- 13 1月, 2016 1 次提交
-
-
由 Russell Currey 提交于
The recently added OPAL API call, OPAL_CONSOLE_FLUSH, originally took no parameters and returned nothing. The call was updated to accept the terminal number to flush, and returned various values depending on the state of the output buffer. The prototype has been updated and its usage in the OPAL kmsg dumper has been modified to support its new behaviour as an incremental flush. Signed-off-by: NRussell Currey <ruscur@russell.cc> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
- 12 1月, 2016 2 次提交
-
-
由 Hugh Dickins 提交于
Swapoff after swapping hangs on the G5, when CONFIG_CHECKPOINT_RESTORE=y but CONFIG_MEM_SOFT_DIRTY is not set. That's because the non-zero _PAGE_SWP_SOFT_DIRTY bit, added by CONFIG_HAVE_ARCH_SOFT_DIRTY=y, is not discounted when CONFIG_MEM_SOFT_DIRTY is not set: so swap ptes cannot be recognized. (I suspect that the peculiar dependence of HAVE_ARCH_SOFT_DIRTY on CHECKPOINT_RESTORE in arch/powerpc/Kconfig comes from an incomplete attempt to solve this problem.) It's true that the relationship between CONFIG_HAVE_ARCH_SOFT_DIRTY and and CONFIG_MEM_SOFT_DIRTY is too confusing, and it's true that swapoff should be made more robust; but nevertheless, fix up the powerpc ifdefs as x86_64 and s390 (which met the same problem) have them, defining the bits as 0 if CONFIG_MEM_SOFT_DIRTY is not set. Fixes: 7207f436 ("powerpc/mm: Add page soft dirty tracking") Signed-off-by: NHugh Dickins <hughd@google.com> Reviewed-by: NCyrill Gorcunov <gorcunov@openvz.org> Acked-by: NLaurent Dufour <ldufour@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Aneesh Kumar K.V 提交于
Core kernel expects swp_entry_t to consist of only swap type and swap offset. We should not leak pte bits into swp_entry_t. This breaks swapoff which use the swap type and offset to build a swp_entry_t and later compare that to the swp_entry_t obtained from linux page table pte. Leaking pte bits into swp_entry_t breaks that comparison and results in us looping in try_to_unuse. The stack trace can be anywhere below try_to_unuse() in mm/swapfile.c, since swapoff is circling around and around that function, reading from each used swap block into a page, then trying to find where that page belongs, looking at every non-file pte of every mm that ever swapped. Fixes: 6a119eae ("powerpc/mm: Add a _PAGE_PTE bit") Reported-by: NHugh Dickins <hughd@google.com> Suggested-by: NHugh Dickins <hughd@google.com> Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Acked-by: NHugh Dickins <hughd@google.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
- 11 1月, 2016 9 次提交
-
-
由 Uma Krishnan 提交于
Add support for future IBM Coherent Accelerator (CXL) device with ID of 0x0601. Signed-off-by: NUma Krishnan <ukrishn@linux.vnet.ibm.com> Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Brian Norris 提交于
Some developers really like to have -Werror enabled for their code, as it helps to ensure warning free code. Others don't want -Werror, as it (for example) can cause problems when newer (or older) compilers have different sets of warnings, or new warnings can appear just when turning up the warning level (e.g., make W=1 or W=2). Thus, it seems prudent to have the use of -Werror be configurable. It so happens that cxl is only built on PowerPC, and PowerPC already has a nice set of Kconfig options for this, under CONFIG_PPC_WERROR. So let's use that, and the world is a happy place again! (Note that PPC_WERROR defaults to =y, so the common case compile should still be enforcing -Werror.) Fixes: d3d73f4b ("cxl: Compile with -Werror") Signed-off-by: NBrian Norris <computersforpeace@gmail.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Brian Norris 提交于
GCC 4.6.3 does not support -Wno-unused-const-variable. Instead, use the kbuild infrastructure that checks if this options exists. Fixes: 2cd55c68 ("cxl: Fix build failure due to -Wunused-variable behaviour change") Suggested-by: NMichal Marek <mmarek@suse.com> Suggested-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NBrian Norris <computersforpeace@gmail.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Michael Ellerman 提交于
In order to support Power9 we need two new HWCAP bits. We are merging these ahead of the cputable entry so that glibc can start referring to them. Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Alistair Popple 提交于
P8+ hardware reports all errors on PE#0. This patch ensures PE#0 is not assigned to NPU devices so that it can be used for EEH. Signed-off-by: NAlistair Popple <alistair@popple.id.au> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Alistair Popple 提交于
