The event mask was specified as 0xF (4 bits) when in reality is 0x1F (5
bits) in order to be capable of representing all FIFO length values from
0 to 16.

This caused a problem: when the keypad reported 16 pending events the
driver took it as 0, and did nothing. This in turn caused the keypad to
re-issue the interrupt over and over again.
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The pull mask is created by looping each row (column) and building an
8-bit integer with the configuration. It is written byte-by-byte, when
we reach the end of the rows (columns) or we're at the 3rd line (which
finishes the first byte, since each pin is 2bits on the mask).

However, this only works if we have at most 8 pins (2 bytes), which is
not the case for the ADP5589. So, write the byte at each boundary (every
4 rows/columns).
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

My Pengutronix address is not valid anymore, redirect people to the
Pengutronix kernel team.
Reported-by: NHarald Geyer <harald@ccbib.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NRobert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The suspend scan rate value should not exceed 1000, unfortunately when
implementing the limit we used max_t instead of min_t, causing the value to
be at least 1000.
Signed-off-by: NDudley Du <dudl@cypress.com>
Reviewed-by: NBenson Leung <bleung@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

According to Elan's firmware engineers we should not be subtracting 1 form
the raw number of x and y traces so that the pitch size is correct. For
example, if the touchpad x resolution is 2800 and x trace number is 20,
the pitch size of x should be 2800/20 = 140, not 2800/19 = 147.36.
Signed-off-by: NDuson Lin <dusonlin@emc.com.tw>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When hover is detected report ABS_MT_DISTANCE as 1; for active contacts
the distance is reported as 0.
Signed-off-by: NDuson Lin <dusonlin@emc.com.tw>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Let's zero-extend hardware id number when forming firmware file name,
to avoid kernel requesting firmware like "elants_i2c_   0.bin", which
is quite unexpected.

Acked-by: Charlie Mooney<charliemooney@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This change allows atmel_mxt_ts to bind to ACPI-enumerated devices in
Google Pixel 2 (2015).

While newer version of ACPI standard allow use of device-tree-like
properties in device descriptions, the version of ACPI implemented in
Google BIOS does not support them, and we have to resort to DMI data to
specify exact characteristics of the devices (touchpad vs. touchscreen,
GPIO to button mapping, etc).

Pixel 1 continues to use i2c devices and platform data created by
chromeos-laptop driver, since ACPI does not enumerate them.
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This adds rumble support for Xbox One controller by sending continuous
rumble command. Trigger button rumbling is not yet implemented.
Signed-off-by: NMing-ting Yao Wei <mwei@lxde.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Replace old pr_* with dev_* debugging macros
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

VMMouse enables low-latency mouse-cursor-movements for VMWare and QEMU
guests.  By removing the guest cursor and using the host as a guest cursor
the cursor movement appears instant although in reality there is some lag.
To be able to do this, the host's view of the cursor position must exactly
match the guest's view and an absolute pointer device is needed. Enter the
VMMouse. While the VMMouse driver has historically been an Xorg user-space
driver, implementing it as a kernel imput driver enables rootless Xorg and
new compositing display servers for VMware guests.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Get pressure format flag from firmware to check if we need to normalize
pressure data before reporting it.
Signed-off-by: NDuson Lin <dusonlin@emc.com.tw>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

To save people some time let's document that we do not want new quirks for
"force-release" keys in the kernel and that they should patch userspace
(udev) instead.
Suggested-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NMasaki Ota <masaki.ota@jp.alps.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This change adds support for SS4 touchpad devices as ALPS_PROTO_V8
protocol.  They are real multi-touch devices and can be found in TOSHIBA
Tecra C50.
Signed-off-by: NMasaki Ota <masaki.ota@jp.alps.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

In preparation for adding support for SS4 touchpads, let's split
alps_set_abs_params_mt into common, v7-specific, and other protocols
portions.
Signed-off-by: NMasaki Ota <masaki.ota@jp.alps.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Commit 1daa4303 ("net/mlx4_core: Deprecate error message at
ConnectX-2 cards startup to debug") did the deprecation only for port 1
of the card. Need to deprecate for port 2 as well.

