Some cards can generate CCMP IVs in HW, but require the space for the IV
to be pre-allocated in the frame at the correct offset. Add a key flag
that allows us to achieve this.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

genlmsg_end() cannot fail, it just returns the length
of the message. Thus, error handling for it is useless.
While removing it, I also noticed a useless variable
and removed this it as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If there are no cooked monitor interfaces, there's
no point in building the radiotap RX header for the
frame and iterating the interface list.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's an extra pair of parentheses here that
is simply confusing because it implies a nesting
that doesn't actually exist. Just remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 calls ieee80211_set_wmm_default (which in turn
calls drv_conf_tx()) for every new interface, including
"internal" ones (e.g. monitor interface, which the low-level
driver doesn't know about).

Limit this call only to valid interfaces.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When hybrid mode is enabled (accept_ra == 2), the kernel also sees RAs
generated locally. This is useful since it allows the kernel to auto-configure
its own interface addresses.

However, if 'accept_ra_defrtr' and/or 'accept_ra_rtr_pref' are set and the
locally generated RAs announce the default route and/or other route information,
the kernel happily inserts bogus routes with its own address as gateway.

With this patch, adding routes from an RA will be skiped when the RAs source
address matches any local address, just as if 'accept_ra_defrtr' and
'accept_ra_rtr_pref' were set to 0.
Signed-off-by: NAndreas Hofmeister <andi@collax.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dan Siemon would like to add tunnelling support to cls_flow

This preliminary patch introduces use of skb_header_pointer() to help
this task, while avoiding skb head reallocation because of deep packet
inspection.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In func ipv4_dst_check,check_peer_pmtu should be called only when peer is updated.
So,if the peer is not updated in ip_rt_frag_needed,we can not inc __rt_peer_genid.
Signed-off-by: NGao feng <gaofeng@cn.fujitsu.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was enabled by default and the messages guarded
by the define are useful.
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a long standing bug in linux tcp stack, about ACK messages sent
on behalf of TIME_WAIT sockets.

In the IP header of the ACK message, we choose to reflect TOS field of
incoming message, and this might break some setups.

Example of things that were broken :
  - Routing using TOS as a selector
  - Firewalls
  - Trafic classification / shaping

We now remember in timewait structure the inet tos field and use it in
ACK generation, and route lookup.

Notes :
 - We still reflect incoming TOS in RST messages.
 - We could extend MuraliRaja Muniraju patch to report TOS value in
netlink messages for TIME_WAIT sockets.
 - A patch is needed for IPv6
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Renato Westphal noticed that since commit a2835763
"rtnetlink: handle rtnl_link netlink notifications manually" was merged
we no longer send a netlink message when a networking device is moved
from one network namespace to another.

Fix this by adding the missing manual notification in dev_change_net_namespaces.

Since all network devices that are processed by dev_change_net_namspaces are
in the initialized state the complicated tests that guard the manual
rtmsg_ifinfo calls in rollback_registered and register_netdevice are
unnecessary and we can just perform a plain notification.

Cc: stable@kernel.org
Tested-by: NRenato Westphal <renatowestphal@gmail.com>
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is bug in commit 5e2b61f7(ipv4: Remove flowi from struct rtable).
It makes xfrm4_fill_dst() modify wrong data structure.
Signed-off-by: NZheng Yan <zheng.z.yan@intel.com>
Reported-by: NKim Phillips <kim.phillips@freescale.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit f39925db
(ipv4: Cache learned redirect information in inetpeer.)
removed some ICMP packet validations which are required by
RFC 1122, section 3.2.2.2:
...
  A Redirect message SHOULD be silently discarded if the new
  gateway address it specifies is not on the same connected
  (sub-) net through which the Redirect arrived [INTRO:2,
  Appendix A], or if the source of the Redirect is not the
  current first-hop gateway for the specified destination (see
  Section 3.3.1).
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pair of functions,

 * skb_clone_tx_timestamp()
 * skb_complete_tx_timestamp()

were designed to allow timestamping in PHY devices. The first
function, called during the MAC driver's hard_xmit method, identifies
PTP protocol packets, clones them, and gives them to the PHY device
driver. The PHY driver may hold onto the packet and deliver it at a
later time using the second function, which adds the packet to the
socket's error queue.

As pointed out by Johannes, nothing prevents the socket from
disappearing while the cloned packet is sitting in the PHY driver
awaiting a timestamp. This patch fixes the issue by taking a reference
on the socket for each such packet. In addition, the comments
regarding the usage of these function are expanded to highlight the
rule that PHY drivers must use skb_complete_tx_timestamp() to release
the packet, in order to release the socket reference, too.

These functions first appeared in v2.6.36.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Cc: <stable@vger.kernel.org>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now tcp_md5_hash_header() has a const tcphdr argument, we can add more
const attributes to callers.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_md5_hash_header() writes into skb header a temporary zero value,
this might confuse other users of this area.