The P8+ hardware supports four partitionable endpoints (PEs) however the hardware reports all errors as occurring on PE#0. This means we need to reserve this PE for error handling (EEH) and not assign it to a NPU device, implying that some devices will need to share PEs. This patch changes the PE assignment for NPU devices such that NPU devices which connect to the same GPU are assigned to the same PE#. Signed-off-by: NAlistair Popple <alistair@popple.id.au> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Alistair Popple 提交于
The emulated NVLink PCI devices share the same IODA2 TCE tables but only support a single TVT (instead of the normal two for PCI devices). This requires the kernel to manually replace windows with either the bypass or non-bypass window depending on what the driver has requested. Unfortunately an incorrect optimisation was made in pnv_pci_ioda_dma_set_mask() which caused updating of some NPU device PEs to be skipped in certain configurations due to an incorrect assumption that a NULL peer PE in the array indicated there were no more peers present. This patch fixes the problem by ensuring all peer PEs are updated. Fixes: 5d2aa710 ("powerpc/powernv: Add support for Nvlink NPUs") Signed-off-by: NAlistair Popple <alistair@popple.id.au> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Russell Currey 提交于
PCI in powernv now supports quite a bit more than p5ioc2, so remove the outdated comment. Signed-off-by: NRussell Currey <ruscur@russell.cc> Acked-by: NStewart Smith <stewart@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Steven Rostedt 提交于
It has come to my attention that kprobe event stack tracing does not work on powerpc. You can see with the following: # cd /sys/kernel/debug/tracing # echo stacktrace > trace_options # echo 'p kfree' > kprobe_events # echo 1 > events/kprobes/enable Will print the following warning: save_stack_trace_regs() not implemented yet. Although save_stack_trace() (which normal event stack traces use) is implemented, save_stack_trace_regs() which kprobe events use is not. This is a cheap attempt to implement that function. Note, This may have issues if a task tries to get a stack trace from another task with its regs, because it just passes in "current" to save_context_stack(). But this does solve the issue with stack tracing kprobe events. Reported-by: NChunyu Hu <chuhu@redhat.com> Signed-off-by: NSteven Rostedt <rostedt@goodmis.org> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
- 09 1月, 2016 1 次提交
-
-
由 Michael Ellerman 提交于
Commit 2fc251a8 ("powerpc: Copy only required pieces of the mm_context_t to the paca") broke the build for CONFIG_PPC_STD_MMU_64=y and CONFIG_PPC_MM_SLICES=n. That only happens for a kernel built with 4K pages and HUGETLB disabled, which is why we missed it. Fix it by adding a mm_ctx_user_psize member to the paca and populating it in the appropriate places. Fixes: 2fc251a8 ("powerpc: Copy only required pieces of the mm_context_t to the paca") Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
- 05 1月, 2016 1 次提交
-
-
由 Vaibhav Jain 提交于
Presently when a user-space process issues CXL_IOCTL_START_WORK ioctl we store the pid of the current task_struct and use it to get pointer to the mm_struct of the process, while processing page or segment faults from the capi card. However this causes issues when the thread that had originally issued the start-work ioctl exits in which case the stored pid is no more valid and the cxl driver is unable to handle faults as the mm_struct corresponding to process is no more accessible. This patch fixes this issue by using the mm_struct of the next alive task in the thread group. This is done by iterating over all the tasks in the thread group starting from thread group leader and calling get_task_mm on each one of them. When a valid mm_struct is obtained the pid of the associated task is stored in the context replacing the exiting one for handling future faults. The patch introduces a new function named get_mem_context that checks if the current task pointed to by ctx->pid is dead? If yes it performs the steps described above. Also a new variable cxl_context.glpid is introduced which stores the pid of the thread group leader associated with the context owning task. Reported-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com> Reported-by: NFrank Haverkamp <HAVERKAM@de.ibm.com> Suggested-by: NIan Munsie <imunsie@au1.ibm.com> Signed-off-by: NVaibhav Jain <vaibhav@linux.vnet.ibm.com> Acked-by: NIan Munsie <imunsie@au1.ibm.com> Reviewed-by: NFrederic Barrat <fbarrat@linux.vnet.ibm.com> Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
