Mirror the changes made to ixgbe in commit 2367a173
("ixgbe: flush when in xmit_more mode and under descriptor pressure")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mirror the changes made to ixgbe in commit 2367a173
("ixgbe: flush when in xmit_more mode and under descriptor pressure")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When xmit_more mode is being used and the ring is about to
become full or the stack has stopped the ring, enforce a tail
pointer write to the hw. Otherwise, we could risk a TX hang.

Code suggested by Alexander Duyck.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add two new entries to the Broadcom BCM7xxx internal PHY driver for
BCM7250 and BCM7364 chips. Those chips share the usual 28nm process
Gigabit PHY sequence and require the same workarounds so far.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All 28nm Gigabit PHYs supported by the driver have the same
callbacks, the only differences being the 32-bits OUI and the name. Use
a macro to factor this, making it easier in the future to add new
entries.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sungem driver has "phy_read()" and "phy_write()" functions, which
we need to rename because the generic phy layer is about to export
generic interfaces with the same name.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the Broadcom Starfigther 2 switch chip using a DSA
driver. This switch driver supports the following features:

- configuration of the external switch port interface: MII, RevMII,
  RGMII and RGMII_NO_ID are supported
- support for the per-port MIB counters
- support for link interrupts for special ports (e.g: MoCA)
- powering up/down of switch memories to conserve power when ports are
  unused

Finally, update the compatible property for the DSA core code to match
our switch top-level compatible node.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a generic UniMAC MDIO bus driver and its Device Tree binding, which
can be used by the BCMGENET driver as-is, and the upcoming Starfighter 2
Ethernet switch MDIO bus controller.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sungem driver has "phy_read()" and "phy_write()" functions, which
we need to rename because the generic phy layer is about to export
generic interfaces with the same name.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dmfe driver has "phy_read()" and "phy_write()" functions, which
we need to rename because the generic phy layer is about to export
generic interfaces with the same name.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some platforms have special bank registers which might be used to
select the correct clock or the right mode for Media Indepent Interface
controllers. Sometimes, it is also required to activate vcc regulators
in the right order to supply the ethernet controller at the right time.
This patch is an architecture refactoring of the arc-emac device driver.
It adds a new software design which allows to add specific platform
glue layer. Each platform has now its own module which performs custom
initialization and remove for the target and then calls to the
core driver.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is an api changes for the emac_mdio.c module.
It will be required later when arc_emac_probe/arc_emac_remove
will no longer use 'struct platform_device'.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a preparation of an api changes for the emac_main.c module.
The involved functions are arc_emac_probe and arc_emac_remove.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Incorrect checking of array instead of array contents in panic_dump
flow - results of commit e2611998 ("bnx2x: Safe bnx2x_panic_dump()").
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the strncpy with strlcpy, and use sizeof to determine the
length.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x uses ptp functions, so it should select the provider of
those functions (PTP_1588_CLOCK).  Fixes these build errors:

drivers/built-in.o: In function `__bnx2x_remove':
/home/jim/linux/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:13409:
undefined reference to `ptp_clock_unregister'
drivers/built-in.o: In function `bnx2x_register_phc':
/home/jim/linux/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:13202:
undefined reference to `ptp_clock_register'
drivers/built-in.o: In function `bnx2x_get_ts_info':
/home/jim/linux/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3498:
undefined reference to `ptp_clock_index'
Reported-by: NJim Davis <jim.epost@gmail.com>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When one tries to add eth as a port into team and that eth is already in
use by other rx_handler device (macvlan, bond, bridge, ...) a bug in
team_port_add() causes that IFF_TEAM_PORT flag is set before rx_handler
is registered. In between, netdev nofifier is called and
team_device_event() sees IFF_TEAM_PORT and thinks that rx_handler_data
pointer is set to team_port. But it isn't.

Fix this by reordering rx_handler register and IFF_TEAM_PORT priv flag
set so it is very similar to how bonding does this.
Reported-by: NErik Hugne <erik.hugne@ericsson.com>
Fixes: 3d249d4c "net: introduce ethernet teaming device"
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit eeed018c ("bnx2x: Add timestamping and PTP hardware clock support")
has a missing conversion to LE32, which will prevent the feature from working
on big endian machines.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This introduces 2 new relaxations in the bnx2x driver regarding GRO:
  1. Don't prevent SW GRO if HW GRO is disabled.
  2. If all aggregations are disabled, when GRO configuration changes
     there's no need to perform an inner-reload [since it will have no
     actual effect].
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During statistics initialization of a VF we need to clean its statistics.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When STOP_ON_ERROR is set driver will not compile. Even if it did,
traffic will not pass without this patch as several fields which are
verified by FW/HW on the Tx path are not properly set.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This changes slightly the set of registers read during `ethtool -d'.
Without this change, it's possible the HW will generate a grc Attention which
will be logged into system logs as `grc timeout'.
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This implements the deferred tail pointer flush API for the ixgbe
driver. Similar version also proposed longer time ago by Alexander Duyck.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Jesper Dangaard Brouer, for high packet rates the
overhead of having another indirect call in the TX path is
non-trivial.

