c passes a pointer to a stack object to rhltable_init(). Allocate the hash table dynamically to avoid that the following is reported with object debugging enabled: ODEBUG: object (ptrval) is on stack (ptrval), but NOT annotated. WARNING: CPU: 0 PID: 1 at lib/debugobjects.c:368 __debug_object_init+0x312/0x480 Modules linked in: EIP: __debug_object_init+0x312/0x480 Call Trace: ? debug_object_init+0x1a/0x20 ? __init_work+0x16/0x30 ? rhashtable_init+0x1e1/0x460 ? sched_clock_cpu+0x57/0xe0 ? rhltable_init+0xb/0x20 ? test_insert_dup+0x32/0x20f ? trace_hardirqs_on+0x38/0xf0 ? ida_dump+0x10/0x10 ? jhash+0x130/0x130 ? my_hashfn+0x30/0x30 ? test_rht_init+0x6aa/0xab4 ? ida_dump+0x10/0x10 ? test_rhltable+0xc5c/0xc5c ? do_one_initcall+0x67/0x28e ? trace_hardirqs_off+0x22/0xe0 ? restore_all_kernel+0xf/0x70 ? trace_hardirqs_on_thunk+0xc/0x10 ? restore_all_kernel+0xf/0x70 ? kernel_init_freeable+0x142/0x213 ? rest_init+0x230/0x230 ? kernel_init+0x10/0x110 ? schedule_tail_wrapper+0x9/0xc ? ret_from_fork+0x19/0x24 Cc: Thomas Graf <tgraf@suug.ch> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: NBart Van Assche <bvanassche@acm.org> Acked-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
[ Upstream commit 7596175e99b3d4bce28022193efd954c201a782a ] In case of IPv6 pkts, ipv4_csum_ok is 0. Because of this, driver does not set skb->ip_summed. So IPv6 rx checksum is not offloaded. Signed-off-by: NGovindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Eric Dumazet 提交于
[ Upstream commit 9b1f19d810e92d6cdc68455fbc22d9f961a58ce1 ] Similarly to commit 276bdb82 ("dccp: check ccid before dereferencing") it is wise to test for a NULL ccid. kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] PREEMPT SMP KASAN CPU: 1 PID: 16 Comm: ksoftirqd/1 Not tainted 5.0.0-rc3+ #37 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:ccid_hc_tx_parse_options net/dccp/ccid.h:205 [inline] RIP: 0010:dccp_parse_options+0x8d9/0x12b0 net/dccp/options.c:233 Code: c5 0f b6 75 b3 80 38 00 0f 85 d6 08 00 00 48 b9 00 00 00 00 00 fc ff df 48 8b 45 b8 4c 8b b8 f8 07 00 00 4c 89 f8 48 c1 e8 03 <80> 3c 08 00 0f 85 95 08 00 00 48 b8 00 00 00 00 00 fc ff df 4d 8b kobject: 'loop5' (0000000080f78fc1): kobject_uevent_env RSP: 0018:ffff8880a94df0b8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8880858ac723 RCX: dffffc0000000000 RDX: 0000000000000100 RSI: 0000000000000007 RDI: 0000000000000001 RBP: ffff8880a94df140 R08: 0000000000000001 R09: ffff888061b83a80 R10: ffffed100c370752 R11: ffff888061b83a97 R12: 0000000000000026 R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8880ae700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f0defa33518 CR3: 000000008db5e000 CR4: 00000000001406e0 kobject: 'loop5' (0000000080f78fc1): fill_kobj_path: path = '/devices/virtual/block/loop5' DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: dccp_rcv_state_process+0x2b6/0x1af6 net/dccp/input.c:654 dccp_v4_do_rcv+0x100/0x190 net/dccp/ipv4.c:688 sk_backlog_rcv include/net/sock.h:936 [inline] __sk_receive_skb+0x3a9/0xea0 net/core/sock.c:473 dccp_v4_rcv+0x10cb/0x1f80 net/dccp/ipv4.c:880 ip_protocol_deliver_rcu+0xb6/0xa20 net/ipv4/ip_input.c:208 ip_local_deliver_finish+0x23b/0x390 net/ipv4/ip_input.c:234 NF_HOOK include/linux/netfilter.h:289 [inline] NF_HOOK include/linux/netfilter.h:283 [inline] ip_local_deliver+0x1f0/0x740 net/ipv4/ip_input.c:255 dst_input include/net/dst.h:450 [inline] ip_rcv_finish+0x1f4/0x2f0 net/ipv4/ip_input.c:414 NF_HOOK include/linux/netfilter.h:289 [inline] NF_HOOK include/linux/netfilter.h:283 [inline] ip_rcv+0xed/0x620 net/ipv4/ip_input.c:524 __netif_receive_skb_one_core+0x160/0x210 net/core/dev.c:4973 __netif_receive_skb+0x2c/0x1c0 net/core/dev.c:5083 process_backlog+0x206/0x750 net/core/dev.c:5923 napi_poll net/core/dev.c:6346 [inline] net_rx_action+0x76d/0x1930 net/core/dev.c:6412 __do_softirq+0x30b/0xb11 kernel/softirq.c:292 run_ksoftirqd kernel/softirq.c:654 [inline] run_ksoftirqd+0x8e/0x110 kernel/softirq.c:646 smpboot_thread_fn+0x6ab/0xa10 kernel/smpboot.c:164 kthread+0x357/0x430 kernel/kthread.c:246 ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352 Modules linked in: ---[ end trace 58a0ba03bea2c376 ]--- RIP: 0010:ccid_hc_tx_parse_options net/dccp/ccid.h:205 [inline] RIP: 0010:dccp_parse_options+0x8d9/0x12b0 net/dccp/options.c:233 Code: c5 0f b6 75 b3 80 38 00 0f 85 d6 08 00 00 48 b9 00 00 00 00 00 fc ff df 48 8b 45 b8 4c 8b b8 f8 07 00 00 4c 89 f8 48 c1 e8 03 <80> 3c 08 00 0f 85 95 08 00 00 48 b8 00 00 00 00 00 fc ff df 4d 8b RSP: 0018:ffff8880a94df0b8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8880858ac723 RCX: dffffc0000000000 RDX: 0000000000000100 RSI: 0000000000000007 RDI: 0000000000000001 RBP: ffff8880a94df140 R08: 0000000000000001 R09: ffff888061b83a80 R10: ffffed100c370752 R11: ffff888061b83a97 R12: 0000000000000026 R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8880ae700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f0defa33518 CR3: 0000000009871000 CR4: 00000000001406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Signed-off-by: NEric Dumazet <edumazet@google.com> Reported-by: Nsyzbot <syzkaller@googlegroups.com> Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Eduardo Valentin 提交于
commit 03334ba8b425b2ad275c8f390cf83c7b081c3095 upstream. Avoid warnings like this: thermal_hwmon.h:29:1: warning: ‘thermal_remove_hwmon_sysfs’ defined but not used [-Wunused-function] thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz) Fixes: 0dd88793 ("thermal: hwmon: move hwmon support to single file") Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NEduardo Valentin <edubezval@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Eric Sandeen 提交于
commit 7d048df4e9b05ba89b74d062df59498aa81f3785 upstream. xfs_btree_sblock_verify_crc is a bool so should not be returning a failaddr_t; worse, if xfs_log_check_lsn fails it returns __this_address which looks like a boolean true (i.e. success) to the caller. (interestingly xfs_btree_lblock_verify_crc doesn't have the issue) Signed-off-by: NEric Sandeen <sandeen@redhat.com> Reviewed-by: NChristoph Hellwig <hch@lst.de> Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NLuis Chamberlain <mcgrof@kernel.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Darrick J. Wong 提交于
