Use the actual value (0xA5) for the AT91_SHDW_KEY and AT91_WDT_KEY
register fields instead of a bitmask.

This is consistent with how AT91_RSTC_KEY is defined, and is easier to
use in code.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The default value passed through to pxa_gpio_mode() is lost
due to a missing GPIO_DFLT_HIGH mask for nonzero values.  The enclosed
patch fixes this programming error.
Signed-off-by: NBill Gatliff <bgat@billgatliff.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We are currently using the ARMv6 operations but need to duplicate some
of the code because of the introduction of the new CPU barrier
instructions in ARMv7.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The S3C2412 has an reset-errata where the clock
may cause a glitch switching back to EXTCLK. We
force a switch to EXTCLK before writing the
reset register to force use of the CLKCON sync
logic to properly switch.

Fix problem reported by Matthieu Castet.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use the newly introduced __used attribute in place of the deprecated
__attribute_used__.  Functionally the same.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the ioctls and values needed for this to the ARM26/ARM32 ports.  The
actual code has been in the base kernel for a while and automatically turns
on when a port sets the required defines.

[RMK: also added termbits.h changes to avoid build breakage]
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This trivial patch updates the nslu2 and nas-100d headers to
remove pointless GPIO defines, and updates nslu2-setup.c
accordingly. In addition minor style cleanups to some comments
are included.
Signed-off-by: NMichael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch is required as the frequency fixup in nslu2_init does not
run sufficiently early in the boot sequence to take effect. In addition
the dsmg600 setup code behaviour has been improved such that a
'fixup' routine is avoided.
Signed-off-by: NMichael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add physical address of HSMMC to include/asm-arm/arch-s3c2410/map.h
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add definitions for S3C2443 functions in GPIOJ
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.

This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
   getting them indirectly

Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
   they don't need sched.h
b) sched.h stops being dependency for significant number of files:
   on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
   after patch it's only 3744 (-8.3%).

Cross-compile tested on

	all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
	alpha alpha-up
	arm
	i386 i386-up i386-defconfig i386-allnoconfig
	ia64 ia64-up
	m68k
	mips
	parisc parisc-up
	powerpc powerpc-up
	s390 s390-up
	sparc sparc-up
	sparc64 sparc64-up
	um-x86_64
	x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig

as well as my two usual configs.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Trivial unbalanced parenthesis macro fix.
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add definition for high-speed MMC/SD device and add to SMDK2443
device list.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Change the name of the S3C2443_SDI1 to S3C2443_HSMMC to ensure
that it is correctly identified.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We don't need valid_phys_addr_range() or valid_mmap_phys_addr_range()
for the !CONFIG_MMU case.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Presently, we check for the minimum ARM architecture that we're
building for to determine whether we need ASID support.  This is
wrong - if we're going to support a range of CPUs which include
ARMv6 or higher, we need the ASID.

Convert the checks to use a new configuration symbol, and arrange
for ARMv6 and higher CPU entries to select it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add utimensat, signalfd, timerfd, eventfd syscalls.  Add ignore
defines for sync_file_range and fadvise64_64 which we implement
differently.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Change the SPI Channel 1 register offset in s3c_spi1_resource[], and
s3c2412_dma_mappings[]. Offset has to be 0x100 in s3c2412/13's case.
Also, total SPI memory resource size changed to 0x24 for s3c2412/13.
Signed-off-by: NSandeep Patil <psandeep.s@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Integrator/CP SMP platform support was never fully merged, and now
it's causing build breakage.  Remove it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use the new get_irqnr_preamble macro to move the address of the IRQ
controller outside the IRQ handling loop.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add core support for the Kendin/Micrel KS8695 processor family.

It is an ARM922-T based SoC with integrated USART, 4-port Ethernet
Switch, WAN Ethernet port, and optional PCI Host bridge, etc.
 http://www.micrel.com/page.do?page=product-info/sys_on_chip.jsp

This patch is based on earlier patches from Lennert Buytenhek, Ben
Dooks and Greg Ungerer posted to the arm-linux-kernel mailing list in
March 2006;  and Micrel's 2.6.9 port.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Define SZ_512, SZ_256 and SZ_16 in asm-arm/sizes.h.
Remove the definitions from the at91*_devices.c files.

