- 01 12月, 2012 6 次提交
-
-
由 Jan Glauber 提交于
CONFIG_PCI is disabled by default currently. Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Jan Glauber 提交于
Add some s390 specific sysfs attributes to the PCI device directory. The following attributes are introduced: - function_id (PCI function ID) - function_handle (PCI function handle) - pchid (PCI channel ID) - pfgid (PCI function group ID aka PCI root complex) Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Jan Glauber 提交于
Add SCLP PCI configure/deconfigure and implement a PCI hotplug controller (s390_pci_hpc). The hotplug controller creates a slot for every PCI function in stand-by or configured state. The PCI functions are named after the PCI function ID (fid). By writing to the power attribute in /sys/bus/pci/slots/<fid>/power the PCI function is moved to stand-by or configured state. If moved to the configured state the device is automatically scanned by the s390 PCI layer. Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Jan Glauber 提交于
Add CHSC store-event-information support for PCI (notfication type 2) and report error and availability events to the PCI architecture layer. Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Jan Glauber 提交于
Add DMA IOMMU support using 4K page table entries. Implement dma_map_ops. Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Jan Glauber 提交于
Support PCI adapter interrupts using the Single-IRQ-mode. Single-IRQ-mode disables an adapter IRQ automatically after delivering it until the SIC instruction enables it again. This is used to reduce the number of IRQs for streaming workloads. Up to 64 MSI handlers can be registered per PCI function. A hash table is used to map interrupt numbers to MSI descriptors. The interrupt vector is scanned using the flogr instruction. Only MSI/MSI-X interrupts are supported, no legacy INTs. Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 30 11月, 2012 3 次提交
-
-
由 Jan Glauber 提交于
The flogr instruction scans a bitmap starting from the leftmost bit. Implement support for these bitops. This could be useful to scan bitmaps like an interrupt vector set by the hardware starting at the leftmost bit. Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Jan Glauber 提交于
CLP instructions are used to query the firmware about detected PCI functions, the attributes of those functions and to enable or disable a PCI function. The CLP interface is the equivalent to a PCI bus scan. Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Jan Glauber 提交于
Add PCI support for s390, (only 64 bit mode is supported by hardware): - PCI facility tests - PCI instructions: pcilg, pcistg, pcistb, stpcifc, mpcifc, rpcit - map readb/w/l/q and writeb/w/l/q to pcilg and pcistg instructions - pci_iomap implementation - memcpy_fromio/toio - pci_root_ops using special pcilg/pcistg - device, bus and domain allocation Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 23 11月, 2012 15 次提交
-
-
由 Sebastian Ott 提交于
Allow drivers to enable/disable ccwgroup devices. Acked-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com> Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Christian Borntraeger 提交于
I was chasing down a bug of random validity intercepts on s390. (guest prefix page not mapped in the host virtual aspace). Turns out that the problem was a wrong address space control element. The cause was quite complex: During paging activity a DAT protection during SIE caused a program interrupt. Normally, the sie retry loop tries to catch all interrupts during and shortly before sie to rerun the setup. The problem is now that protection causes a suppressing program interrupt, causing the PSW to point to the instruction AFTER SIE in case of DAT protection. This confused the logic of the retry loop to not trigger, instead we jumped directly back to SIE after return from the program interrupt. (the protection fault handler itself did a rewind of the psw). This usually works quite well, but: If now the protection fault handler has to wait, another program might be scheduled in. Later on the sie process will be schedules in again. In that case the content of CR1 (primary address space) will be wrong because switch_to will put the user space ASCE into CR1 and not the guest ASCE. In addition the program parameter is also wrong for every protection fault of a guest, since we dont issue the SPP instruction. So lets also check for PSW == instruction after SIE in the program check handler. Instead of expensively checking all program interruption codes that might be suppressing we assume that a program interrupt pointing after SIE was always a program interrupt in SIE. (Otherwise we have a kernel bug anyway). We also have to compensate the rewinding, since the C-level handlers will do that. Therefore we need to add a nop with the same length as SIE before the sie_loop. Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com> CC: stable@vger.kernel.org CC: Heiko Carstens <heiko.carstens@de.ibm.com>
-
由 Martin Schwidefsky 提交于