commit a579121f94aba4e8bad1a121a0fad050d6925296 upstream. In commit e53c4b59, I *tried* to teach xfs to force writeback when we fzero/fpunch right up to EOF so that if EOF is in the middle of a page, the post-EOF part of the page gets zeroed before we return to userspace. Unfortunately, I missed the part where PAGE_MASK is ~(PAGE_SIZE - 1), which means that we totally fail to zero if we're fpunching and EOF is within the first page. Worse yet, the same PAGE_MASK thinko plagues the filemap_write_and_wait_range call, so we'd initiate writeback of the entire file, which (mostly) masked the thinko. Drop the tricky PAGE_MASK and replace it with correct usage of PAGE_SIZE and the proper rounding macros. Fixes: e53c4b59 ("xfs: ensure post-EOF zeroing happens after zeroing part of a file") Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com> Reviewed-by: NDave Chinner <dchinner@redhat.com> Reviewed-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NLuis Chamberlain <mcgrof@kernel.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Ye Yin 提交于
commit de7243057e7cefa923fa5f467c0f1ec24eef41d2 upsream. When project is set, we should use inode limit minus the used count Signed-off-by: NYe Yin <dbyin@tencent.com> Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NLuis Chamberlain <mcgrof@kernel.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Dave Chinner 提交于
commit 9230a0b65b47fe6856c4468ec0175c4987e5bede upstream. Long saga. There have been days spent following this through dead end after dead end in multi-GB event traces. This morning, after writing a trace-cmd wrapper that enabled me to be more selective about XFS trace points, I discovered that I could get just enough essential tracepoints enabled that there was a 50:50 chance the fsx config would fail at ~115k ops. If it didn't fail at op 115547, I stopped fsx at op 115548 anyway. That gave me two traces - one where the problem manifested, and one where it didn't. After refining the traces to have the necessary information, I found that in the failing case there was a real extent in the COW fork compared to an unwritten extent in the working case. Walking back through the two traces to the point where the CWO fork extents actually diverged, I found that the bad case had an extra unwritten extent in it. This is likely because the bug it led me to had triggered multiple times in those 115k ops, leaving stray COW extents around. What I saw was a COW delalloc conversion to an unwritten extent (as they should always be through xfs_iomap_write_allocate()) resulted in a /written extent/: xfs_writepage: dev 259:0 ino 0x83 pgoff 0x17000 size 0x79a00 offset 0 length 0 xfs_iext_remove: dev 259:0 ino 0x83 state RC|LF|RF|COW cur 0xffff888247b899c0/2 offset 32 block 152 count 20 flag 1 caller xfs_bmap_add_extent_delay_real xfs_bmap_pre_update: dev 259:0 ino 0x83 state RC|LF|RF|COW cur 0xffff888247b899c0/1 offset 1 block 4503599627239429 count 31 flag 0 caller xfs_bmap_add_extent_delay_real xfs_bmap_post_update: dev 259:0 ino 0x83 state RC|LF|RF|COW cur 0xffff888247b899c0/1 offset 1 block 121 count 51 flag 0 caller xfs_bmap_add_ex Basically, Cow fork before: 0 1 32 52 +H+DDDDDDDDDDDD+UUUUUUUUUUU+ PREV RIGHT COW delalloc conversion allocates: 1 32 +uuuuuuuuuuuu+ NEW And the result according to the xfs_bmap_post_update trace was: 0 1 32 52 +H+wwwwwwwwwwwwwwwwwwwwwwww+ PREV Which is clearly wrong - it should be a merged unwritten extent, not an unwritten extent. That lead me to look at the LEFT_FILLING|RIGHT_FILLING|RIGHT_CONTIG case in xfs_bmap_add_extent_delay_real(), and sure enough, there's the bug. It takes the old delalloc extent (PREV) and adds the length of the RIGHT extent to it, takes the start block from NEW, removes the RIGHT extent and then updates PREV with the new extent. What it fails to do is update PREV.br_state. For delalloc, this is always XFS_EXT_NORM, while in this case we are converting the delayed allocation to unwritten, so it needs to be updated to XFS_EXT_UNWRITTEN. This LF|RF|RC case does not do this, and so the resultant extent is always written. And that's the bug I've been chasing for a week - a bmap btree bug, not a reflink/dedupe/copy_file_range bug, but a BMBT bug introduced with the recent in core extent tree scalability enhancements. Signed-off-by: NDave Chinner <dchinner@redhat.com> Reviewed-by: NChristoph Hellwig <hch@lst.de> Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NLuis Chamberlain <mcgrof@kernel.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Dave Chinner 提交于
commit d43aaf1685aa471f0593685c9f54d53e3af3cf3f upstream. When retrying a failed inode or dquot buffer, xfs_buf_resubmit_failed_buffers() clears all the failed flags from the inde/dquot log items. In doing so, it also drops all the reference counts on the buffer that the failed log items hold. This means it can drop all the active references on the buffer and hence free the buffer before it queues it for write again. Putting the buffer on the delwri queue takes a reference to the buffer (so that it hangs around until it has been written and completed), but this goes bang if the buffer has already been freed. Hence we need to add the buffer to the delwri queue before we remove the failed flags from the log items attached to the buffer to ensure it always remains referenced during the resubmit process. Reported-by: NJosef Bacik <josef@toxicpanda.com> Signed-off-by: NDave Chinner <dchinner@redhat.com> Reviewed-by: NChristoph Hellwig <hch@lst.de> Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NLuis Chamberlain <mcgrof@kernel.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Brian Foster 提交于