- 27 12月, 2015 5 次提交
-
-
由 Andrew Donnellan 提交于
Fix off-by-one error in opal_mce_check_early_recovery() when checking whether the NIP falls within OPAL space. Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Andrew Donnellan 提交于
A few of the config prompts for powerpc self-tests have periods at the end, which is inconsistent with the rest of the prompts. Remove the periods. Signed-off-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Michael Neuling 提交于
Only delay opal_rtc_read() when busy and are going to retry. This has the advantage of possibly saving a massive 10ms off booting! Kudos to Stewart for noticing. Signed-off-by: NMichael Neuling <mikey@neuling.org> Reviewed-by: NStewart Smith <stewart@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Russell Currey 提交于
On BMC machines, console output is controlled by the OPAL firmware and is only flushed when its pollers are called. When the kernel is in a panic state, it no longer calls these pollers and thus console output does not completely flush, causing some output from the panic to be lost. Output is only actually lost when the kernel is configured to not power off or reboot after panic (i.e. CONFIG_PANIC_TIMEOUT is set to 0) since OPAL flushes the console buffer as part of its power down routines. Before this patch, however, only partial output would be printed during the timeout wait. This patch adds a new kmsg_dumper which gets called at panic time to ensure panic output is not lost. It accomplishes this by calling OPAL_CONSOLE_FLUSH in the OPAL API, and if that is not available, the pollers are called enough times to (hopefully) completely flush the buffer. The flushing mechanism will only affect output printed at and before the kmsg_dump call in kernel/panic.c:panic(). As such, the "end Kernel panic" message may still be truncated as follows: >Call Trace: >[c000000f1f603b00] [c0000000008e9458] dump_stack+0x90/0xbc (unreliable) >[c000000f1f603b30] [c0000000008e7e78] panic+0xf8/0x2c4 >[c000000f1f603bc0] [c000000000be4860] mount_block_root+0x288/0x33c >[c000000f1f603c80] [c000000000be4d14] prepare_namespace+0x1f4/0x254 >[c000000f1f603d00] [c000000000be43e8] kernel_init_freeable+0x318/0x350 >[c000000f1f603dc0] [c00000000000bd74] kernel_init+0x24/0x130 >[c000000f1f603e30] [c0000000000095b0] ret_from_kernel_thread+0x5c/0xac >---[ end Kernel panic - not This functionality is implemented as a kmsg_dumper as it seems to be the most sensible way to introduce platform-specific functionality to the panic function. Signed-off-by: NRussell Currey <ruscur@russell.cc> Reviewed-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Michael Neuling 提交于
Currently we copy the whole mm_context_t to the paca but only access a few bits of it. This is wasteful of space paca and also takes quite some time in the hot path of context switching. This patch pulls in only the required bits from the mm_context_t to the paca and on context switch, copies only those. Benchmarking this (On top of Anton's recent MSR context switching changes [1]) using processes and yield shows an improvement of almost 3% on POWER8: http://ozlabs.org/~anton/junkcode/context_switch2.c ./context_switch2 --test=yield --process 0 0 1. https://lists.ozlabs.org/pipermail/linuxppc-dev/2015-October/135700.htmlSigned-off-by: NMichael Neuling <mikey@neuling.org> [mpe: Rename paca fields to be mm_ctx_foo rather than context_foo] Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
- 19 12月, 2015 1 次提交
-
-
由 Michael Neuling 提交于
This adds a function to copy the mm->context to the paca. This is only a basic conversion for now but will be used more extensively in the next patch. This also adds #ifdef CONFIG_PPC_BOOK3S around this code since it's not used elsewhere. Signed-off-by: NMichael Neuling <mikey@neuling.org> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
- 17 12月, 2015 20 次提交
-
-
由 Daniel Axtens 提交于
cppcheck picked up that there were a couple of missing va_end() calls in functions using va_start(). Signed-off-by: NDaniel Axtens <dja@axtens.net> Reviewed-by: NRussell Currey <ruscur@russell.cc> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Nathan Fontenot 提交于
Enable new kernel cpu hotplug functionality by allowing cpu dlpar requests to be initiated from sysfs. Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Nathan Fontenot 提交于