Since tcphdr is small (20 bytes), copy it in a temporary variable and
make the change in the copy.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMaciej Żenczykowski <maze@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding const qualifiers to pointers can ease code review, and spot some
bugs. It might allow compiler to optimize code further.

For example, is it legal to temporary write a null cksum into tcphdr
in tcp_md5_hash_header() ? I am afraid a sniffer could catch the
temporary null value...
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using the dev->next chain and trying to resync at each call to
dev_seq_start, use the name hash, keeping the bucket and the offset in
seq->private field.

Tests revealed the following results for ifconfig > /dev/null
	* 1000 interfaces:
		* 0.114s without patch
		* 0.089s with patch
	* 3000 interfaces:
		* 0.489s without patch
		* 0.110s with patch
	* 5000 interfaces:
		* 1.363s without patch
		* 0.250s with patch
	* 128000 interfaces (other setup):
		* ~100s without patch
		* ~30s with patch
Signed-off-by: NMihai Maruseac <mmaruseac@ixiacom.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I've split this bit out of the skb frag destructor patch since it helps enforce
the use of the fragment API.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up till now the IP{,V6}_TRANSPARENT socket options (which actually set
the same bit in the socket struct) have required CAP_NET_ADMIN
privileges to set or clear the option.

- we make clearing the bit not require any privileges.
- we allow CAP_NET_ADMIN to set the bit (as before this change)
- we allow CAP_NET_RAW to set this bit, because raw
  sockets already pretty much effectively allow you
  to emulate socket transparency.
Signed-off-by: NMaciej Żenczykowski <maze@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_fin() only needs socket pointer, we can remove skb and th params.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Turull reported inaccuracies in pktgen when using low packet
rates, because we call ndelay(val) with values bigger than 20000.

Instead of calling ndelay() for delays < 100us, we can instead loop
calling ktime_now() only.
Reported-by: NDaniel Turull <daniel.turull@gmail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 356f0398 (TCP: increase default initial receive
window.), we allow sender to send 10 (TCP_DEFAULT_INIT_RCVWND) segments.

Change tcp_fixup_rcvbuf() to reflect this change, even if no real change
is expected, since sysctl_tcp_rmem[1] = 87380 and this value
is bigger than tcp_fixup_rcvbuf() computed rcvmem (~23720)

Note: Since commit 356f0398 limited default window to maximum of
10*1460 and 2*MSS, we use same heuristic in this patch.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems ip_gre is able to change dev->needed_headroom on the fly.

Its is not legal unfortunately and triggers a BUG in raw_sendmsg()

skb = sock_alloc_send_skb(sk, ... + LL_ALLOCATED_SPACE(rt->dst.dev)

< another cpu change dev->needed_headromm (making it bigger)

...
skb_reserve(skb, LL_RESERVED_SPACE(rt->dst.dev));

We end with LL_RESERVED_SPACE() being bigger than LL_ALLOCATED_SPACE()
-> we crash later because skb head is exhausted.

Bug introduced in commit 243aad83 in 2.6.34 (ip_gre: include route
header_len in max_headroom calculation)
Reported-by: NElmar Vonlanthen <evonlanthen@gmail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Timo Teräs <timo.teras@iki.fi>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I audited all of the callers in the tree and only one of them (pktgen) expects
it to do so. Taking this reference is pretty obviously confusing and error
prone.

In particular I looked at the following commits which switched callers of
(__)skb_frag_set_page to the skb paged fragment api:

6a930b9f cxgb3: convert to SKB paged frag API.
5dc3e196 myri10ge: convert to SKB paged frag API.
0e0634d2 vmxnet3: convert to SKB paged frag API.
86ee8130 virtionet: convert to SKB paged frag API.
4a22c4c9 sfc: convert to SKB paged frag API.
18324d69 cassini: convert to SKB paged frag API.
b061b39e benet: convert to SKB paged frag API.
b7b6a688 bnx2: convert to SKB paged frag API.
804cf14e net: xfrm: convert to SKB frag APIs
ea2ab693 net: convert core to skb paged frag APIs
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when use dst_get_neighbour to get neighbour, we need
rcu_read_lock to protect, since dst_get_neighbour uses
rcu_dereference.