commit 59e4293149106fb92530f8e56fa3992d8548c5e6 upstream. Page writeback indirectly handles shared extents via the existence of overlapping COW fork blocks. If COW fork blocks exist, writeback always performs the associated copy-on-write regardless if the underlying blocks are actually shared. If the blocks are shared, then overlapping COW fork blocks must always exist. fstests shared/010 reproduces a case where a buffered write occurs over a shared block without performing the requisite COW fork reservation. This ultimately causes writeback to the shared extent and data corruption that is detected across md5 checks of the filesystem across a mount cycle. The problem occurs when a buffered write lands over a shared extent that crosses an extent size hint boundary and that also happens to have a partial COW reservation that doesn't cover the start and end blocks of the data fork extent. For example, a buffered write occurs across the file offset (in FSB units) range of [29, 57]. A shared extent exists at blocks [29, 35] and COW reservation already exists at blocks [32, 34]. After accommodating a COW extent size hint of 32 blocks and the existing reservation at offset 32, xfs_reflink_reserve_cow() allocates 32 blocks of reservation at offset 0 and returns with COW reservation across the range of [0, 34]. The associated data fork extent is still [29, 35], however, which isn't fully covered by the COW reservation. This leads to a buffered write at file offset 35 over a shared extent without associated COW reservation. Writeback eventually kicks in, performs an overwrite of the underlying shared block and causes the associated data corruption. Update xfs_reflink_reserve_cow() to accommodate the fact that a delalloc allocation request may not fully cover the extent in the data fork. Trim the data fork extent appropriately, just as is done for shared extent boundaries and/or existing COW reservations that happen to overlap the start of the data fork extent. This prevents shared/010 failures due to data corruption on reflink enabled filesystems. Signed-off-by: NBrian Foster <bfoster@redhat.com> Reviewed-by: NChristoph Hellwig <hch@lst.de> Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NLuis Chamberlain <mcgrof@kernel.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Dave Chinner 提交于
commit 837514f7a4ca4aca06aec5caa5ff56d33ef06976 upstream. generic/070 on 64k block size filesystems is failing with a verifier corruption on writeback or an attribute leaf block: [ 94.973083] XFS (pmem0): Metadata corruption detected at xfs_attr3_leaf_verify+0x246/0x260, xfs_attr3_leaf block 0x811480 [ 94.975623] XFS (pmem0): Unmount and run xfs_repair [ 94.976720] XFS (pmem0): First 128 bytes of corrupted metadata buffer: [ 94.978270] 000000004b2e7b45: 00 00 00 00 00 00 00 00 3b ee 00 00 00 00 00 00 ........;....... [ 94.980268] 000000006b1db90b: 00 00 00 00 00 81 14 80 00 00 00 00 00 00 00 00 ................ [ 94.982251] 00000000433f2407: 22 7b 5c 82 2d 5c 47 4c bb 31 1c 37 fa a9 ce d6 "{\.-\GL.1.7.... [ 94.984157] 0000000010dc7dfb: 00 00 00 00 00 81 04 8a 00 0a 18 e8 dd 94 01 00 ................ [ 94.986215] 00000000d5a19229: 00 a0 dc f4 fe 98 01 68 f0 d8 07 e0 00 00 00 00 .......h........ [ 94.988171] 00000000521df36c: 0c 2d 32 e2 fe 20 01 00 0c 2d 58 65 fe 0c 01 00 .-2.. ...-Xe.... [ 94.990162] 000000008477ae06: 0c 2d 5b 66 fe 8c 01 00 0c 2d 71 35 fe 7c 01 00 .-[f.....-q5.|.. [ 94.992139] 00000000a4a6bca6: 0c 2d 72 37 fc d4 01 00 0c 2d d8 b8 f0 90 01 00 .-r7.....-...... [ 94.994789] XFS (pmem0): xfs_do_force_shutdown(0x8) called from line 1453 of file fs/xfs/xfs_buf.c. Return address = ffffffff815365f3 This is failing this check: end = ichdr.freemap[i].base + ichdr.freemap[i].size; if (end < ichdr.freemap[i].base) >>>>> return __this_address; if (end > mp->m_attr_geo->blksize) return __this_address; And from the buffer output above, the freemap array is: freemap[0].base = 0x00a0 freemap[0].size = 0xdcf4 end = 0xdd94 freemap[1].base = 0xfe98 freemap[1].size = 0x0168 end = 0x10000 freemap[2].base = 0xf0d8 freemap[2].size = 0x07e0 end = 0xf8b8 These all look valid - the block size is 0x10000 and so from the last check in the above verifier fragment we know that the end of freemap[1] is valid. The problem is that end is declared as: uint16_t end; And (uint16_t)0x10000 = 0. So we have a verifier bug here, not a corruption. Fix the verifier to use uint32_t types for the check and hence avoid the overflow. Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=201577Signed-off-by: NDave Chinner <dchinner@redhat.com> Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NLuis Chamberlain <mcgrof@kernel.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Christophe JAILLET 提交于
commit 132bf6723749f7219c399831eeb286dbbb985429 upstream. In this function, once 'buf' has been allocated, we unconditionally return 0. However, 'error' is set to some error codes in several error handling paths. Before commit 232b5194 ("xfs: simplify the xfs_getbmap interface") this was not an issue because all error paths were returning directly, but now that some cleanup at the end may be needed, we must propagate the error code. Fixes: 232b5194 ("xfs: simplify the xfs_getbmap interface") Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: NChristoph Hellwig <hch@lst.de> Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com> Signed-off-by: NLuis Chamberlain <mcgrof@kernel.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Christoph Hellwig 提交于
commit 96987eea537d6ccd98704a71958f9ba02da80843 upstream. We need to make sure we have no outstanding COW blocks before we swap extents, as there is nothing preventing us from having preallocated COW delalloc on either inode that swapext is called on. That case can easily be reproduced by running generic/324 in always_cow mode: [ 620.760572] XFS: Assertion failed: tip->i_delayed_blks == 0, file: fs/xfs/xfs_bmap_util.c, line: 1669 [ 620.761608] ------------[ cut here ]------------ [ 620.762171] kernel BUG at fs/xfs/xfs_message.c:102! [ 620.762732] invalid opcode: 0000 [#1] SMP PTI [ 620.763272] CPU: 0 PID: 24153 Comm: xfs_fsr Tainted: G W 4.19.0-rc1+ #4182 [ 620.764203] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.1-1 04/01/2014 [ 620.765202] RIP: 0010:assfail+0x20/0x28 [ 620.765646] Code: 31 ff e8 83 fc ff ff 0f 0b c3 48 89 f1 41 89 d0 48 c7 c6 48 ca 8d 82 48 89 fa 38 [ 620.767758] RSP: 0018:ffffc9000898bc10 EFLAGS: 00010202 [ 620.768359] RAX: 0000000000000000 RBX: ffff88012f14ba40 RCX: 0000000000000000 [ 620.769174] RDX: 00000000ffffffc0 RSI: 000000000000000a RDI: ffffffff828560d9 [ 620.769982] RBP: ffff88012f14b300 R08: 0000000000000000 R09: 0000000000000000 [ 620.770788] R10: 000000000000000a R11: f000000000000000 R12: ffffc9000898bc98 [ 620.771638] R13: ffffc9000898bc9c R14: ffff880130b5e2b8 R15: ffff88012a1fa2a8 [ 620.772504] FS: 00007fdc36e0fbc0(0000) GS:ffff88013ba00000(0000) knlGS:0000000000000000 [ 620.773475] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 620.774168] CR2: 00007fdc3604d000 CR3: 0000000132afc000 CR4: 00000000000006f0 [ 620.774978] Call Trace: [ 620.775274] xfs_swap_extent_forks+0x2a0/0x2e0 [ 620.775792] xfs_swap_extents+0x38b/0xab0 [ 620.776256] xfs_ioc_swapext+0x121/0x140 [ 620.776709] xfs_file_ioctl+0x328/0xc90 [ 620.777154] ? rcu_read_lock_sched_held+0x50/0x60 [ 620.777694] ? xfs_iunlock+0x233/0x260 [ 620.778127] ? xfs_setattr_nonsize+0x3be/0x6a0 [ 620.778647] do_vfs_ioctl+0x9d/0x680 [ 620.779071] ? ksys_fchown+0x47/0x80 [ 620.779552] ksys_ioctl+0x35/0x70 [ 620.780040] __x64_sys_ioctl+0x11/0x20 [ 620.780530] do_syscall_64+0x4b/0x190 [ 620.780927] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 620.781467] RIP: 0033:0x7fdc364d0f07 [ 620.781900] Code: b3 66 90 48 8b 05 81 5f 2c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 28 [ 620.784044] RSP: 002b:00007ffe2a766038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 620.784896] RAX: ffffffffffffffda RBX: 0000000000000025 RCX: 00007fdc364d0f07 [ 620.785667] RDX: 0000560296ca2fc0 RSI: 00000000c0c0586d RDI: 0000000000000005 [ 620.786398] RBP: 0000000000000025 R08: 0000000000001200 R09: 0000000000000000 [ 620.787283] R10: 0000000000000432 R11: 0000000000000246 R12: 0000000000000005 [ 620.788051] R13: 0000000000000000 R14: 0000000000001000 R15: 0000000000000006 [ 620.788927] Modules linked in: [ 620.789340] ---[ end trace 9503b7417ffdbdb0 ]--- [ 620.790065] RIP: 0010:assfail+0x20/0x28 [ 620.790642] Code: 31 ff e8 83 fc ff ff 0f 0b c3 48 89 f1 41 89 d0 48 c7 c6 48 ca 8d 82 48 89 fa 38 [ 620.793038] RSP: 0018:ffffc9000898bc10 EFLAGS: 00010202 [ 620.793609] RAX: 0000000000000000 RBX: ffff88012f14ba40 RCX: 0000000000000000 [ 620.794317] RDX: 00000000ffffffc0 RSI: 000000000000000a RDI: ffffffff828560d9 [ 620.795025] RBP: ffff88012f14b300 R08: 0000000000000000 R09: 0000000000000000 [ 620.795778] R10: 000000000000000a R11: f000000000000000 R12: ffffc9000898bc98 [ 620.796675] R13: ffffc9000898bc9c R14: ffff880130b5e2b8 R15: ffff88012a1fa2a8 [ 620.797782] FS: 00007fdc36e0fbc0(0000) GS:ffff88013ba00000(0000) knlGS:0000000000000000 [ 620.798908] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 620.799594] CR2: 00007fdc3604d000 CR3: 0000000132afc000 CR4: 00000000000006f0 [ 620.800424] Kernel panic - not syncing: Fatal exception [ 620.801191] Kernel Offset: disabled [ 620.801597] ---[ end Kernel panic - not syncing: Fatal exception ]--- Signed-off-by: NChristoph Hellwig <hch@lst.de> Reviewed-by: NDave Chinner <dchinner@redhat.com> Signed-off-by: NDave Chinner <david@fromorbit.com> Signed-off-by: NLuis Chamberlain <mcgrof@kernel.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Carlos Maiolino 提交于
commit 41657e5507b13e963be906d5d874f4f02374fd5c upstream. The addition of FIBT, RMAP and REFCOUNT changed the offsets into __xfssats structure. This caused xqmstat_proc_show() to display garbage data via /proc/fs/xfs/xqmstat, once it relies on the offsets marked via macros. Fix it. Fixes: 00f4e4f9 xfs: add rmap btree stats infrastructure Fixes: aafc3c24 xfs: support the XFS_BTNUM_FINOBT free inode btree type Fixes: 46eeb521 xfs: introduce refcount btree definitions Signed-off-by: NCarlos Maiolino <cmaiolino@redhat.com> Reviewed-by: NEric Sandeen <sandeen@redhat.com> Signed-off-by: NDave Chinner <david@fromorbit.com> Signed-off-by: NLuis Chamberlain <mcgrof@kernel.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Du Changbin 提交于
[ Upstream commit b058809bfc8faeb7b7cae047666e23375a060059 ] A bug is present in GDB which causes early string termination when parsing variables. This has been reported [0], but we should ensure that we can support at least basic printing of the core kernel strings. For current gdb version (has been tested with 7.3 and 8.1), 'lx-version' only prints one character. (gdb) lx-version L(gdb) This can be fixed by casting 'linux_banner' as (char *). (gdb) lx-version Linux version 4.19.0-rc1+ (changbin@acer) (gcc version 7.3.0 (Ubuntu 7.3.0-16ubuntu3)) #21 SMP Sat Sep 1 21:43:30 CST 2018 [0] https://sourceware.org/bugzilla/show_bug.cgi?id=20077 [kbingham@kernel.org: add detail to commit message] Link: http://lkml.kernel.org/r/20181111162035.8356-1-kieran.bingham@ideasonboard.com Fixes: 2d061d99 ("scripts/gdb: add version command") Signed-off-by: NDu Changbin <changbin.du@gmail.com> Signed-off-by: NKieran Bingham <kbingham@kernel.org> Acked-by: NJan Kiszka <jan.kiszka@siemens.com> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Anders Roxell 提交于
[ Upstream commit 634724431607f6f46c495dfef801a1c8b44a96d9 ] Since __sanitizer_cov_trace_const_cmp4 is marked as notrace, the function called from __sanitizer_cov_trace_const_cmp4 shouldn't be traceable either. ftrace_graph_caller() gets called every time func write_comp_data() gets called if it isn't marked 'notrace'. This is the backtrace from gdb: #0 ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:179 #1 0xffffff8010201920 in ftrace_caller () at ../arch/arm64/kernel/entry-ftrace.S:151 #2 0xffffff8010439714 in write_comp_data (type=5, arg1=0, arg2=0, ip=18446743524224276596) at ../kernel/kcov.c:116 #3 0xffffff8010439894 in __sanitizer_cov_trace_const_cmp4 (arg1=<optimized out>, arg2=<optimized out>) at ../kernel/kcov.c:188 #4 0xffffff8010201874 in prepare_ftrace_return (self_addr=18446743524226602768, parent=0xffffff801014b918, frame_pointer=18446743524223531344) at ./include/generated/atomic-instrumented.h:27 #5 0xffffff801020194c in ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:182 Rework so that write_comp_data() that are called from __sanitizer_cov_trace_*_cmp*() are marked as 'notrace'. Commit 903e8ff86753 ("kernel/kcov.c: mark funcs in __sanitizer_cov_trace_pc() as notrace") missed to mark write_comp_data() as 'notrace'. When that patch was created gcc-7 was used. In lib/Kconfig.debug config KCOV_ENABLE_COMPARISONS depends on $(cc-option,-fsanitize-coverage=trace-cmp) That code path isn't hit with gcc-7. However, it were that with gcc-8. Link: http://lkml.kernel.org/r/20181206143011.23719-1-anders.roxell@linaro.orgSigned-off-by: NAnders Roxell <anders.roxell@linaro.org> Signed-off-by: NArnd Bergmann <arnd@arndb.de> Co-developed-by: NArnd Bergmann <arnd@arndb.de> Acked-by: NSteven Rostedt (VMware) <rostedt@goodmis.org> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Oleg Nesterov 提交于
