The current drivers return errors from this calldown
wrapped in an ERR_PTR().

The rdmavt code incorrectly tests for NULL.

The code is fixed to use IS_ERR() and change ret according
to the driver return value.

Cc: Stable <stable@vger.kernel.org> # 4.6+
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Since rvt_reset_qp already zero's out qp->s_ack_queue head and tail
pointers, there is no need to zero out qp->s_ack_queue itself.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NAshutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

A failure in the get_txreq() inline will result in a
slow path retry using __get_txreq().

__get_txreq() attempts to procure the qp s_lock, which
is already held in all callers.

Fix by deleting the s_lock maintenance in __get_txreq()
and add sparse syntax hooks to future proof the code.

Cc: Stable <stable@vger.kernel.org> # 4.6+
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Swapping a cable from a "Mgmt Allowed=No" switch port to a
"Mgmt Allowed=Yes" switch port doesn't send a pkey change
notification. Therefore, the link doesn't become active as
the oib_utils layer uses an old pkey table cache.

Fix by ensuring the pkey change notification is sent when
the table is changed both explicitly by the FM and implicitly
by the driver via a cable swap.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

FULL_MGMT_P_KEY doesn't get cleared from the pkey table at link bounce
because the link down and link bounce code paths are different when
moving a QSFP cable on a switch. This causes an HFI unit connected to a
switch to try to be initialized to an FM node when the QSFP cable is
moved from a MgmtAllowed=NO port to a MgmtAllowed=YES port and back to a
MgmtAllowed=NO port. Remove FULL_MGMT_P_KEY from pkey table at link up.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This fixes potential buffer overflow because the sprintf function
doesn't check buffer boundaries. Use snprintf instead.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This fixes potential NULL ptr dereference because IS_ERR(dd) doesn't
handle NULL. Fix the issue by initializing the pointer with a not NULL
error code.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

If a context has already been assigned to an FD, prevent
another assignment.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

If a context has already been assigned to an FD, prevent
another assignment.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The current value of 500us for the packet egress timeout is too small
which causes the host to declare failure on draining packets too early
and unnecessarily bounces the link. Increase this to 50ms taking into
account the switch packet discard timer default and the worst case
per-VL package drainage rate.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Correct calculation of the low order bits which should be unset
based on use of qos_shift parameter when assigning QPN.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NBrian Welty <brian.welty@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Functions required for MODIFY_PORT were incorrectly being
required for MODIFY_QP.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NBrian Welty <brian.welty@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The credit return threshold adjustment on mtu change algorithm does not
take into account all the kernel send contexts that are assigned per VL.
Use the pio send context map to adjust the credit return thresholds for
all the allocated and assigned kernel send contexts based on the MTU
adjustment per VL.

The pio send context map can be changed dynamically based on the actual
number of operational vls which is set by the fabric manager. When this
happens update the credit return threshold values for all the remapped
kernel send contexts.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NJianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

ipoib_neigh_get unconditionally updates the "alive" variable member on
any packet send.  This prevents the neighbor garbage collection from
cleaning out a dead neighbor entry if we are still queueing packets
for it.  If the queue for this neighbor is full, then don't update the
alive timestamp.  That way the neighbor can time out even if packets
are still being queued as long as none of them are being sent.

Fixes: b63b70d8 ("IPoIB: Use a private hash table for path lookup in xmit path")
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Userspace flag IBV_QP_ALT_PATH is supposed to set the alternate path
including fields alt_pkey_index and alt_timeout.
Added IB_QP_PKEY_INDEX and IB_QP_TIMEOUT to the attribute mask when
calling mlx5_set_path for the alternate path to force setting the
alt_pkey_index and alt_timeout values.

Fixes: bf24481a3a7c4 ('IB/mlx5: Consider alternate path in pkey ...')
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Pkey index fields in the QP context path record are extended to 16
bits, as required by IB spec (version 1.3).
This change affects all QP commands which include path records.

To enable this change, moved the free adaptive routing flag bit
(free_ar) to the most significant byte of the QP path record.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB ...')
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Verify that number of entries is less than device capability.
Add an appropriate warning message for error flow.

Fixes: bde51583 ('IB/mlx5: Add support for resize CQ')
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Number of entries shouldn't be greater than the device's max
capability. This should be checked before rounding the entries number
to power of two.

