In the receive path a spinlock is taken upon parsing the TLV signal
header. This moves to locking to the TLV handling functions where
it protects the data structures.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Trivial cleanup of debug messages.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Transmit packets needs to be tagged in order to receive a tx status
feedback from the firmware. Determine the tag in the netdev transmit
callback instead of determining the tag just before transfer to the
device. This reduces the number of exception flows and hence makes
the driver code simpler.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

DMA engine of some old SDIO host controllers require block size alignment for
data length of each scatterlist item. This patch introduces an intermediate
buffer list to support this kind of platform. It decreases the throughput
because of an extra memcpy in critical data path. So don't turn this on unless
it's necessary.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Introduce a unified dongle backplane address preparation function
brcmf_sdio_addrprep to replace duplicate address prep code.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove SDIO_REQ_ASYNC from brcmfmac since it is not being used.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Used NL80211_NUM_ACS to indicate the BCMC fifo used in the driver
which has the same value now, but it is a bad idea relying on that.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When getting a transmit packet from the networking layer simply
enqueue the packet unconditional and have it handled by the dequeue
worker. The transfer of the packet to the bus-specific driver part
is now done from one context.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This allows enabling support for extra hardware with just a module
param, without kernel/module recompilation.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Apparently HW doesn't require us to generate MMIC
for TKIP suite.

Each frame was 8 bytes longer than it should be
and some APs would drop frames that exceed 1520
bytes of 802.11 payload. This could be observed
during throughput tests or fragmented IP traffic.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Nonsense channel flags were being set.

Although it doesn't seem this was visible to the
user the patch makes sure that channel
availability won't be crippled in the future if
ath_common behaviour changes.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Irqs were not freed up correctly upon msi-x setup
failure.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code writes the default_power2 value into the TX field
of the RFCSR50 register, however the condition in the if
statement uses default_power1. Due to this, wrong TX power
value might be written into the register.

Use the correct value in the condition to fix the issue.

Compile tested only.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org # 3.10
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 3T/3R devices are using the tertiary PAs/LNAs
however those are never turned on. Fix the code to
turn on those on for such devices.

Also modify the code to use switch statements to
improve readability.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The secondary PAs/LNAs are turned on only for 2T/2R
devices, however these are used for 3T/3R devices as
well. Always turn those on if the device uses more
than one tx/rx chains.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NStanislaw Gruszka <stf_xl@wp.pl>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ralink 3T chipsets are using a different EEPROM
layout than the others. The EEPROM on these devices
contain more data than the others which does not fit
into 272 byte which the rt2800 driver actually uses.

The Ralink reference driver defines EEPROM_SIZE to
512/1024 bytes for PCI/USB devices respectively.

Increase the EEPROM_SIZE constant to 512 bytes, in
order to make room for EEPROM data of 3T devices.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NStanislaw Gruszka <stf_xl@wp.pl>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To improve power consumption in idle associated mode FW may lower
RX power. This low linearity mode is acceptable for listening low rate
RX such as beacons and groupcast. The driver enables LPRX only if PM
is enabled and associated AP's beacon TX rate is 1Mbps or 6Mbps.
LPRX RSSI threshold is used to limit a range where LPRX is applied.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A few places use 'pcie_trans' which is a bit non-standard,
use 'trans_pcie' there as well.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A few places use just 'q', use 'rxq' there like all
other places.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The PCIe code has an array of buffer descriptors (RXBs) that have pages
and DMA mappings attached. In regular use, the array isn't used and the
buffers are either on the hardware receive queue or the rx_free/rx_used
lists for recycling.

Occasionally, during module unload, we'd see a warning from this:

WARNING: at lib/list_debug.c:32 __list_add+0x91/0xa0()
list_add corruption. prev->next should be next (c31c98cc), but was c31c80bc. (prev=c31c80bc).
Pid: 519, comm: rmmod Tainted: G        W  O 3.4.24-dev #3
Call Trace:
 [<c10335b2>] warn_slowpath_common+0x72/0xa0
 [<c1033683>] warn_slowpath_fmt+0x33/0x40
 [<c12e31d1>] __list_add+0x91/0xa0
 [<fdf2083c>] iwl_pcie_rxq_free_rbs+0xcc/0xe0 [iwlwifi]
 [<fdf21b3f>] iwl_pcie_rx_free+0x3f/0x210 [iwlwifi]
 [<fdf2dd7a>] iwl_trans_pcie_free+0x2a/0x90 [iwlwifi]

The reason for this seems to be that in iwl_pcie_rxq_free_rbs() we use
the array to free all buffers (the hardware receive queue isn't in use
any more at this point). The function also adds all buffers to rx_used
because it's also used during initialisation (when no freeing happens.)
This can cause the warning because it may add entries to the list that
are already on it. Luckily, this is harmless because it can only happen
when the entire data structure is freed anyway, since during init both
lists are initialized from scratch.

Disentangle this code and treat init and free separately. During init
we just need to put them onto the list after freeing all buffers (for
switching between 4k/8k buffers); during free no list manipulations
are necessary at all.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In case that an AP/GO interface is started while there is a
station/P2P client associated, need to make sure that the AP/GO
beacon time is far enough from the station's one in oder to allow
the station to receive the DTIM beacons and the following traffic
etc.

To resolve this, when the AP is started, check if there is an
active station interface, and guarantee that the AP/GO TBTT is far
enough from the station one.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add prints visible to the user when entering and exiting
thrermal throttling, because so users can tell that the
NIC is getting too hot (and throughput will decrease.)
Signed-off-by: Neytan lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

1x1 products will need a special LUT.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Various parts of the HW code are applicable for
both v2.0 and v2.1.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver loads its firmware from files rtlwifi/rtl8723fw*.bin, but the
MODULE_FIRMWARE macros refer to rtlwifi/RTL8723aefw*.bin.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>  [3.8+]
Reported-by: NAxel Köllhofer <AxelKoellhofer@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Map BIT 9 in TX DMA DWARD 0 as HW write back option.
We must turn on this option in the last TX descriptor,
this is required for old HW compatability.
This option indicate to HW that WB is required for this descriptor.
Signed-off-by: NKirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The vring index (MAC queue id) must be set in all TX descriptors
otherwise HW will fail to release descriptors for a specific vring
(disconnect or vring switch flows).
This is normally occurs when fragmentation required, if vring index
will not be the same for all SKB descriptors HW will fail to flush
this MAC queue.
Signed-off-by: NKirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use common names instead of chip specific ones.
The patch contains no functional changes, but
it makes it easier to add support for further
descriptor sizes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NStanislaw Gruszka <stf_xl@wp.pl>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Different chipsets may use different TXWI descriptor
size. Instead of using a hardcoded value, use the
'queue->winfo_size' which holds the correct value for
a given device.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NStanislaw Gruszka <stf_xl@wp.pl>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current code uses the same index value both
for the channel information array and for the TX
power table. The index starts from 14, however the
index of the TX power table must start from zero.

Fix it, in order to get the correct TX power value
for a given channel.

The changes in rt61pci.c and rt73usb.c are compile
tested only.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Acked-by: NStanislaw Gruszka <stf_xl@wp.pl>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>