[ Upstream commit 8099b047ecc431518b9bb6bdbba3549bbecdc343 ] load_script() simply truncates bprm->buf and this is very wrong if the length of shebang string exceeds BINPRM_BUF_SIZE-2. This can silently truncate i_arg or (worse) we can execute the wrong binary if buf[2:126] happens to be the valid executable path. Change load_script() to return ENOEXEC if it can't find '\n' or zero in bprm->buf. Note that '\0' can come from either prepare_binprm()->memset() or from kernel_read(), we do not care. Link: http://lkml.kernel.org/r/20181112160931.GA28463@redhat.comSigned-off-by: NOleg Nesterov <oleg@redhat.com> Acked-by: NKees Cook <keescook@chromium.org> Acked-by: NMichal Hocko <mhocko@suse.com> Cc: Ben Woodard <woodard@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Davidlohr Bueso 提交于
[ Upstream commit 76699a67f3041ff4c7af6d6ee9be2bfbf1ffb671 ] The ep->ovflist is a secondary ready-list to temporarily store events that might occur when doing sproc without holding the ep->wq.lock. This accounts for every time we check for ready events and also send events back to userspace; both callbacks, particularly the latter because of copy_to_user, can account for a non-trivial time. As such, the unlikely() check to see if the pointer is being used, seems both misleading and sub-optimal. In fact, we go to an awful lot of trouble to sync both lists, and populating the ovflist is far from an uncommon scenario. For example, profiling a concurrent epoll_wait(2) benchmark, with CONFIG_PROFILE_ANNOTATED_BRANCHES shows that for a two threads a 33% incorrect rate was seen; and when incrementally increasing the number of epoll instances (which is used, for example for multiple queuing load balancing models), up to a 90% incorrect rate was seen. Similarly, by deleting the prediction, 3% throughput boost was seen across incremental threads. Link: http://lkml.kernel.org/r/20181108051006.18751-4-dave@stgolabs.netSigned-off-by: NDavidlohr Bueso <dbueso@suse.de> Reviewed-by: NAndrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Jason Baron <jbaron@akamai.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Liu, Chuansheng 提交于
[ Upstream commit 168e06f7937d96c7222037d8a05565e8a6eb00fe ] Based on commit 401c636a ("kernel/hung_task.c: show all hung tasks before panic"), we could get the call stack of hung task. However, if the console loglevel is not high, we still can not see the useful panic information in practice, and in most cases users don't set console loglevel to high level. This patch is to force console verbose before system panic, so that the real useful information can be seen in the console, instead of being like the following, which doesn't have hung task information. INFO: task init:1 blocked for more than 120 seconds. Tainted: G U W 4.19.0-quilt-2e5dc0ac-g51b6c21d76cc #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Kernel panic - not syncing: hung_task: blocked tasks CPU: 2 PID: 479 Comm: khungtaskd Tainted: G U W 4.19.0-quilt-2e5dc0ac-g51b6c21d76cc #1 Call Trace: dump_stack+0x4f/0x65 panic+0xde/0x231 watchdog+0x290/0x410 kthread+0x12c/0x150 ret_from_fork+0x35/0x40 reboot: panic mode set: p,w Kernel Offset: 0x34000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff) Link: http://lkml.kernel.org/r/27240C0AC20F114CBF8149A2696CBE4A6015B675@SHSMSX101.ccr.corp.intel.comSigned-off-by: NChuansheng Liu <chuansheng.liu@intel.com> Reviewed-by: NPetr Mladek <pmladek@suse.com> Reviewed-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Cheng Lin 提交于
[ Upstream commit 09be178400829dddc1189b50a7888495dd26aa84 ] If the number of input parameters is less than the total parameters, an EINVAL error will be returned. For example, we use proc_doulongvec_minmax to pass up to two parameters with kern_table: { .procname = "monitor_signals", .data = &monitor_sigs, .maxlen = 2*sizeof(unsigned long), .mode = 0644, .proc_handler = proc_doulongvec_minmax, }, Reproduce: When passing two parameters, it's work normal. But passing only one parameter, an error "Invalid argument"(EINVAL) is returned. [root@cl150 ~]# echo 1 2 > /proc/sys/kernel/monitor_signals [root@cl150 ~]# cat /proc/sys/kernel/monitor_signals 1 2 [root@cl150 ~]# echo 3 > /proc/sys/kernel/monitor_signals -bash: echo: write error: Invalid argument [root@cl150 ~]# echo $? 1 [root@cl150 ~]# cat /proc/sys/kernel/monitor_signals 3 2 [root@cl150 ~]# The following is the result after apply this patch. No error is returned when the number of input parameters is less than the total parameters. [root@cl150 ~]# echo 1 2 > /proc/sys/kernel/monitor_signals [root@cl150 ~]# cat /proc/sys/kernel/monitor_signals 1 2 [root@cl150 ~]# echo 3 > /proc/sys/kernel/monitor_signals [root@cl150 ~]# echo $? 0 [root@cl150 ~]# cat /proc/sys/kernel/monitor_signals 3 2 [root@cl150 ~]# There are three processing functions dealing with digital parameters, __do_proc_dointvec/__do_proc_douintvec/__do_proc_doulongvec_minmax. This patch deals with __do_proc_doulongvec_minmax, just as __do_proc_dointvec does, adding a check for parameters 'left'. In __do_proc_douintvec, its code implementation explicitly does not support multiple inputs. static int __do_proc_douintvec(...){ ... /* * Arrays are not supported, keep this simple. *Do not* add * support for them. */ if (vleft != 1) { *lenp = 0; return -EINVAL; } ... } So, just __do_proc_doulongvec_minmax has the problem. And most use of proc_doulongvec_minmax/proc_doulongvec_ms_jiffies_minmax just have one parameter. Link: http://lkml.kernel.org/r/1544081775-15720-1-git-send-email-cheng.lin130@zte.com.cnSigned-off-by: NCheng Lin <cheng.lin130@zte.com.cn> Acked-by: NLuis Chamberlain <mcgrof@kernel.org> Reviewed-by: NKees Cook <keescook@chromium.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Tetsuo Handa 提交于
[ Upstream commit 304ae42739b108305f8d7b3eb3c1aec7c2b643a9 ] check_hung_uninterruptible_tasks() is currently calling rcu_lock_break() for every 1024 threads. But check_hung_task() is very slow if printk() was called, and is very fast otherwise. If many threads within some 1024 threads called printk(), the RCU grace period might be extended enough to trigger RCU stall warnings. Therefore, calling rcu_lock_break() for every some fixed jiffies will be safer. Link: http://lkml.kernel.org/r/1544800658-11423-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jpSigned-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Acked-by: NPaul E. McKenney <paulmck@linux.ibm.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Dave Martin 提交于
