The Iomega Jaz USB Adapter is a SCSI-USB converter cable. The hardware
seems to be identical to e.g. the Microtech XpressSCSI, using a Shuttle/
SCM chip set. However its firmware restricts it to only work with Jaz
drives.

On connecting the cable a message like this appears four times in the log:
 reset full speed USB device number 4 using uhci_hcd

That's non-fatal but the US_FL_SINGLE_LUN quirk fixes it.
Signed-off-by: NMark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Initialize USB PHY after every Link controller reset

Cc: 3.16+ <stable@vger.kernel.org>
Cc: Tim Bird <tbird20d@gmail.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

PHY drivers keep track of the current state of the hardware,
so don't change PHY settings under it.

Cc: 3.16+ <stable@vger.kernel.org>
Cc: Tim Bird <tbird20d@gmail.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

During surprise device hotplug removal tests, it was observed that
hub_events may try to call usb_lock_device on a device that has already
been freed. Protect the usb_device by taking out a reference (under the
hub_event_lock) when hub_events pulls it off the list, returning the
reference after hub_events is finished using it.
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Suggested-by: David Bulkow <david.bulkow@stratus.com> for using kref
Suggested-by: Alan Stern <stern@rowland.harvard.edu> for placement
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are a large numbers of issues with ASM1051 devices in uas mode:

1) They do not support REPORT SUPPORTED OPERATION CODES

2) They use out of spec 8 byte status iu-s when they have no sense data,
   switching to normal 16 byte status iu-s when they do have sense data.

3) They hang / crash when combined with some disks, e.g. a Crucial M500 ssd.

4) They hang / crash when stressed (through e.g. sg_reset --bus) with disks
   with which then normally do work (once 1 & 2 are worked around).

Where as in BOT mode they appear to work fine, so the best way forward with
these devices is to just blacklist them for uas usage.

Unfortunately this is easier said then done. as older versions of the ASM1053
(which works fine) use the same usb-id as the ASM1051.

When connected over USB-3 the 2 can be told apart by the number of streams
they support. So this patch adds some less then pretty code to disable uas for
the ASM1051. When connected over USB-2, simply disable uas alltogether for
devices with the shared usb-id.

Cc: stable@vger.kernel.org # 3.16
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Endpoint 0 should not be disabled, so we start loop counter from number 1.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes kernel panic/interrupt storm/etc issues if bootloader
left s3c-hsotg module in enabled state. Now interrupt handler is enabled
only after proper configuration of hardware registers.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This leads to potential spinlock recursion in composite framework, other
udc drivers also don't call it directly from pullup method.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes possible freeze caused by infinite loop in interrupt
context.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the Generic PHY Framework a NULL phy is considered to be a valid phy
thus the "if (hsotg->phy)" check does not give us the information whether
the Generic PHY Framework is used.

In addition to the above this patch also removes phy_init from probe and
phy_exit from remove. This is not necessary when init/exit is done in the
s3c_hsotg_phy_enable/disable functions.
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the driver is removed s3c_hsotg_phy_disable is called three times
instead of once. This results in decreasing of the phy reference counter
below zero and thus consecutive inserts of the module fails.

This patch removes calls to s3c_hsotg_phy_disable from s3c_hsotg_remove
and s3c_hsotg_udc_stop.

s3c_hsotg_udc_stop is called from udc-core.c only after
usb_gadget_disconnect, which in turn calls s3c_hsotg_pullup, which
already calls s3c_hsotg_phy_disable.

s3c_hsotg_remove must be called only after udc_stop, so there is no
point in disabling phy once again there.
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NTaylor Braun-Jones <taylor.braun-jones@ge.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 71c731a2 (usb: host: xhci: Fix Compliance Mode
on SN65LVP3502CP Hardware) implemented a workaround
for a known issue with Texas Instruments' USB 3.0
redriver IC but it left a condition where any xHCI
host would be taken out of reset if port was placed
in compliance mode and there was no device connected
to the port.

That condition would trigger a fake connection to a
non-existent device so that usbcore would trigger a
warm reset of the port, thus taking the link out of
reset.

This has the side-effect of preventing any xHCI host
connected to a Linux machine from starting and running
the USB 3.0 Electrical Compliance Suite because the
port will mysteriously taken out of compliance mode
and, thus, xHCI won't step through the necessary
compliance patterns for link validation.

This patch fixes the issue by just adding a missing
check for XHCI_COMP_MODE_QUIRK inside
xhci_hub_report_usb3_link_state() when PORT_CAS isn't
set.

This patch should be backported to all kernels containing
commit 71c731a2.

Fixes: 71c731a2 (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware)
Cc: Alexis R. Cortes <alexis.cortes@ti.com>
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add back some PIDs that were mistakingly remove when reverting commit
73228a05 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.