The bug was reported by Ari Savolainen <ari.m.savolainen@gmail.com>

[  105.612095]
[  105.612096] ===================================================
[  105.612100] [ INFO: suspicious rcu_dereference_check() usage. ]
[  105.612101] ---------------------------------------------------
[  105.612103] include/net/dst.h:91 invoked rcu_dereference_check()
without protection!
[  105.612105]
[  105.612106] other info that might help us debug this:
[  105.612106]
[  105.612108]
[  105.612108] rcu_scheduler_active = 1, debug_locks = 0
[  105.612110] 1 lock held by dnsmasq/2618:
[  105.612111]  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff815df8c7>]
rtnl_lock+0x17/0x20
[  105.612120]
[  105.612121] stack backtrace:
[  105.612123] Pid: 2618, comm: dnsmasq Not tainted 3.1.0-rc1 #41
[  105.612125] Call Trace:
[  105.612129]  [<ffffffff810ccdcb>] lockdep_rcu_dereference+0xbb/0xc0
[  105.612132]  [<ffffffff815dc5a9>] neigh_update+0x4f9/0x5f0
[  105.612135]  [<ffffffff815da001>] ? neigh_lookup+0xe1/0x220
[  105.612139]  [<ffffffff81639298>] arp_req_set+0xb8/0x230
[  105.612142]  [<ffffffff8163a59f>] arp_ioctl+0x1bf/0x310
[  105.612146]  [<ffffffff810baa40>] ? lock_hrtimer_base.isra.26+0x30/0x60
[  105.612150]  [<ffffffff8163fb75>] inet_ioctl+0x85/0x90
[  105.612154]  [<ffffffff815b5520>] sock_do_ioctl+0x30/0x70
[  105.612157]  [<ffffffff815b55d3>] sock_ioctl+0x73/0x280
[  105.612162]  [<ffffffff811b7698>] do_vfs_ioctl+0x98/0x570
[  105.612165]  [<ffffffff811a5c40>] ? fget_light+0x340/0x3a0
[  105.612168]  [<ffffffff811b7bbf>] sys_ioctl+0x4f/0x80
[  105.612172]  [<ffffffff816fdcab>] system_call_fastpath+0x16/0x1b
Reported-by: NAri Savolainen <ari.m.savolainen@gmail.com>
Signed-off-by: NRongQing <roy.qing.li@gmail.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is just a cleanup.

My testing version of Smatch warns about this:
net/core/filter.c +380 check_load_and_stores(6)
	warn: check 'flen' for negative values

flen comes from the user.  We try to clamp the values here between 1
and BPF_MAXINSNS but the clamp doesn't work because it could be
negative.  This is a bug, but it's not exploitable.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This cleanup patch removes unnecessary include from net/ipv6/ip6_fib.c.
Signed-off-by: NKevin Wilson <wkevils@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipv4: compat_ioctl is local to af_inet.c, make it static
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

we should decrease ops->unresolved_rules when deleting a unresolved rule.
Signed-off-by: NZheng Yan <zheng.z.yan@intel.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a sanity check on the values provided by user space for
the hardware time stamping configuration. If the values lie outside of
the absolute limits, then the ioctl request will be denied.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the rcu_barrier from rollback_registered_many
(inside the rtnl_lock) into netdev_run_todo (just outside the rtnl_lock).
This allows us to gain the full benefit of sychronize_net calling
synchronize_rcu_expedited when the rtnl_lock is held.

The rcu_barrier in rollback_registered_many was originally a synchronize_net
but was promoted to be a rcu_barrier() when it was found that people were
unnecessarily hitting the 250ms wait in netdev_wait_allrefs().  Changing
the rcu_barrier back to a synchronize_net is therefore safe.

Since we only care about waiting for the rcu callbacks before we get
to netdev_wait_allrefs() it is also safe to move the wait into
netdev_run_todo.

This was tested by creating and destroying 1000 tap devices and observing
/proc/lock_stat.  /proc/lock_stat reports this change reduces the hold
times of the rtnl_lock by a factor of 10.  There was no observable
difference in the amount of time it takes to destroy a network device.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initial cwnd being 10 (TCP_INIT_CWND) instead of 3, change
tcp_fixup_sndbuf() to get more than 16384 bytes (sysctl_tcp_wmem[1]) in
initial sk_sndbuf
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_recycle_check resets the skb if it's eligible for recycling.
However, there are times when a driver might want to optionally
manipulate the skb data with the skb before resetting the skb,
but after it has determined eligibility.  We do this by splitting the
eligibility check from the skb reset, creating two inline functions to
accomplish that task.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Acked-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The transparent socket option setting was not copied to the time wait
socket when an inet socket was being replaced by a time wait socket. This
broke the --transparent option of the socket match and may have caused
that FIN packets belonging to sockets in FIN_WAIT2 or TIME_WAIT state
were being dropped by the packet filter.
Signed-off-by: NKOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.

Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling icmpv6_send() on a local message size error leads to
an incorrect update of the path mtu. So use xfrm6_local_rxpmtu()
to notify about the pmtu if the IPV6_DONTFRAG socket option is
set on an udp or raw socket, according RFC 3542 and use
ipv6_local_error() otherwise.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip6_append_data() builds packets based on the mtu from dst_mtu(rt->dst.path).
On IPsec the effective mtu is lower because we need to add the protocol
headers and trailers later when we do the IPsec transformations. So after
the IPsec transformations the packet might be too big, which leads to a
slowpath fragmentation then. This patch fixes this by building the packets
based on the lower IPsec mtu from dst_mtu(&rt->dst) and adapts the exthdr
handling to this.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pointer to mtu_info is taken from the common buffer
of the skb, thus it can't be a NULL pointer. This patch
removes this check on mtu_info.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>