[ Upstream commit ee1b465b303591d3a04d403122bbc0d7026520fb ] SVE_PT_REGS_OFFSET is supposed to indicate the offset for skipping over the ptrace NT_ARM_SVE header (struct user_sve_header) to the start of the SVE register data proper. However, currently SVE_PT_REGS_OFFSET is defined in terms of struct sve_context, which is wrong: that structure describes the SVE header in the signal frame, not in the ptrace regset. This patch fixes the definition to use the ptrace header structure struct user_sve_header instead. By good fortune, the two structures are the same size anyway, so there is no functional or ABI change. Signed-off-by: NDave Martin <Dave.Martin@arm.com> Signed-off-by: NWill Deacon <will.deacon@arm.com> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Aditya Pakki 提交于
[ Upstream commit 6ae16dfb61bce538d48b7fe98160fada446056c5 ] In lenovo_probe_tpkbd(), the function of_led_classdev_register() could return an error value that is unchecked. The fix adds these checks. Signed-off-by: NAditya Pakki <pakki001@umn.edu> Signed-off-by: NJiri Kosina <jkosina@suse.cz> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Bjorn Andersson 提交于
[ Upstream commit 9d216211fded20fff301d0317af3238d8383634c ] First correct the edge case to return the last element if we're outside the range, rather than at the last element, so that interpolation is not omitted for points between the two last entries in the table. Then correct the formula to perform linear interpolation based the two points surrounding the read ADC value. The indices for temp are kept as "hi" and "lo" to pair with the adc indices, but there's no requirement that the temperature is provided in descendent order. mult_frac() is used to prevent issues with overflowing the int. Cc: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: NEduardo Valentin <edubezval@gmail.com> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Richard Zhu 提交于
[ Upstream commit 75cb8d20c112aba70f23d98e3f8d0a38ace16006 ] The MSI Enable bit in the MSI Capability (PCIe r4.0, sec 7.7.1.2) controls whether a Function can request service using MSI. i.MX6 Root Ports implement the MSI Capability and may use MSI to request service for events like PME, hotplug, AER, etc. In addition, on i.MX6, the MSI Enable bit controls delivery of MSI interrupts from components below the Root Port. Prior to f3fdfc4a ("PCI: Remove host driver Kconfig selection of CONFIG_PCIEPORTBUS"), enabling CONFIG_PCI_IMX6 automatically also enabled CONFIG_PCIEPORTBUS, and when portdrv claimed the Root Ports, it set the MSI Enable bit so it could use PME, hotplug, AER, etc. As a side effect, that also enabled delivery of MSI interrupts from downstream components. The imx6q-pcie driver itself does not depend on portdrv, so set MSI Enable in imx6q-pcie so MSI from downstream components works even if nobody uses MSI for the Root Port events. Fixes: f3fdfc4a ("PCI: Remove host driver Kconfig selection of CONFIG_PCIEPORTBUS") Signed-off-by: NRichard Zhu <hongxing.zhu@nxp.com> Signed-off-by: NBjorn Helgaas <bhelgaas@google.com> Tested-by: NSven Van Asbroeck <TheSven73@googlemail.com> Tested-by: NTrent Piepho <tpiepho@impinj.com> Reviewed-by: NLucas Stach <l.stach@pengutronix.de> Acked-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Douglas Anderson 提交于
[ Upstream commit 162bc7f5afd75b72acbe3c5f3488ef7e64a3fe36 ] If you have a CPU that fails to round up and then run 'btc' you'll end up crashing in kdb becaue we dereferenced NULL. Let's add a check. It's wise to also set the task to NULL when leaving the debugger so that if we fail to round up on a later entry into the debugger we won't backtrace a stale task. Signed-off-by: NDouglas Anderson <dianders@chromium.org> Acked-by: NDaniel Thompson <daniel.thompson@linaro.org> Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Matthias Brugger 提交于
[ Upstream commit d56c19d07e0bc3ceff366a49b7d7a2440c967b1b ] By defaul of-based thermal driver do not enable hwmon. This patch does this explicitly, so that the temperature can be read through the common hwmon sysfs. Signed-off-by: NMatthias Brugger <mbrugger@suse.com> Acked-by: NStefan Wahren <stefan.wahren@i2se.com> Signed-off-by: NEduardo Valentin <edubezval@gmail.com> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Finn Thain 提交于
[ Upstream commit 296dcc40f2f2e402facf7cd26cf3f2c8f4b17d47 ] When the block device is opened with FMODE_EXCL, ref_count is set to -1. This value doesn't get reset when the device is closed which means the device cannot be opened again. Fix this by checking for refcount <= 0 in the release method. Reported-and-tested-by: NStan Johnson <userm57@yahoo.com> Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: NFinn Thain <fthain@telegraphics.com.au> Signed-off-by: NJens Axboe <axboe@kernel.dk> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Scott Wood 提交于
[ Upstream commit 0d9c9a238faf925823bde866182c663b6d734f2e ] These functions are called from atomic context: [ 9.150239] BUG: sleeping function called from invalid context at /home/scott/git/linux/mm/slab.h:421 [ 9.158159] in_atomic(): 1, irqs_disabled(): 0, pid: 4432, name: ip [ 9.163128] CPU: 8 PID: 4432 Comm: ip Not tainted 4.20.0-rc2-00169-g63d86876f324 #29 [ 9.163130] Call Trace: [ 9.170701] [c0000002e899a980] [c0000000009c1068] .dump_stack+0xa8/0xec (unreliable) [ 9.177140] [c0000002e899aa10] [c00000000007a7b4] .___might_sleep+0x138/0x164 [ 9.184440] [c0000002e899aa80] [c0000000001d5bac] .kmem_cache_alloc_trace+0x238/0x30c [ 9.191216] [c0000002e899ab40] [c00000000065ea1c] .memac_add_hash_mac_address+0x104/0x198 [ 9.199464] [c0000002e899abd0] [c00000000065a788] .set_multi+0x1c8/0x218 [ 9.206242] [c0000002e899ac80] [c0000000006615ec] .dpaa_set_rx_mode+0xdc/0x17c [ 9.213544] [c0000002e899ad00] [c00000000083d2b0] .__dev_set_rx_mode+0x80/0xd4 [ 9.219535] [c0000002e899ad90] [c00000000083d334] .dev_set_rx_mode+0x30/0x54 [ 9.225271] [c0000002e899ae10] [c00000000083d4a0] .__dev_open+0x148/0x1c8 [ 9.230751] [c0000002e899aeb0] [c00000000083d934] .__dev_change_flags+0x19c/0x1e0 [ 9.230755] [c0000002e899af60] [c00000000083d9a4] .dev_change_flags+0x2c/0x80 [ 9.242752] [c0000002e899aff0] [c0000000008554ec] .do_setlink+0x350/0xf08 [ 9.248228] [c0000002e899b170] [c000000000857ad0] .rtnl_newlink+0x588/0x7e0 [ 9.253965] [c0000002e899b740] [c000000000852424] .rtnetlink_rcv_msg+0x3e0/0x498 [ 9.261440] [c0000002e899b820] [c000000000884790] .netlink_rcv_skb+0x134/0x14c [ 9.267607] [c0000002e899b8e0] [c000000000851840] .rtnetlink_rcv+0x18/0x2c [ 9.274558] [c0000002e899b950] [c000000000883c8c] .netlink_unicast+0x214/0x318 [ 9.281163] [c0000002e899ba00] [c000000000884220] .netlink_sendmsg+0x348/0x444 [ 9.287076] [c0000002e899bae0] [c00000000080d13c] .sock_sendmsg+0x2c/0x54 [ 9.287080] [c0000002e899bb50] [c0000000008106c0] .___sys_sendmsg+0x2d0/0x2d8 [ 9.298375] [c0000002e899bd30] [c000000000811a80] .__sys_sendmsg+0x5c/0xb0 [ 9.303939] [c0000002e899be20] [c0000000000006b0] system_call+0x60/0x6c Signed-off-by: NScott Wood <oss@buserror.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Wenwen Wang 提交于