Fixes: 51ee86a4 ('IB/mlx5: Fix check of number of entries...')
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

BlueFlame support is reported only for PFs when the HCA capability is
on.

Fixes: 938fe83c ('net/mlx5_core: New device capabilities...')
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Some variables were not initialized properly: max_recv_wr,
max_recv_sge, max_send_wr, qp_context and max_inline_data.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB...')
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When PAGE_SIZE is larger than 4K, the user shouldn't be able to query
the HCA core clock. This counter is within 4KB boundary and the
user-space shall not read information that's after this boundary.

Fixes: b368d7cb ('IB/mlx5: Add hca_core_clock_offset to...')
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add a 4-digit padding to show FW version in proper format.

Fixes: 9603b61d ('mlx5: Move pci device handling from...')
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

FW port-change events are fired on Active <-> non Active port state
transitions only.
When the port state changes from Active to Initializing (Active ->
Down -> Initializing), a single event is fired.
The HCA transitions from Down to Initializing unless prevented from
doing so, hence the driver should also propagate events when the port
state is Initializing to consumers so they'll be aware that the port
is no longer Active and act accordingly.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB...')
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Flow steering is supported by mlx5 device when the following
features are supported by firmware:

1. NIC RX flow table.
2. Device has enough flow steering levels.
3. Atomic modification of flow table entry.
4. Flow tables chaining.

To check if flow steering is supported it's enough to check
if the driver opened the mlx5 bypass namespace.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Replace the few u64 casts with ULL to match the rest of the casts.
Signed-off-by: NMax Gurtovoy <maxg@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

ib_device_cap_flags 64-bit expansion caused caps overlapping
and made consumers read wrong device capabilities. For example
IB_DEVICE_SG_GAPS_REG was falsely read by the iser driver causing
it to use a non-existing capability. This happened because signed
int becomes sign extended when converted it to u64. Fix this by
casting IB_DEVICE_ON_DEMAND_PAGING enumeration to ULL.

Fixes: f5aa9159 ('IB/core: Add arbitrary sg_list support')
Reported-by: NRobert LeBlanc <robert@leblancnet.us>
Cc: Stable <stable@vger.kernel.org> #[v4.6+]
Acked-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NMax Gurtovoy <maxg@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

For dynamically allocated sysfs attributes there is a need to call
sysfs_attr_init in order to comply with lockdep, not calling it
will result in error complaining key is not in .data section.

Fixes: b40f4757 ("IB/core: Make device counter infrastructure dynamic")
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Align locking usage when touching device address with rest
of the kernel. Lock the bottom half when doing so using
netif_addr_lock_bh.

This also solves the following case as reported by lockdep:
	CPU0                    CPU1
	----                    ----
lock(_xmit_INFINIBAND);
				local_irq_disable();
				lock(&(&mc->mca_lock)->rlock);
				lock(_xmit_INFINIBAND);
<Interrupt>
lock(&(&mc->mca_lock)->rlock);

*** DEADLOCK ***

Fixes: 492a7e67 ("IB/IPoIB: Allow setting the device address")
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When deleting a default GID from the cache, its gid_type field is set
to 0.

This could set the gid_type to RoCE v1 for a RoCE v2 default GID,
essentially making it inaccessible to future modifications, since it
is no longer found by find_gid().

This fix preserves the gid_type value for default gids during cache
operations.

Fixes: b39ffa1d ('IB/core: Add gid_type to gid attribute')
Signed-off-by: NAviv Heller <avivh@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

In ipoib_remove_one the driver holds the rtnl_lock and tries to do some
operation like dev_change_flags or unregister_netdev, while sysfs
callback like ipoib_vlan_delete holds sysfs mutex and tries to hold the
rtnl_lock via rtnl_trylock() and restart_syscall() if the lock is not
free, meanwhile ipoib_remove_one tries to get the sysfs lock in order to
free its sysfs directory, and we will get  a->b, b->a deadlock.