Fixes: 63a901c0 ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: NLei Liu <lei35151@163.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The PHY configuration is stored in an opaque "config" field, but when
allocating the structure, its proper size needs to be known. In the case
of UTMI, the proper structure is tegra_utmip_config of which a local
variable already exists, so we can use that to obtain the size from.

Fixes the following warning from the sparse checker:

	drivers/usb/phy/phy-tegra-usb.c:882:17: warning: expression using sizeof(void)

Fixes: 81d5dfe6 (usb: phy: tegra: Read UTMIP parameters from device tree)
Cc: stable@vger.kernel.org
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add imx6sx support
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Up to now, when endpoint addresses in descriptors were non-consecutive,
there were created redundant files, which could cause problems in kernel,
when user tried to read/write to them. It was result of fact that maximum
endpoint address was taken as total number of endpoints in function.

This patch adds endpoint descriptors counting and storing their addresses
in eps_addrmap to verify their cohesion in each speed.

Endpoint address map would be also useful for further features, just like
vitual endpoint address mapping.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the usb_pkt_pop(). If a gadget driver calls
usb_ep_dequeue(), this driver will call the usb_pkt_pop().
So, the usb_pkt_pop() should cancel the transaction.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the condition of is_done in usbhsf_dma_push_done().
This function will be called after a transmission finished by DMAC.
So, the function should check if the transmission packet is short packet
or not. Also the function should call try_run to send the zero packet
by the pio handler if the "*is_done" is not set. Otherwize, the
transaction will not finish if a gadget driver sets the "zero" flag
in a transmission.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch protects the mod->irq_bempsts and mod->irq_brdysts by
spin lock in the usbhs_status_get_each_irq() because other functions
will write them during spin lock. Otherwise, the driver will clears
the BRDYSTS and/or BEMPSTS wrongly, and then, the transaction will not
finish.
Also since the driver should use the INTSTS0 and BRDYSTS and BEMPSTS
as the same timing, the patch protects them.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some gadget drivers will call usb_ep_queue() more than once before
the first queue doesn't finish. However, this driver didn't handle
it correctly. So, this patch fixes the behavior of some
usbhs_pkt_handle using the "running" flag. Otherwise, the oops below
happens if we use g_ncm driver and when the "iperf -u -c host -b 200M"
is running.

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 80000007 [#1] SMP ARM
Modules linked in: usb_f_ncm g_ncm libcomposite u_ether
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W      3.17.0-rc1-00008-g8b2be8a-dirty #20
task: c051c7e0 ti: c0512000 task.ti: c0512000
PC is at 0x0
LR is at usbhsf_pkt_handler+0xa8/0x114
pc : [<00000000>]    lr : [<c0278fb4>]    psr: 60000193
sp : c0513ce8  ip : c0513c58  fp : c0513d24
r10: 00000001  r9 : 00000193  r8 : eebec4a0
r7 : eebec410  r6 : eebe0c6c  r5 : 00000000  r4 : ee4a2774
r3 : 00000000  r2 : ee251e00  r1 : c0513cf4  r0 : ee4a2774
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Clearly this was meant to be an include guard, but a trailing
underscore was missing. It has been this way since the file was
introduced in 0fe6f1d1 ("usb: udc: add Faraday fusb300 driver").

Fixes: 0fe6f1d1 ("usb: udc: add Faraday fusb300 driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Without this patch, some hosts keep restarting indefinitely the target.

Fixes: ae8e530a (usb: gadget: net2280: Code Cleanup)
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

CPPI TX does not transmit ZLP for TX transfers which
- transfer size is multiple of EP packet size,
- and URB_ZERO_PACKET is set in urb->transfer_flags.

The fix is transmitting the ZLP using PIO mode after the CPPI TX is
done.

Validated using the following usbtest write case in MUSB host mode.

  # testusb -t1 -c1
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This VID:PID is used for some Direct IP devices behaving
identical to the already supported 0F3D:68AA devices.

Cc: <stable@vger.kernel.org>
Reported-by: NLars Melin <larsm17@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Sierra Wireless Direct IP devices using the 68A3 product ID
can be configured for modes including a CDC ECM class function.
The known example uses interface numbers 12 and 13 for the ECM
control and data interfaces respectively, consistent with CDC
MBIM function interface numbering on other Sierra devices.

It seems cleaner to restrict this driver to the ff/ff/ff
vendor specific interfaces rather than increasing the already
long interface number blacklist.  This should be more future
proof if Sierra adds more class functions using interface
numbers not yet in the blacklist.

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add device id for NOVITUS Bono E thermal printer.
Reported-by: NEmanuel Koczwara <poczta@emanuelkoczwara.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add back some PIDs that were mistakingly remove when reverting commit
73228a05 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.