Fixes: 1daa4303 ("net/mlx4_core: Deprecate error message at ConnectX-2 cards startup to debug")
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the "linux,gpio-keymap" DT property is defined, the T19 keys are
configured and the device is setup as a touchpad rather than a touchscreen.
The logic is part of the input device initialization routine but it can be
factored out to its own function to simplify the former.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for the new T100 object which replaces the previous T9
multitouch touchscreen object in recent maXTouch devices. T100 provides
improved reporting with selectable auxiliary information, and a type field
for hover/stylus/glove reporting.

The hovering finger support was based on Chung-Yih's work in the ChromiumOS
downstream kernel:

https://chromium-review.googlesource.com/#/c/219280/Signed-off-by: NNick Dyer <nick.dyer@itdev.co.uk>
Acked-by: NYufeng Shen <miletus@chromium.org>
[javier: Factor out T9 and T100 init functions and rework hover support]
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

mvneta_adjust_link() is a callback for of_phy_connect() and should
not be called directly. The result of calling it directly is as below:
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the comment right before explains, the keyboard state is to be cleared
only if the EC wasn't a wakeup source in the last suspend.

Without this commit, there's an unneeded delay when resuming from suspend
and we also lose the key that was pressed while suspended.
Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This driver does not use any PCI IDs, don't include the pci_ids.h header.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When slowly dropping 1, 2 and then 3 fingers on an image sensor touchpad,
we can see that the first finger gets reassigned a new slot while it did
not move. This is due to the kernel tracking algorithm which can not assign
correctly the 3 touches, being out of slots.

Declaring that we support 3 slots allows to actually forward:
slot 0 -> down, slot 1 -> up, slot 2 -> down
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: Henrik Rydberg <rydberg@bitmath.org
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This reverts commit 09d042a2 ("Revert "Input: synaptics - use dmax in
input_mt_assign_slots"")

Now that balanced slots assignments seem to be fixed, let's re-enable the
use in synaptics.c and wait for users to complain if there are still
problems.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: Henrik Rydberg <rydberg@bitmath.org
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The recent inclusion of a deassignment cost in the slot assignment
algorithm did not properly account for the corner cases where the
solutions are overcovered. This change makes sure the resulting
assignment is unique, allocating new slots when necessary.
Signed-off-by: NHenrik Rydberg <rydberg@bitmath.org>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

On V2 devices the DualPoint Stick reports bare packets, these should be
reported via the "AlpsPS/2 ALPS DualPoint Stick" dev2 evdev node, which also
has the INPUT_PROP_POINTING_STICK propbit set.

Note that since there is no way to distinguish these packets from an external
PS/2 mouse (insofar as these laptops have an external PS/2 port) this means
that we will be reporting PS/2 mouse events via this evdev node too, as we've
been doing in kernel 3.19 and older.

This has been tested on a Dell Latitude D620 and a Dell Latitude E6400,
which both have a V2 touchpad + a DualPoint Stick which reports bare packets.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Bare packets should be reported via the same evdev device independent on
whether they are detected on the beginning of a packet or in the middle
of a packet.

This has been tested on a Dell Latitude E6400, where the DualPoint Stick
reports bare packets, which get reported via dev3 when the touchpad is
idle, and via dev2 when the touchpad and stick are used simultaneously.

This commit fixes this inconsistency by always reporting bare packets via
dev3. Note that since the come from a DualPoint Stick they really should be
reported via dev2, this gets fixed in a later commit.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

All systems using the TC3589x multifunction expander uses
devicetree, so don't clutter the place with a lot of
and assume it is there.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This driver can only get its platform data from the device tree, and all
platforms using it do that. Localize the platform data for the keypad. A
later patch will enforce the device tree / OF dependence.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

xen-netfront limits transmitted skbs to be at most 44 segments in size. However,
GSO permits up to 65536 bytes, which means a maximum of 45 segments of 1448
bytes each. This slight reduction in the size of packets means a slight loss in
efficiency.

