Signed-off-by: NDeepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new short message format is used on the new BCM57454 VFs.  Each
firmware message is a fixed 16-byte message sent using the standard
firmware communication channel.  The short message has a DMA address
pointing to the legacy long firmware message.
Signed-off-by: NDeepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the current code, bnxt_dcb_init() is called too early before we
determine if the firmware DCBX agent is running or not.  As a result,
we are not setting the DCB_CAP_DCBX_HOST and DCB_CAP_DCBX_LLD_MANAGED
flags properly to report to DCBNL.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the SPARC platform we need to use the DMA_ATTR_WEAK_ORDERING attribute
in our Rx path dma mapping in order to get the expected performance out
of the receive path.  Adding it to the Tx path has little effect, so
that's not a part of this patch.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Reviewed-by: NTushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: NTom Saeger <tom.saeger@oracle.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have the number of longs, but we need to calculate the number of
bytes required.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change restricts the PF in multi-host mode from setting any port
level PHY configuration.  The settings are controlled by firmware in
Multi-Host mode.
Signed-off-by: NDeepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check the additional flag in bnxt_hwrm_func_qcfg() before allowing
DCBX to be done in host mode.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for 100G link speed reporting for Broadcom BCM57454
ASIC in ethtool command.
Signed-off-by: NDeepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: NRay Jui <ray.jui@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code enables up to the maximum MSIX vectors in the PCIE
config space without considering the max completion rings available.
An MSIX vector is only useful when it has an associated completion
ring, so it is better to cap it.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mac loopback self test operates in polling mode.  To support that,
we need to add functions to open and close the NIC half way.  The half
open mode allows the rings to operate without IRQ and NAPI.  We
use the XDP transmit function to send the loopback packet.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the basic infrastructure and only firmware tests initially.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add suspend/resume callbacks using the newer dev_pm_ops method.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And add functions to set and free magic packet filter.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add pci shutdown method to put device in the proper WoL and power state.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add code to driver probe function to check if the device is WoL capable
and if Magic packet WoL filter is currently set.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnxt_free_rx_skbs(), which is called to free up all RX buffers during
shutdown, we need to unmap the page if we are running in XDP mode.

Fixes: c61fb99c ("bnxt_en: Add RX page mode support.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSankar Patchineelam <sankar.patchineelam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Net device reset can fail when the h/w or f/w is in a bad state.
Subsequent netdevice open fails in bnxt_hwrm_stat_ctx_alloc().
The cleanup invokes bnxt_hwrm_resource_free() which inturn
calls bnxt_disable_int().  In this routine, the code segment

if (ring->fw_ring_id != INVALID_HW_RING_ID)
   BNXT_CP_DB(cpr->cp_doorbell, cpr->cp_raw_cons);

results in NULL pointer dereference as cpr->cp_doorbell is not yet
initialized, and fw_ring_id is zero.

The fix is to initialize cpr fw_ring_id to INVALID_HW_RING_ID before
bnxt_init_chip() is invoked.
Signed-off-by: NSankar Patchineelam <sankar.patchineelam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.

This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.

Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some situations, the firmware will return 0 for autoneg supported
speed.  This may happen if the firmware detects no SFP module, for
example.  The driver should ignore this so that we don't end up with
an invalid autoneg setting with nothing advertised.  When SFP module
is inserted, we'll get the updated settings from firmware at that time.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set DCB_CAP_DCBX_HOST capability flag only if the firmware LLDP agent
is not running.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we call bnxt_reset_task() due to tx timeout, we should call
bnxt_ulp_stop() to inform the RDMA driver about the error and the
impending reset.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware call to do function reset is done too late.  It is causing
the rings that have been reserved to be freed.  In NPAR mode, this bug
is causing us to run out of rings.

Fixes: 391be5c2 ("bnxt_en: Implement new scheme to reserve tx rings.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use eth_hw_addr_random() to set a random MAC address in order to make
sure bp->dev->addr_assign_type will be properly set to NET_ADDR_RANDOM.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the bnxt_init_one() failure path, bar1 and bar2 are not
being unmapped.  This commit fixes this issue.  Reorganize the
code so that bnxt_init_one()'s failure path and bnxt_remove_one()
can call the same function to do the PCI cleanup.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If bnxt_hwrm_ring_free() is called during a failure path in bnxt_open(),
it is possible that the completion rings have not been allocated yet.
In that case, the completion doorbell has not been initialized, and
calling bnxt_disable_int() will crash.  Fix it by checking that the
completion ring has been initialized before writing to the completion
ring doorbell.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are additional SoC devices that use the same device ID for
bridge and NIC devices.  The bnxt driver should reject probe against
all bridge devices since it's meant to be used with only endpoint
devices.
Signed-off-by: NRay Jui <ray.jui@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDeepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add proper puctuation to make the message more clear.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Print FEC (Forward Error Correction) autoneg and encoding settings during
link up.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If it is a VF or an NPAR function, the firmware call to setup the PHY
will fail.  Adding this check will prevent unnecessary firmware calls
to setup the PHY unless calling from the PF.  This will also eliminate
many unnecessary warning messages when the call from a VF or NPAR fails.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If skb_flow_dissect_flow_keys() returns with the encapsulation flag
set, pass the information to the firmware to setup the NTUPLE filter
accordingly.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit ae10ae74 ("bnxt_en: Add new hardware RFS mode.") has added
code to allow NTUPLE to be enabled on VFs.  So we now remove the
BNXT_VF() check in rfs_capable() to allow NTUPLE on VFs.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new spec has NVRAM defragmentation support which will be used in
the next patch to improve ethtool flash operation.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add dedicated transmit function and transmit completion handler for
XDP.  The XDP transmit logic and completion logic are different than
regular TX ring.  The TX buffer is recycled back to the RX ring when
it completes.

v3: Improved the buffer recyling scheme for XDP_TX.

v2: Add trace_xdp_exception().
    Add dma_sync.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Tested-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add basic ndo_xdp support to setup and query program, configure the NIC
to run in rx page mode, and support XDP_PASS, XDP_DROP, XDP_ABORTED
actions only.

v3: Pass modified offset and length to stack for XDP_PASS.
    Remove Kconfig option.

v2: Added trace_xdp_exception()
    Added dma_syncs.
    Added XDP headroom support.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Tested-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

XDP_TX requires a different function to handle completion.  Add a
function pointer to handle tx completion logic.  Regular TX rings
will be assigned the current bnxt_tx_int() for the ->tx_int()
function pointer.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add logic for an extra set of TX rings for XDP.  If enabled, this
set of TX rings equals the number of RX rings and shares the same
IRQ as the RX ring set.  A new field bp->tx_nr_rings_xdp is added
to keep track of these TX XDP rings.  Adjust all other relevant functions
to handle bp->tx_nr_rings_xdp.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support XDP_TX, we need to add a set of dedicated TX rings, each
associated with the NAPI of an RX ring.  To assign XDP rings and regular
rings in a flexible way, we add a bp->tx_ring_map[] array to do the
remapping.  The netdev txq index is stored in the new field txq_index
so that we can retrieve the netdev txq when handling TX completions.
In this patch, before we introduce XDP_TX, the mapping is 1:1.

v2: Fixed a bug in bnxt_tx_int().
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, bnxt_setup_tc() and bnxt_set_channels() have similar and
duplicated code to check and reserve rx and tx rings.  Add a new
function bnxt_reserve_rings() to centralize the logic.  This will
make it easier to add XDP_TX support which requires allocating a
new set of TX rings.

Also, the tx ring checking logic in bnxt_setup_msix() can be removed.
The rings have been reserved before hand.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>