Fixes: 63a901c0 ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: NLei Liu <lei35151@163.com>
Cc: stable <stable@vger.kernel.org>

commit bdd405d2 ("usb: hub: Prevent hub autosuspend if
usbcore.autosuspend is -1") causes a build error if CONFIG_PM_RUNTIME is
disabled.  Fix that by doing a simple #ifdef guard around it.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Michael Welling <mwelling@emacinc.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 03936890.

Vivek writes:
	We not longer need this patch, since we have planned to remove
	the usb-phy drivers for samsung [1], we have completely deleted
	the support for the the same from ohci-exynos and ehci-exynos
	drivers too [2].  Sorry for the confusion, but this patch can be
	dropped and instead we can pick the patches in [2].

	[1] http://www.mail-archive.com/linux-samsung-soc@vger.kernel.org/msg35774.html
	[2] https://www.mail-archive.com/linux-samsung-soc@vger.kernel.org/msg35695.html
	    https://www.mail-archive.com/linux-samsung-soc@vger.kernel.org/msg35696.html

Cc: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a bit bigger hammer then I would like to use for this, but for now
it will have to make do. I'm working on getting my hands on one of these so
that I can try to get streams to work (with a quirk flag if necessary) and
then we can re-enable them.

For now this at least makes uas capable disk enclosures work again by forcing
fallback to the usb-storage driver.

https://bugzilla.kernel.org/show_bug.cgi?id=79511

Cc: stable@vger.kernel.org # 3.15
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to verify the number of ports requested by subdriver to avoid
writing beyond the end of fixed-size array in interface data.

The current usb-serial implementation is limited to eight ports per
interface but failed to verify that the number of ports requested by a
subdriver (which could have been determined from device descriptors) did
not exceed this limit.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to verify the maximum number of endpoints per type to avoid
writing beyond the end of a stack-allocated array.

The current usb-serial implementation is limited to eight ports per
interface but failed to verify that the number of endpoints of a certain
type reported by a device did not exceed this limit.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since we want to keep support for both older usb-phys as well as the
newer generic phys, lets first get the generic PHYs and fallback to
older USB-PHYs only when we fail to get the former.
This should fix the issue with ehci-exynos and ohci-exynos, wherein
in the absence of SAMSUNG_USB2PHY config symbol, we end up getting
the NOP_USB_XCEIV phy when the same is enabled. And thus the PHYs
are not configured properly.
Reported-by: NSachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Jingoo Han <jg1.han@samsung.com>
Tested-by: NSachin Kamat <sachin.kamat@samsung.com>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If user specifies that USB autosuspend must be disabled by module
parameter "usbcore.autosuspend=-1" then we must prevent
autosuspend of USB hub devices as well.

commit 596d789a introduced in v3.8 changed the original behaivour
and stopped respecting the usbcore.autosuspend parameter for hubs.

Fixes: 596d789a "USB: set hub's default autosuspend delay as 0"

Cc: [3.8+] <stable@vger.kernel.org>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Tested-by: NMichael Welling <mwelling@emacinc.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

I have a j5 create (JUA210) USB 2 video device and adding it device id
to SIS USB video gets it to work.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Set the default EP max packet value as 8 bytes, because in the case
of low-speed, 'ep_mps' is not set. Thus, the default value of 'ep_mps'
should be considered for the case of low-speed.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The roothub's index per controller is from 0, but the hub port index per hub
is from 1, this patch fixes "can't find device at roohub" problem for connecting
test fixture at roohub when do USB-IF Embedded Host High-Speed Electrical Test.

This patch is for v3.12+.

Cc: stable@vger.kernel.org
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The uSCSI from Newer Technology is a SCSI-USB converter with USB ID 06ca:2003.
Like several other SCSI-USB products, it's a Shuttle Technology OEM device.
Without a suitable entry in unusual-devs.h, the converter can only access the
(single) device with SCSI ID 0. Copying the entry for device 04e6:0002 allows
it to work with devices with other SCSI IDs too.

There are currently six entries for Shuttle-developed SCSI-USB devices in
unusual-devs.h (grep for euscsi):
  04e6:0002  Shuttle eUSCSI Bridge    USB_SC_DEVICE, USB_PR_DEVICE
  04e6:000b  Shuttle eUSCSI Bridge    USB_SC_SCSI, USB_PR_BULK
  04e6:000c  Shuttle eUSCSI Bridge    USB_SC_SCSI, USB_PR_BULK
  050d:0115  Belkin USB SCSI Adaptor  USB_SC_SCSI, USB_PR_BULK
  07af:0004  Microtech USB-SCSI-DB25  USB_SC_DEVICE, USB_PR_DEVICE
  07af:0005  Microtech USB-SCSI-HD50  USB_SC_DEVICE, USB_PR_DEVICE

lsusb -v output for the uSCSI lists
  bInterfaceSubClass      6 SCSI
  bInterfaceProtocol     80 Bulk (Zip)

This patch adds an entry for the uSCSI to unusual_devs.h.
Signed-off-by: NMark Knibbs <markk@clara.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>