The current single step code is racy in regard to concurrent delivery of signals. If a signal is delivered after a PER program check occurred but before the TIF_PER_TRAP bit has been checked in entry[64].S the code clears TIF_PER_TRAP and then calls do_signal. This is wrong, if the instruction completed (or has been suppressed) a SIGTRAP should be delivered to the debugger in any case. Only if the instruction has been nullified the SIGTRAP may not be send. The new logic always sets TIF_PER_TRAP if the program check indicates PER tracing but removes it again for all program checks that are nullifying. The effect is that for each change in the PSW address we now get a single SIGTRAP. Reported-by: NAndreas Arnez <arnez@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
-
由 Heiko Carstens 提交于
Allow to generate code that only runs on zEC12 machines. Also add a check which prevents the kernel to run on machines which do not have any of the following new facilities installed: - (48) decimal-floating-point zoned-conversion - (49) execution-hint - (49) load-and-trap - (49) miscellaneous-instruction-extensions - (49) processor-assist - (50) constrained transactional-execution - (73) transactional-execution 48, 49, 50 and 73 are the bit numbers of the facility indications for each of the required facilities. Note that we assume that user-space gets compiled with the same compiler options, therefore we also test for a dfp facility even if the kernel doesn't make use of it. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
-
由 Heiko Carstens 提交于
Mainly merge all different per-cpu arrays into a single array which holds all topology information per logical cpu. Also fix the broken core vs socket variable naming and simplify the locking a bit. When running in environments without topology information also invent book, socket and core ids, so that not all ids are zero. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Keep related functions together and move to appropriate file. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Move and rename init_storage_keys() to pageattr.c, so it can also be used from the sclp memory hotplug code in order to initialize storage keys. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Just convert fault_init() to an early initcall. That's still early enough since it only needs be called before user space processes get executed. No reason to externalize it. Also add the function to the init section and move the store_indication variable to the read_mostly section. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
Let the dasd driver and qdio use ccw_device_get_schid and get rid of other similar functions. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Cornelia Huck 提交于
This will be needed by the new virtio-ccw transport. Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Jan Glauber 提交于
Remove the BUG_ON's that check for failure or incomplete results of the s390 hardware crypto instructions. Rather report the errors as -EIO to the crypto layer. Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Preinitialize the program check table, so we can put it into the read-only data section. Also use only four byte entries for the table, since each program check handler resides within the first 2GB. Therefore this reduces the size of the table by 50% on 64 bit builds. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Use 1MB frames for vmemmap if EDAT1 is available in order to reduce TLB pressure Always use a 1MB frame even if its only partially needed for struct pages. Otherwise we would end up with a mix of large frame and page mappings, because vmemmap_populate gets called for each section (256MB -> 3.5MB memmap) separately. Worst case is that we would waste 512KB. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Use 2GB frames for indentity mapping if EDAT2 is available to reduce TLB pressure. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 13 11月, 2012 3 次提交
-
-
由 Heiko Carstens 提交于
Select HAVE_ALIGNED_STRUCT_PAGE on s390, so that the slub allocator can make use of compare and swap double for lockless updates. This increases the size of struct page to 64 bytes (instead of 56 bytes), however the performance gain justifies the increased size: - now excactly four struct pages fit into a single cache line; the case that accessing a struct page causes two cache line loads does not exist anymore. - calculating the offset of a struct page within the memmap array is only a simple shift instead of a more expensive multiplication. A "hackbench 200 process 200" run on a 32 cpu system did show an 8% runtime improvement. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
access_ok() returns always "true" on s390. Therefore all access_ok() invocations are rather pointless. However when walking page tables we need to make sure that everything is within bounds of the ASCE limit of the task's address space. So remove the access_ok() call and add the same check we have in get_user_pages_fast(). Reviewed-by: NGerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
When walking page tables we need to make sure that everything is within bounds of the ASCE limit of the task's address space. Otherwise we might calculate e.g. a pud pointer which is not within a pud and dereference it. So check against TASK_SIZE (which is the ASCE limit) before walking page tables. Reviewed-by: NGerald Schaefer <gerald.schaefer@de.ibm.com> Cc: stable@vger.kernel.org Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 12 11月, 2012 2 次提交