[ Upstream commit 093c48213ee37c3c3ff1cf5ac1aa2a9d8bc66017 ] In probe_gdrom(), the buffer pointed by 'gd.cd_info' is allocated through kzalloc() and is used to hold the information of the gdrom device. To register and unregister the device, the pointer 'gd.cd_info' is passed to the functions register_cdrom() and unregister_cdrom(), respectively. However, this buffer is not freed after it is used, which can cause a memory leak bug. This patch simply frees the buffer 'gd.cd_info' in exit_gdrom() to fix the above issue. Signed-off-by: NWenwen Wang <wang6495@umn.edu> Signed-off-by: NJens Axboe <axboe@kernel.dk> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Jia-Ju Bai 提交于
[ Upstream commit 7418e6520f22a2e35815122fa5a53d5bbfa2c10f ] In drivers/isdn/hisax/hfc_pci.c, the functions hfcpci_interrupt() and HFCPCI_l1hw() may be concurrently executed. HFCPCI_l1hw() line 1173: if (!cs->tx_skb) hfcpci_interrupt() line 942: spin_lock_irqsave(); line 1066: dev_kfree_skb_irq(cs->tx_skb); Thus, a possible concurrency use-after-free bug may occur in HFCPCI_l1hw(). To fix these bugs, the calls to spin_lock_irqsave() and spin_unlock_irqrestore() are added in HFCPCI_l1hw(), to protect the access to cs->tx_skb. Signed-off-by: NJia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Minchan Kim 提交于
[ Upstream commit 3c9959e025472122a61faebb208525cf26b305d1 ] Patch series "zram idle page writeback", v3. Inherently, swap device has many idle pages which are rare touched since it was allocated. It is never problem if we use storage device as swap. However, it's just waste for zram-swap. This patchset supports zram idle page writeback feature. * Admin can define what is idle page "no access since X time ago" * Admin can define when zram should writeback them * Admin can define when zram should stop writeback to prevent wearout Details are in each patch's description. This patch (of 7): ================================ WARNING: inconsistent lock state 4.19.0+ #390 Not tainted -------------------------------- inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. zram_verify/2095 [HC0[0]:SC1[1]:HE1:SE0] takes: 00000000b1828693 (&(&zram->bitmap_lock)->rlock){+.?.}, at: put_entry_bdev+0x1e/0x50 {SOFTIRQ-ON-W} state was registered at: _raw_spin_lock+0x2c/0x40 zram_make_request+0x755/0xdc9 generic_make_request+0x373/0x6a0 submit_bio+0x6c/0x140 __swap_writepage+0x3a8/0x480 shrink_page_list+0x1102/0x1a60 shrink_inactive_list+0x21b/0x3f0 shrink_node_memcg.constprop.99+0x4f8/0x7e0 shrink_node+0x7d/0x2f0 do_try_to_free_pages+0xe0/0x300 try_to_free_pages+0x116/0x2b0 __alloc_pages_slowpath+0x3f4/0xf80 __alloc_pages_nodemask+0x2a2/0x2f0 __handle_mm_fault+0x42e/0xb50 handle_mm_fault+0x55/0xb0 __do_page_fault+0x235/0x4b0 page_fault+0x1e/0x30 irq event stamp: 228412 hardirqs last enabled at (228412): [<ffffffff98245846>] __slab_free+0x3e6/0x600 hardirqs last disabled at (228411): [<ffffffff98245625>] __slab_free+0x1c5/0x600 softirqs last enabled at (228396): [<ffffffff98e0031e>] __do_softirq+0x31e/0x427 softirqs last disabled at (228403): [<ffffffff98072051>] irq_exit+0xd1/0xe0 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&(&zram->bitmap_lock)->rlock); <Interrupt> lock(&(&zram->bitmap_lock)->rlock); *** DEADLOCK *** no locks held by zram_verify/2095. stack backtrace: CPU: 5 PID: 2095 Comm: zram_verify Not tainted 4.19.0+ #390 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014 Call Trace: <IRQ> dump_stack+0x67/0x9b print_usage_bug+0x1bd/0x1d3 mark_lock+0x4aa/0x540 __lock_acquire+0x51d/0x1300 lock_acquire+0x90/0x180 _raw_spin_lock+0x2c/0x40 put_entry_bdev+0x1e/0x50 zram_free_page+0xf6/0x110 zram_slot_free_notify+0x42/0xa0 end_swap_bio_read+0x5b/0x170 blk_update_request+0x8f/0x340 scsi_end_request+0x2c/0x1e0 scsi_io_completion+0x98/0x650 blk_done_softirq+0x9e/0xd0 __do_softirq+0xcc/0x427 irq_exit+0xd1/0xe0 do_IRQ+0x93/0x120 common_interrupt+0xf/0xf </IRQ> With writeback feature, zram_slot_free_notify could be called in softirq context by end_swap_bio_read. However, bitmap_lock is not aware of that so lockdep yell out: get_entry_bdev spin_lock(bitmap->lock); irq softirq end_swap_bio_read zram_slot_free_notify zram_slot_lock <-- deadlock prone zram_free_page put_entry_bdev spin_lock(bitmap->lock); <-- deadlock prone With akpm's suggestion (i.e. bitmap operation is already atomic), we could remove bitmap lock. It might fail to find a empty slot if serious contention happens. However, it's not severe problem because huge page writeback has already possiblity to fail if there is severe memory pressure. Worst case is just keeping the incompressible in memory, not storage. The other problem is zram_slot_lock in zram_slot_slot_free_notify. To make it safe is this patch introduces zram_slot_trylock where zram_slot_free_notify uses it. Although it's rare to be contented, this patch adds new debug stat "miss_free" to keep monitoring how often it happens. Link: http://lkml.kernel.org/r/20181127055429.251614-2-minchan@kernel.orgSigned-off-by: NMinchan Kim <minchan@kernel.org> Reviewed-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com> Reviewed-by: NJoey Pabalinas <joeypabalinas@gmail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Waiman Long 提交于