Since c/s 9ecd1a75, xen-netfront sets gso_max_size to
    XEN_NETIF_MAX_TX_SIZE - MAX_TCP_HEADER,
where XEN_NETIF_MAX_TX_SIZE is 65535 bytes.

The calculation used by tcp_tso_autosize (and also tcp_xmit_size_goal since c/s
6c09fa09) in determining when to split an skb into two is
    sk->sk_gso_max_size - 1 - MAX_TCP_HEADER.

So the maximum permitted size of an skb is calculated to be
    (XEN_NETIF_MAX_TX_SIZE - MAX_TCP_HEADER) - 1 - MAX_TCP_HEADER.

Intuitively, this looks like the wrong formula -- we don't need two TCP headers.
Instead, there is no need to deviate from the default gso_max_size of 65536 as
this already accommodates the size of the header.

Currently, the largest skb transmitted by netfront is 63712 bytes (44 segments
of 1448 bytes each), as observed via tcpdump. This patch makes netfront send
skbs of up to 65160 bytes (45 segments of 1448 bytes each).

Similarly, the maximum allowable mtu does not need to subtract MAX_TCP_HEADER as
it relates to the size of the whole packet, including the header.

Fixes: 9ecd1a75 ("xen-netfront: reduce gso_max_size to account for max TCP header")
Signed-off-by: NJonathan Davies <jonathan.davies@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Properly verify that the resulting page aligned end address is larger
than both the start address and the length of the memory area requested.

Both the start and length arguments for ib_umem_get are controlled by
the user. A misbehaving user can provide values which will cause an
integer overflow when calculating the page aligned end address.

This overflow can cause also miscalculation of the number of pages
mapped, and additional logic issues.

Addresses: CVE-2014-8159
Cc: <stable@vger.kernel.org>
Signed-off-by: NShachar Raindel <raindel@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

We need to wait for all fences, not just the exclusive one.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We somehow try to free the SG table twice.

Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=89734Signed-off-by: NChristian König <christian.koenig@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When performing a modeset, use the framebuffer pitch value to set FIMD
IMG_SIZE and Mixer SPAN registers. These are both defined as pitch - the
distance between contiguous lines (bytes for FIMD, pixels for mixer).

Fixes display on Snow (1366x768).
Signed-off-by: NDaniel Stone <daniels@collabora.com>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The legcy colorkey ioctls are only implemented for sprite planes, so
reject the ioctl for primary/cursor planes. If we want to support
colorkeying with these planes (assuming we have hw support of course)
we should just move ahead with the colorkey property conversion.

Testcase: kms_legacy_colorkey
Cc: Tommi Rantala <tt.rantala@gmail.com>
Cc: stable@vger.kernel.org
Reference: http://mid.gmane.org/CA+ydwtr+bCo7LJ44JFmUkVRx144UDFgOS+aJTfK6KHtvBDVuAw@mail.gmail.comReported-and-tested-by: NTommi Rantala <tt.rantala@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Add new Common Code routines to retrieve Firmware Device Log
parameters from PCIE_FW_PF[7]. The firmware initializes its Device Log very
early on and stores the parameters for its location/size in that register.
Using the parameters from the register allows us to access the Firmware
Device Log even when the firmware crashes very early on or we're not
attached to the firmware

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds new macro and few macro changes for fw version 1.13.32.0 also
changes version string in driver to match 1.13.32.0
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 8e709469 ("lguest: add a dummy PCI host bridge.")
lguest uses PCI, but it needs you to frob the ports directly.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Acked-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.

Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.

This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>