-
-
由 Heiko Carstens 提交于
The current topology code confuses core id vs physical package id. In other words /sys/devices/system/cpu/cpuX/topology/core_id displays the physical_package_id (aka socket id) instead of the core id. The physical_package_id sysfs attribute always displays "-1" instead of the socket id. Fix this mix-up with a small patch which defines and initializes topology_physical_package_id correctly and fixes the broken core id handling. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Martin Schwidefsky 提交于
If user space is running in primary mode it can switch to secondary or access register mode, this is used e.g. in the clock_gettime code of the vdso. If a signal is delivered to the user space process while it has been running in access register mode the signal handler is executed in access register mode as well which will result in a crash most of the time. Set the address space control bits in the PSW to the default for the execution of the signal handler and make sure that the previous address space control is restored on signal return. Take care that user space can not switch to the kernel address space by modifying the registers in the signal frame. Cc: stable@vger.kernel.org Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 07 11月, 2012 2 次提交
-
-
由 Heiko Carstens 提交于
The early mini sclp driver may be called in zArch mode either in 31 or 64 bit addressing mode. If called in 31 bit addressing mode the new external interrupt psw however would switch to 64 bit addressing mode. This would cause an addressing exception within the interrupt handler, since the code didn't expect the zArch/31 bit addressing mode combination. Fix this by setting the new psw addressing mode bits so they fit the current addressing mode. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Cornelia Huck 提交于
There's no need to keep __MAX_SUBCHANNEL and __MAX_SSID private to the common I/O layer when __MAX_CSSID is usable by everybody. Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 26 10月, 2012 2 次提交
-
-
由 Gerald Schaefer 提交于
Similar to pte_none() and pte_present(), the pmd functions should also respect page protection of huge pages, especially PROT_NONE. This patch also simplifies massage_pgprot_pmd() by adding new definitions for huge page protection. Signed-off-by: NGerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Gerald Schaefer 提交于
Without CONFIG_HUGETLB_PAGE, pmd_huge() will always return 0. So pmd_large() should be used instead in places where both transparent huge pages and hugetlbfs pages can occur. Signed-off-by: NGerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 19 10月, 2012 1 次提交
-
-
由 David Howells 提交于
It turns out that S390 shouldn't use uapi/asm-generic/kvm_para.h since it defines the functions in its non-UAPI kvm_para.h file. #including <asm-generic/kvm_para.h> will first pick up include/asm-generic/kvm_para.h, which defines conflicting functions. Instead, partially revert commit 0420c87e, ungenericising this file and just inserting a comment to prevent the patch program from deleting it. cc: Yuanhan Liu <yuanhan.liu@intel.com> cc: fengguang.wu@intel.com Reported-by: NYuanhan Liu <yuanhan.liu@intel.com> Signed-off-by: NDavid Howells <dhowells@redhat.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 18 10月, 2012 6 次提交
-
-
由 Heiko Carstens 提交于
The sysfs and procfs output of the instruction and data caches were wrong: the output of the data cache provided that instruction cache values and vice versa. Fix this by using the correct type indication when issueing the ecag instruction. Reported-by: NAndreas Krebbel <Andreas.Krebbel@de.ibm.com> Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Because of a change in the s390 arch backend of binutils (commit 23ecd77 "Pick the default arch depending on the target size" in binutils repo) 31 bit builds will fail since the linker would now try to create 64 bit binary output. Fix this by setting OUTPUT_ARCH to s390:31-bit instead of s390. Thanks to Andreas Krebbel for figuring out the issue. Fixes this build error: LD init/built-in.o s390x-4.7.2-ld: s390:31-bit architecture of input file `arch/s390/kernel/head.o' is incompatible with s390:64-bit output Cc: Andreas Krebbel <Andreas.Krebbel@de.ibm.com> Cc: stable@vger.kernel.org Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Gerald Schaefer 提交于
Add missing select statement to arch/s390/Kconfig. Signed-off-by: NGerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Michael Holzheu 提交于
The 0x10000 entry point can be called in z/Arch architecture and 64 bit addressing mode. Therefore this patch removes the unnecessary 31 bit switch code from the kdump startup function. Signed-off-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Hendrik Brueckner 提交于
Increase the maximum number of available counters and check if the hardware supports the counter. Support is indicated by the version of the CPU-measurement counter facility. Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
Add back a hunk from "4dcc2a4d s390/chsc: make headers usable" which was lost during the merge of the UAPI patch. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-