Add the ability to hotplug add cpus via rtas hotplug events by either specifying the drc index of the CPU to add, or providing a count of the number of CPUs to add. Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Nathan Fontenot 提交于
Add the ability to dlpar remove CPUs via hotplug rtas events, either by specifying the drc-index of the CPU to remove or providing a count of cpus to remove. To remove multiple cpus in a single request we create a list of possible DR (Dynamic Reconfiguration) cpus and their drc indexes that can be removed. We can then traverse the list remove each cpu and easily clean up in any cases of failure. Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Nathan Fontenot 提交于
Update the cpu dlpar add/remove paths to do better error recovery when a failure occurs during the add/remove operation. Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Nathan Fontenot 提交于
Re-factor the cpu hotplug code to support doing cpu hotplug completely in the kernel and using the existing sysfs probe/release interfaces. This patch pulls out pieces of existing cpu hotplug code into common routines, dlpar_cpu_add() and dlpar_cpu_remove(), to be used by both interfaces. There are no functional changes introduced. Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Nathan Fontenot 提交于
No functional changes, this patch is simply a move of the cpu hotplug code from pseries/dlpar.c to pseries/hotplug-cpu.c. This is in an effort to consolidate all of the cpu hotplug code in a common place. Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Nathan Fontenot 提交于
When DLPAR adding a CPU we should verify that the CPU does not already exist. Failure to do so can generate a kernel oops; [ 9.465585] kernel BUG at arch/powerpc/platforms/pseries/dlpar.c:382! [ 9.465796] Oops: Exception in kernel mode, sig: 5 [#1] This oops can be generated by causing a probe to be performed on a cpu by writing to the sysfs cpu probe file (/sys/devices/system/cpu/probe). This patch adds a check for the existence of cpu prior to probing the cpu so userspace doing the wrong thing won't trigger a BUG_ON(). Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Alistair Popple 提交于
PPC476FPE has a different PVR from previous PPC476 processors. The kexec code checks the PVR in order to correctly setup the MMU. When the initial support for 476FPE processors was added the corresponding change in the kexec code was missed. This patch simply adds the check and solves the following bug on kexec: kexec: Starting new kernel Bye! Unable to handle kernel paging request for instruction fetch Faulting instruction address: 0xee9a50f8 cpu 0x0: Vector: 400 (Instruction Access) at [ee9d7d20] pc: ee9a50f8 lr: ee9a50e4 sp: ee9d7dd0 msr: 21020 current = 0xee40f000 pid = 960, comm = kexec enter ? for help [link register ] ee9a50e4 [ee9d7dd0] c0013748 default_machine_kexec+0x58/0x70 (unreliable) [ee9d7df0] c0012f04 machine_kexec+0x34/0x40 [ee9d7e00] c00aa1ec kernel_kexec+0x9c/0xb0 [ee9d7e20] c005d704 SyS_reboot+0x1f4/0x220 [ee9d7f40] c000db68 ret_from_syscall+0x0/0x3c Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Alistair Popple 提交于
NVLink is a high speed interconnect that is used in conjunction with a PCI-E connection to create an interface between CPU and GPU that provides very high data bandwidth. A PCI-E connection to a GPU is used as the control path to initiate and report status of large data transfers sent via the NVLink. On IBM Power systems the NVLink processing unit (NPU) is similar to the existing PHB3. This patch adds support for a new NPU PHB type. DMA operations on the NPU are not supported as this patch sets the TCE translation tables to be the same as the related GPU PCIe device for each NVLink. Therefore all DMA operations are setup and controlled via the PCIe device. EEH is not presently supported for the NPU devices, although it may be added in future. Signed-off-by: NAlistair Popple <alistair@popple.id.au> Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Alistair Popple 提交于
Move __raw_rm_writeq() from platforms/powernv/pci-ioda.c to include/asm/io.h so that it can be used by other code. Signed-off-by: NAlistair Popple <alistair@popple.id.au> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Alistair Popple 提交于