[ Upstream commit 3c0c12cc8f00ca5f81acb010023b8eb13e9a7004 ] When CONFIG_KASAN is enabled on large memory SMP systems, the deferrred pages initialization can take a long time. Below were the reported init times on a 8-socket 96-core 4TB IvyBridge system. 1) Non-debug kernel without CONFIG_KASAN [ 8.764222] node 1 initialised, 132086516 pages in 7027ms 2) Debug kernel with CONFIG_KASAN [ 146.288115] node 1 initialised, 132075466 pages in 143052ms So the page init time in a debug kernel was 20X of the non-debug kernel. The long init time can be problematic as the page initialization is done with interrupt disabled. In this particular case, it caused the appearance of following warning messages as well as NMI backtraces of all the cores that were doing the initialization. [ 68.240049] rcu: INFO: rcu_sched detected stalls on CPUs/tasks: [ 68.241000] rcu: 25-...0: (100 ticks this GP) idle=b72/1/0x4000000000000000 softirq=915/915 fqs=16252 [ 68.241000] rcu: 44-...0: (95 ticks this GP) idle=49a/1/0x4000000000000000 softirq=788/788 fqs=16253 [ 68.241000] rcu: 54-...0: (104 ticks this GP) idle=03a/1/0x4000000000000000 softirq=721/825 fqs=16253 [ 68.241000] rcu: 60-...0: (103 ticks this GP) idle=cbe/1/0x4000000000000000 softirq=637/740 fqs=16253 [ 68.241000] rcu: 72-...0: (105 ticks this GP) idle=786/1/0x4000000000000000 softirq=536/641 fqs=16253 [ 68.241000] rcu: 84-...0: (99 ticks this GP) idle=292/1/0x4000000000000000 softirq=537/537 fqs=16253 [ 68.241000] rcu: 111-...0: (104 ticks this GP) idle=bde/1/0x4000000000000000 softirq=474/476 fqs=16253 [ 68.241000] rcu: (detected by 13, t=65018 jiffies, g=249, q=2) The long init time was mainly caused by the call to kasan_free_pages() to poison the newly initialized pages. On a 4TB system, we are talking about almost 500GB of memory probably on the same node. In reality, we may not need to poison the newly initialized pages before they are ever allocated. So KASAN poisoning of freed pages before the completion of deferred memory initialization is now disabled. Those pages will be properly poisoned when they are allocated or freed after deferred pages initialization is done. With this change, the new page initialization time became: [ 21.948010] node 1 initialised, 132075466 pages in 18702ms This was still about double the non-debug kernel time, but was much better than before. Link: http://lkml.kernel.org/r/1544459388-8736-1-git-send-email-longman@redhat.comSigned-off-by: NWaiman Long <longman@redhat.com> Reviewed-by: NAndrew Morton <akpm@linux-foundation.org> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Pasha Tatashin <Pavel.Tatashin@microsoft.com> Cc: Oscar Salvador <osalvador@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Larry Chen 提交于
[ Upstream commit 9e6aea22802b5684c7e1d69822aeb0844dd01953 ] Included file path was hard-wired in the ocfs2 makefile, which might causes some confusion when compiling ocfs2 as an external module. Say if we compile ocfs2 module as following. cp -r /kernel/tree/fs/ocfs2 /other/dir/ocfs2 cd /other/dir/ocfs2 make -C /path/to/kernel_source M=`pwd` modules Acutally, the compiler wil try to find included file in /kernel/tree/fs/ocfs2, rather than the directory /other/dir/ocfs2. To fix this little bug, we introduce the var $(src) provided by kbuild. $(src) means the absolute path of the running kbuild file. Link: http://lkml.kernel.org/r/20181108085546.15149-1-lchen@suse.comSigned-off-by: NLarry Chen <lchen@suse.com> Reviewed-by: NAndrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Junxiao Bi 提交于
[ Upstream commit 70306d9dce75abde855cefaf32b3f71eed8602a3 ] For sync io read in ocfs2_read_blocks_sync(), first clear bh uptodate flag and submit the io, second wait io done, last check whether bh uptodate, if not return io error. If two sync io for the same bh were issued, it could be the first io done and set uptodate flag, but just before check that flag, the second io came in and cleared uptodate, then ocfs2_read_blocks_sync() for the first io will return IO error. Indeed it's not necessary to clear uptodate flag, as the io end handler end_buffer_read_sync() will set or clear it based on io succeed or failed. The following message was found from a nfs server but the underlying storage returned no error. [4106438.567376] (nfsd,7146,3):ocfs2_get_suballoc_slot_bit:2780 ERROR: read block 1238823695 failed -5 [4106438.567569] (nfsd,7146,3):ocfs2_get_suballoc_slot_bit:2812 ERROR: status = -5 [4106438.567611] (nfsd,7146,3):ocfs2_test_inode_bit:2894 ERROR: get alloc slot and bit failed -5 [4106438.567643] (nfsd,7146,3):ocfs2_test_inode_bit:2932 ERROR: status = -5 [4106438.567675] (nfsd,7146,3):ocfs2_get_dentry:94 ERROR: test inode bit failed -5 Same issue in non sync read ocfs2_read_blocks(), fixed it as well. Link: http://lkml.kernel.org/r/20181121020023.3034-4-junxiao.bi@oracle.comSigned-off-by: NJunxiao Bi <junxiao.bi@oracle.com> Reviewed-by: NChangwei Ge <ge.changwei@h3c.com> Reviewed-by: NYiwen Jiang <jiangyiwen@huawei.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Jun Piao <piaojun@huawei.com> Cc: Mark Fasheh <mfasheh@versity.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Randy Dunlap 提交于
[ Upstream commit 440e7b379f91acd245d5c8de94d533f40f5dffb3 ] arch/sh/boards/mach-kfr2r09/setup.c does not need to #include <mtd/onenand.h>, and doing so causes a build warning, so drop that header file. In file included from ../arch/sh/boards/mach-kfr2r09/setup.c:28: ../include/linux/mtd/onenand.h:225:12: warning: 'struct mtd_oob_ops' declared inside parameter list will not be visible outside of this definition or declaration struct mtd_oob_ops *ops); Link: http://lkml.kernel.org/r/702f0a25-c63e-6912-4640-6ab0f00afbc7@infradead.org Fixes: f3590dc3 ("media: arch: sh: kfr2r09: Use new renesas-ceu camera driver") Signed-off-by: NRandy Dunlap <rdunlap@infradead.org> Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org> Suggested-by: NMiquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: NMiquel Raynal <miquel.raynal@bootlin.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Rich Felker <dalias@libc.org> Cc: Jacopo Mondi <jacopo+renesas@jmondi.org> Cc: Magnus Damm <magnus.damm@gmail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-
由 Marc Zyngier 提交于
[ Upstream commit 67a28de47faa83585dd644bd4c31e5a1d9346c50 ] Running something like: decodecode vmlinux . leads to interested results where not only the leading "." gets stripped from the displayed paths, but also anywhere in the string, displaying something like: kvm_vcpu_check_block (arch/arm64/kvm/virt/kvm/kvm_mainc:2141) which doesn't help further processing. Fix it by only stripping the base path if it is a prefix of the path. Link: http://lkml.kernel.org/r/20181210174659.31054-3-marc.zyngier@arm.comSigned-off-by: NMarc Zyngier <marc.zyngier@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org> Signed-off-by: NSasha Levin <sashal@kernel.org>
-