(Dependent on ARM patch #4370/2)
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for Atmel's new AT91SAM9RL range of processors.
Includes similar peripherals as other AT91SAM9 processors, but with a
High-speed USB controller and various sizes of internal SRAM.
Signed-off-by: NNicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Enable devices to signal interrupts via PCI memory cycles.

rev6:
* fix enable/disable typo, Michael Ellerman

rev5:
* fix up ack, enable, and disable for iop13xx_msi_chip

rev4:
* move smp compile fix to separate patch
* use dynamic_irq_init in create_irq()
* hookup mask/unmask routines in iop13xx_msi_chip

rev3:
* change msi.c to use linux/smp.h instead of asm/smp.h
* call dynamic_irq_cleanup at destroy_irq time

rev2:
* destroy_irq did not take the full 128 bits of msi_irq_in_use into account
* added missing '&' for calls to test_and_set_bit and clear_bit

[ebiederm@xmission.com: review comments/suggestions]
[dan.j.williams@intel.com: cleanups/forward port to 2.6-git]
Signed-off-by: NDaniel Wolstenholme <daniel.e.wolstenholme@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Acked-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add base kernel support for the TI DaVinci platform.

This patch only includes interrupts, timers, CPU identification,
serial support and basic power and sleep controller init.  More
drivers to come.
Signed-off-by: NKevin Hilman <khilman@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Resolve the circular dependency in the AT91 header files (io.h and
hardware.h) by moving the at91_sys_read() and at91_sys_write() functions
to io.h
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

arch/arm/plat-iop/io.c:26: error: conflicting types for '__iop3xx_ioremap'
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This adds the ac97 clock to the s3c2443 machine files. It seems to
have been simply missed out previously.
Signed-off-by: NGraeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add devres ecardm_iomap() and ecardm_iounmap() for Acorn expansion
cards.  Convert all expansion card drivers to use them.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than having every driver fiddle about setting its private
IRQ operations and data, provide a helper function to contain
this functionality in one place.

Arrange to remove the driver-private IRQ operations and data when
the device is removed from the driver, and remove the driver
private code to do this.

This fixes potential problems caused by drivers forgetting to
remove these hooks.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

These files are almost all the same.

This patch could be made even simpler if we don't mind POLLREMOVE turning
up in a few architectures that didn't have it previously (which should be
OK as POLLREMOVE is not used anywhere in the current tree).
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add some OMAP 24xx pin mux declarations to support:

 - TUSB 6010 EVM (on H4)
 - All three full speed USB ports
 - GPIOs used with USB0 on Apollon and H4

For OMAP2, issue MUX_WARNINGS and debug messages correctly; and make the
message look more like the OMAP1 message.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Several drivers shared between AT91 and AVR32 chips use cpu_is_xxx()
to handle CPU-specific differences. Currently, such code needs to be
inside #ifdef CONFIG_ARCH_AT91 because the macros don't exist on AVR32.

By defining the same macros on both AT91 and AVR32, these #ifdefs can
be eliminated. Since the macros will evaluate to a constant value for
CPUs that aren't supported by the current architecture, any code that
is only needed on AT91 will be optimized away on AVR32 and vice versa.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- in addition to fixed FB regions - as passed by the bootloader -
  allow dynamic allocations
- do some more checking against overlapping / reserved regions
- move the FB specific parts out from sram.c to fb.c
Signed-off-by: NImre Deak <imre.deak@solidboot.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch syncs framebuffer headers with N800 tree.
Signed-off-by: NKai Svahn <kai.svahn@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix gpmc header
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds a generic mailbox interface for for DSP and IVA
(Image Video Accelerator). This patch itself doesn't contain
any IVA driver.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

ARMv7 can have VIPT, PIPT or ASID-tagged VIVT I-cache. This patch
adds the necessary invalidation of the I-cache when the ASID numbers
are re-used.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Convert the "include" subdirectory to UTF-8.
Signed-off-by: NJohn Anthony Kazos Jr. <jakj@j-a-k-j.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: NUwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>