    Trace like the following:

        schedule+0x37/0x80
        schedule_preempt_disabled+0xe/0x10
        __mutex_lock_slowpath+0xb5/0x120
        mutex_lock+0x23/0x40
        rtnl_lock+0x15/0x20
        netdev_run_todo+0x17c/0x320
        rtnl_unlock+0xe/0x10
        ipoib_vlan_delete+0x11b/0x1b0 [ib_ipoib]
        delete_child+0x54/0x80 [ib_ipoib]
        dev_attr_store+0x18/0x30
        sysfs_kf_write+0x37/0x40
        mutex_lock+0x16/0x40
        SyS_write+0x55/0xc0
        entry_SYSCALL_64_fastpath+0x16/0x75
    And
        schedule+0x37/0x80
        __kernfs_remove+0x1a8/0x260
        ? wake_atomic_t_function+0x60/0x60
        kernfs_remove+0x25/0x40
        sysfs_remove_dir+0x50/0x80
        kobject_del+0x18/0x50
        device_del+0x19f/0x260
        netdev_unregister_kobject+0x6a/0x80
        rollback_registered_many+0x1fd/0x340
        rollback_registered+0x3c/0x70
        unregister_netdevice_queue+0x55/0xc0
        unregister_netdev+0x20/0x30
        ipoib_remove_one+0x114/0x1b0 [ib_ipoib]
        ib_unregister_client+0x4a/0x170 [ib_core]
        ? find_module_all+0x71/0xa0
        ipoib_cleanup_module+0x10/0x94 [ib_ipoib]
        SyS_delete_module+0x1b5/0x210
        entry_SYSCALL_64_fastpath+0x16/0x75

The fix is by checking the flag IPOIB_FLAG_INTF_ON_DESTROY in order to
get out from the sysfs function.

Fixes: 862096a8 ("IB/ipoib: Add more rtnl_link_ops callbacks")
Fixes: 9baa0b03 ("IB/ipoib: Add rtnl_link_ops support")
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Currently ib_query_port always attempts to to read the subnet prefix by
calling ib_query_gid(). For RoCE/iWARP there is no subnet manager and no
subnet prefix. Fix this by querying GID[0] only for IB networks.

Fixes: fad61ad4 ('IB/core: Add subnet prefix to port info')
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Reviewed-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Between the initial and final versions of the function setup_hw_stats,
the order of variable initialization was changed.  However, the unwind
flow on error did not properly keep up with the flow changes.  Make
the unwind flow match a proper unwind of the allocation flow, then
remove no longer needed variable initializations.

Fixes: b40f4757 (IB/core: Make device counter infrastructure
dynamic)
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The new sysfs hw_counters code had an off by one in its array allocation
length.  Fix that and the comment along with it.
Reported-by: NMark Bloch <markb@mellanox.com>
Fixes: b40f4757 (IB/core: Make device counter infrastructure
dynamic)
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Avoid that sparse reports the following warnings for the hfi1 driver:

trace.c:217:13: warning: no previous prototype for ‘print_u64_array’ [-Wmissing-prototypes]
user_sdma.c:1361:17: warning: dubious: !x & y
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The first argument of test_bit() and clear_bit() is a bit number and
not a bitmask. Hence change that first argument from (1 << 0) into 0.
This patch avoids that smatch reports the following warnings:

user_sdma.c:1059: sdma_cache_evict() warn: test_bit() takes a bit number
user_sdma.c:1590: sdma_rb_remove() warn: test_bit() takes a bit number
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Make the indentation of the source code consistent. Detected by
smatch.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This patch avoids that sparse reports the following warning:

rdmavt/qp.c:507:17: warning: context imbalance in 'rvt_reset_qp' - unexpected unlock
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Make indentation consistent. Detected by smatch.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Hal Rosenstock <hal@mellanox.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Reviewed-By: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NHal Rosenstock <hal@mellanox.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Make indentation consistent. Detected by smatch.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: NSteve Wise <swise@opengridcomputing.com>
Reviewed-by: NSagi Grimberg <sagi@gimberg.me>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Because patch "IB/srp: Move common code into the caller" was applied
partially srp_map_sg_dma() doesn't work properly. Fix this by
applying the remainder of that patch. See also
http://thread.gmane.org/gmane.linux.drivers.rdma/35803/focus=35811.

Fixes: 3849e44d ("IB/srp: Move common code into the caller")
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Sagi Grimberg <sai@grimberg.me>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Laurence Oberman <loberman@redhat.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDoug Ledford <dledford@redhat.com>