There is the indirect call itself, and then there is all of the
reloading of the state to refetch the tail pointer value and
then write the device register.

Move to a more passive scheme, which requires very light modifications
to the device drivers.

The signal is a new skb->xmit_more value, if it is non-zero it means
that more SKBs are pending to be transmitted on the same queue as the
current SKB.  And therefore, the driver may elide the tail pointer
update.

Right now skb->xmit_more is always zero.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use is_kdump_kernel() to detect kdump kernel, instead of
reset_devices.

CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds simple cleanups for stmmac, removing test we know is always
true, fixing whitespace, and moving code out of if().
Signed-off-by: NPavel Machek <pavel@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

626: CHECK: Alignment should match open parenthesis
 646: CHECK: Alignment should match open parenthesis
 655: CHECK: Alignment should match open parenthesis
 695: CHECK: Alignment should match open parenthesis
 729: CHECK: Alignment should match open parenthesis
 739: CHECK: Alignment should match open parenthesis
 976: WARNING: externs should be avoided in .c files
 1314: CHECK: Alignment should match open parenthesis
 1358: WARNING: networking block comments don't use an empty /* line, use /* Comment...
 1402: WARNING: networking block comments don't use an empty /* line, use /* Comment...
 1521: CHECK: multiple assignments should be avoided
 1775: CHECK: Alignment should match open parenthesis
 1838: CHECK: multiple assignments should be avoided
 1843: CHECK: multiple assignments should be avoided
 1847: CHECK: multiple assignments should be avoided
 1850: WARNING: Missing a blank line after declarations
 1864: CHECK: Alignment should match open parenthesis
 1872: CHECK: braces {} should be used on all arms of this statement
 1906: CHECK: usleep_range is preferred over udelay
 2865: WARNING: networking block comments don't use an empty /* line, use /* Comment...
 3088: CHECK: Alignment should match open parenthesis
 total: 0 errors, 5 warnings, 16 checks, 3567 lines checked
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This cuts down the number of debug information spit out by
the driver.
Signed-off-by: NDariusz Marcinkiewicz <reksio@newterm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 28nm Gigabit PHY on BCM7xxx chips comes out of reset with absolutely
no EEE capabilities, such that we would actually return that we do not
support EEE when accessing 3.20 (MDIO_PCS_EEE_ABLE) registers.

Poke through the vendor-specific C45 register to enable EEE globally at
the PHY level, and advertise supported EEE modes.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Internal PHYs do not have any specific phy_interface_t defined because
they are within an Ethernet MAC or a larger IC, they will fail the early
check in phy_init_eee(). Allow these PHYs to proceed with EEE
initialization and report error/success by checking the standard C45
EEE-related registers.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some PHY drivers might need to access Clause 45 registers in Clause 22
compatibility mode to e.g: properly advertise EEE support when disabled
by default.

Export these two helper functions: phy_read_mmd_indirect() and
phy_write_mmd_indirect() for drivers to use them.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fixed PHY driver does not properly emulate Clause 45 over Clause 22
MDIO reads, and as such, will return bogus values when we access such
registers.

Return an error when accessing these registers in order to prevent
advertising bogus capabilities such as EEE support and such.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 28nm process BCM7xxx internal Gigabit PHYs all support automatic
power down, turn on that feature as part of the configuration
initialization callback.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The shadow register 0x1C is used both by the BCM54xxx PHYs and the
BCM7xxx internal PHYs, move the accessors to a common location so both
drivers can use them.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 439d39a9 ("net: phy: broadcom:
extract register definitions") added a bunch of registers to brcmphy.h
but left some to broadcom.c, move all of them to the header file since
the BCM54xx and BCM7xxx PHY drivers do share all of these registers.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bare register numbers are used despite <uapi/linux/mdio.h> has MDIO_DEVS[12]
#define'd for those.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first initializer in the following

        union vxlan_addr ipa = {
            .sin.sin_addr.s_addr = tip,
            .sa.sa_family = AF_INET,
        };

is optimised away by the compiler, due to the second initializer,
therefore initialising .sin.sin_addr.s_addr always to 0.
This results in netlink messages indicating a L3 miss never contain the
missed IP address. This was observed with GCC 4.8 and 4.9. I do not know about previous versions.
The problem affects user space programs relying on an IP address being
sent as part of a netlink message indicating a L3 miss.

Changing
            .sa.sa_family = AF_INET,
to
            .sin.sin_family = AF_INET,
fixes the problem.
Signed-off-by: NGerhard Stenzel <gerhard.stenzel@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>