This commit removed the pcidev field from struct pci_dn as it was no longer in use by the kernel. However to support finding the association of Nvlink devices to GPU devices from the device-tree this field is required. This reverts commit 250c7b27 ("powerpc/pci: Remove unused struct pci_dn.pcidev field"). Signed-off-by: NAlistair Popple <alistair@popple.id.au> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Gavin Shan 提交于
The name of PCI root bus's M64 resource isn't initialized properly. When dumping "/proc/iomem", "<BAD>" is seen for those M64 resources on PCI root buses. ~# cat /proc/iomem | grep -e "BAD" 3b0000000000-3b0fefffffff : <BAD> 3b1000000000-3b1fefffffff : <BAD> 3c0000000000-3c0fefffffff : <BAD> 3c1000000000-3c1fefffffff : <BAD> 3c2000000000-3c2fefffffff : <BAD> This fixes the issue by setting the name of PCI root bus's M64 resource to that of PHB's device node full name. With the patch, no "<BAD>" is seen from "/proc/iomem". Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Laurent Dufour 提交于
User space checkpoint and restart tool (CRIU) needs the page's change to be soft tracked. This allows to do a pre checkpoint and then dump only touched pages. This is done by using a newly assigned PTE bit (_PAGE_SOFT_DIRTY) when the page is backed in memory, and a new _PAGE_SWP_SOFT_DIRTY bit when the page is swapped out. To introduce a new PTE _PAGE_SOFT_DIRTY bit value common to hash 4k and hash 64k pte, the bits already defined in hash-*4k.h should be shifted left by one. The _PAGE_SWP_SOFT_DIRTY bit is dynamically put after the swap type in the swap pte. A check is added to ensure that the bit is not overwritten by _PAGE_HPTEFLAGS. Signed-off-by: NLaurent Dufour <ldufour@linux.vnet.ibm.com> CC: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Michael Ellerman 提交于
The STD_EXCEPTION_PSERIES macro takes both a vector number, and a location (memory address). However both are always identical, so combine them to save repeating ourselves. This does mean an exception handler must always exist at the location in memory that matches its vector number. But that's OK because this is the "STD" macro (standard), which does exactly that. We have other macros for the other cases, eg. STD_EXCEPTION_PSERIES_OOL (out of line). Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Michael Ellerman 提交于
This is only used in one location, open code it. Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Michael Ellerman 提交于
HMT_MEDIUM_LOW_HAS_PPR is only used in once place, open code it. Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Michael Ellerman 提交于
HMT_MEDIUM_PPR_DISCARD is a macro which is present at the start of most of our first level exception handlers. It conditionally executes a HMT_MEDIUM instruction, which sets the processor priority to medium. On on modern systems, ie. Power7 and later, it is nop'ed out at boot. All it does is make the exception vectors more cramped, and consume 4 bytes of icache. On old systems it has the effect of boosting the processor priority at the start of exception processing. If we were previously in the idle loop for example, we may be at low or very low priority. This is desirable as we want to process the exception as fast as possible. However looking closely at the generated code, we see that in all cases we execute another HMT_MEDIUM just four instructions later. With code patching applied, the final code on an old (Power6) system will look like, eg: c000000000000300 <data_access_pSeries>: c000000000000300: 7c 42 13 78 mr r2,r2 <- c000000000000304: 7d b2 43 a6 mtsprg 2,r13 c000000000000308: 7d b1 42 a6 mfsprg r13,1 c00000000000030c: f9 2d 00 80 std r9,128(r13) c000000000000310: 60 00 00 00 nop c000000000000314: 7c 42 13 78 mr r2,r2 <- So I suggest that the added code complexity of HMT_MEDIUM_PPR_DISCARD is not justified by the benefit of boosting the processor priority for the duration of four instructions, and therefore we drop it. Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Michael Ellerman 提交于
There are no longer any users of enter_rtas() outside of rtas.c, so make it "private", by moving the declaration inside rtas.c. Hopefully this will encourage people to use one of the wrappers which takes the sharp edges off the RTAS calling sequence. Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Michael Ellerman 提交于
Although call_rtas_display_status() does actually want to use the regular RTAS locking, it doesn't want the extra logic that is in rtas_call(), so currently it open codes the logic. Instead we can use rtas_call_unlocked(), after taking the RTAS lock. Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-