Change to use new netdev_alloc_skb interface for 2.6.18.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some more Marvell device id's, these are from the latest SysKonnect
vendor driver version of sk98lin (8.36).
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Improve the firmware selection by adding 2 cases where we should use the
optimized firmware:
* when the actual PCIe link width is lower than 8x.
* when the board is plugged to one of the new Intel PCIe chipsets that
  are known to provide aligned PCIe completions.

The patch actually raises two concerns:
* We might want to add a generic PCI function to get the PCIe link width since
  some other drivers (at least ipath) do the same. But we probably do not want
  to add a new function for every PCIe capability. I will probably look at it
  and discuss it on linux-pci in the future.
* As requested during the submission, the PCI ids of chipsets that are known to
  provided aligned completion are defined in the myri10ge code. If we keep adding
  new ones, it might become better to move them to pciids.h.
  But, this sort of quirk to detect these chipsets are very specific to our NIC,
  I don't think it is worth moving it to the PCI core until somebody else really
  needs it.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update the firmware download URL in Kconfig to match the header
in drivers/net/myri10ge/myri10ge.c.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch decouples the dependency between the rx checksum feature and
vlan feature. This is done by ignoring the checksum information if the
user has disabled rx checksum when vlan is enabled.
Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch addresses an errata found on certain marvell phys concerning
the reset of the BMCR phy register during phy reset.
Signed-Off-By: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Same change as e1000: remove skb->dev assignment, it's now done
by netdev_alloc_skb.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Adds PCI Error recovery callbacks to the Intel 10-gigabit ethernet ixgb
device driver.  Lightly tested, works.

"Zhang, Yanmin" <yanmin_zhang@linux.intel.com> wrote:

Both pci_disable_device and ixgb_down would access the device.  It doesn't
follow Documentation/pci-error-recovery.txt that error_detected shouldn't do
any access to the device.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Recalculate when to wake the queue using DESC_NEEDED instead of a
static hardcoded number.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Increment the version of e100 to 3.5.16-k2, increment dates.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

A recent patch in -mm3 titled
"gregkh-pci-pci-don-t-enable-device-if-already-enabled.patch" causes
pci_enable_device() to be a no-op if the kernel thinks that the device is
already enabled.  This change breaks the PCI error recovery mechanism in
the e100 device driver, since, after PCI slot reset, the card is no longer
enabled.  This is a trivial fix for this problem.  Tested.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

Device 0x10a4 is a double 82571 on a single PCI-Express card and
has 4 gigabit capable ports.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

WoL is constantly giving problems and needed a rewrite. Consolidates
all WoL capabilities into a single function, and disables WoL for all
other ports on the device except for port A.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>

The current probe table causes ledma and lebuffer
"le" devices to get probed twice which is not what
we want.

Match just "le" and look directly at the parent to get the correct
top-level node information.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Found by inspection. The STRIP driver does neigh_lookup() but never
releases.  This driver shouldn't being doing gratuitous arp anyway.

Untested, obviously, because of lack of hardware.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several people run into the situation where the E100
EEPROM contents are fine, but the checksum hasn't been
set properly.  This renders the device useless for
them even though it would function correctly.

The default is off, which retains the current behavior.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increase version.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The user level irq balance daemon uses "eth" as a way to distinquish
ethernet devices. Also, by using device name it is possible to distinquish
different boards.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

To avoid problems with buggy protocols that assume extra header space,
use dev_alloc_skb() when allocating receive buffers.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

At the end of a critical section, we need to force the PCI write
to complete by doing a read.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The code for suspend/resume needs several fixes. The hardware lock
should be setup in probe only, not in resume. Interrupts should be
disabled during suspend, etc.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Change version number for this bundle.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sure that PCI write occurs before the delay.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

To save power, don't enable power to the PHY until device is brought up.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Since many packets have the same checksum starting offset and insertion
location; the driver can save the last information and only tell hardware
when it changes.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The MSS in the transmit engine only has to change if TSO mtu changes. This
means less commands to the chip when mixing TSO and regular data.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The test for MSI IRQ could have timing issues. The PCI write needs to be
pushed out before waiting, and the wait queue should be initialized before
the IRQ.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Don't use force status bit. It was never implemented on all chips, or has
no impact.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use netdev_alloc_skb for buffer allocation to allow for headroom.
This prevents bugs in code paths that assume extra space at the
front and makes sky2 behave like other drivers.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The code to handle cloned skb overwriting is unnecessary in the
sky2 driver and is buggy. The bug is that pskb_expand_head can change the
skb but the driver has already mapped in the header.

Since the sky2 hardware doesn't need to overwrite memory, the buggy
code can just be removed; it was mistakenly copied from the tg3
driver.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>