Add LCDC pin definitions.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>

Define the HLCDC (HLCD Controller) IP available on some sama5d3 SoCs
(i.e. sama5d31, sama5d33, sama5d34 and sama5d36) in sama5d3 dtsi file.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: NAnthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Define alternative pin muxing for the LCDC pins.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: NAnthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The HLCDC (HLCD Controller) IP supports 4 different output mode (RGB444,
RGB565, RGB666 and RGB888) and the pin muxing will depend on the chosen
RGB mode.

Split pin definitions to be able to set pin config according to the
selected mode.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: NAnthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable RTC for all the at91sam9x5 CPU Modules: this will enable it for all the
EK boards.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add ISI dt node and pinctrl settings in sama5d4.dtsi.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
[nicolas.ferre@atmel.com: sort nodes in order. remove useless comments]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NLeilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable audio support for sama5d4ek board.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add wm8904 codec node and enable it.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable SSC0 node, which will be used for audio.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add SSC 0 and 1 nodes.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add i2c0 aka twi0 on sama5d4 xplained board.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add at91 sama5d4 xplained board support.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

macb0 DT node can have phy child nodes, so add the #{address,
size}_cells for macb0 node.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add the leds DT node in the dts file.
In the leds, d10 is set as heartbeat led.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add alias, node declaration and pinctrl for i2c1 (aka: twi1).
Signed-off-by: NPhilip Attfield <phil.attfield@seqlabs.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Gpio-keys nodes are not using the "reg" property in their sub nodes.
So, there is no need to define #address-cells and #size-cells properties
in gpio-keys nodes: we remove them in these new boards.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

File name had at91 prefix, which is not the case anymore for SAMA5D3.
AT91SAM9x5 was mentioned instead of SAMA5D3 SoC.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable usb device port on at91sam9n12ek board.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add usb device node for at91sam9n12.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable ISI and ov2640 for at91sam9g25ek board.
Meantime, we need to disable the mmc1 and spi0 as they have pin conflict
with ISI.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add the camera sensor ov2640 dt support. And connect sensor to isi node
as well.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add a new file: at91sam9x5_isi.dtsi, which includes ISI node and
pinctrls.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Since turning on idle-halt in commit fe46aa67 (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: NMichel Marti <mma@objectxp.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

There is now only one defconfig for the at91rm9200 and at91sam9. Add ethernet
support for the at91rm9200.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Recent distributions and userspace tools after 2009/2010 depend on
the existence of /sys/class/block/, and will not work with this option enabled.
Signed-off-by: NAnthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Corrected pins used by usart3.
Signed-off-by: NJonas Andersson <jonas@microbit.se>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Commit ff04660e48b20 ("ARM: at91/dt: add SRAM nodes") used the same base
address for sram0 and sram1 leading to the following warning:
WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x50/0x70()
sysfs: cannot create duplicate filename '/devices/platform/300000.sram'
Fix the base address for sram1.
Signed-off-by: NAlexander Stein <alexanders83@web.de>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

On some platforms, there are multiple SRAM nodes defined in the device tree but
some of them are disabled, leading to allocation failure. Try to find the first
enabled SRAM node and allocate from it.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

at91rm9200 standby and suspend to ram has been broken since
00482a40. It is wrongly using AT91_BASE_SYS which is a physical address
and actually doesn't correspond to any register on at91rm9200.

Use the correct at91_ramc_base[0] instead.

Fixes: 00482a40 (ARM: at91: implement the standby function for pm/cpuidle)
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The DDRSDR controller fails miserably to put LPDDR1 memories in
self-refresh. Force the controller to think it has DDR2 memories
during the self-refresh period, as the DDR2 self-refresh spec is
equivalent to LPDDR1, and is correctly implemented in the
controller.

Assume that the second controller has the same fault, but that is
untested.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Removed timeout on XTAL, PLL lock and Master Clock Ready, hang if
something went wrong instead of continuing in unknown condition. There
is not much we can do if a PLL lock never ends, we are running in SRAM
and we will not be able to connect back the sdram or ddram in order to
be able to fire up a message or just panic.

As a bonus, not decounting the timeout register in slow clock mode
reduce cumulated suspend time and resume time from ~17ms to ~15ms.
Signed-off-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: NWenyou.Yang <wenyou.yang@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

There doesn't seem to be any valid reason to allocate the pages array
with the same flags as the buffer itself. Doing so can eventually lead
to the following safeguard in mm/slab.c's cache_grow() to be hit:

        if (unlikely(flags & GFP_SLAB_BUG_MASK)) {
                pr_emerg("gfp: %un", flags & GFP_SLAB_BUG_MASK);
                BUG();
        }

This happens when buffers are allocated with __GFP_DMA32 or
__GFP_HIGHMEM.

Fix this by allocating the pages array with GFP_KERNEL to follow what is
done elsewhere in this file. Using GFP_KERNEL in __iommu_alloc_buffer()
is safe because atomic allocations are handled by __iommu_alloc_atomic().
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. So mark the
non-const structs in arch/arm as const, too.

While at it also add some __initconst annotations.
Acked-by: NJason Cooper <jason@lakedameon.net>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>