RT5670 doesn't support auto incrementing writes so driver should
set the use_single_rw flag for regmap.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

This patch adds support for rt288 codec.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add codec driver for the Maxim MAX98357A DAC.
Signed-off-by: NKenneth Westfield <kwestfie@codeaurora.org>
Acked-by: NBanajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

The patch add the customize setting for Dell Dino project.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

We assign rt286->codec in rt286_probe. If rt286_jack_detect is
invoked before rt286_probe, rt286->codec will be NULL and cause
a kernel panic.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch defines an API to select the clock source for specified filters.
Signed-off-by: NFang, Yang A <yang.a.fang@intel.com>
Acked-by: NKevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

this patch fixes following sparse warning:
ts3a227e.c:222:5: warning: symbol 'ts3a227e_enable_jack_detect' was not declared. Should it be static?
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The intercon_extra_3104 is obviously for tlv320aic3104.
Reported-by: NBenoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

To quote from section 1.3.1 of the data sheet:
	The SGTL5000 has an internal reset that is deasserted
	8 SYS_MCLK cycles after all power rails have been brought
	up. After this time, communication can start

	...
	1.0us represents 8 SYS_MCLK cycles at the minimum 8.0 MHz SYS_MCLK.
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

Disables GPIO support and LINE2 input and renames Mic3 input to Mic2,
if tlv320aic3104 mode is seleced. Devicetree binding document is
updated accordingly.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Shift the I2S mode value by the necessary amount before writing the
registers. This makes Right Justified and PCM mode work in addition to
the default Left Justified mode.
Signed-off-by: NFilip Brozovic <fbrozovic@gmail.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Fix the issue introduced by:
36849409 ASoC: tlv320aic3x: Add TDM support

The CTRLC register were not receiving the correct delay configuration,
which will corrupt DSP_A audio mode.

Fixes: 36849409 (ASoC: tlv320aic3x: Add TDM support)
Reported-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

This was overlooked in the late change to remove the I2S padding bits
from S24_LE mode. The patch also limits S32_LE mode to 384kHz, the
maximum according to the datasheets.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

The rt5677 codec has gained code that requires SPI to work correctly,
but there is no provision in Kconfig to prevent the driver from
being used when SPI is disabled or a loadable module, resulting
in this build error:

sound/built-in.o: In function `rt5677_spi_write':
:(.text+0xa7ba0): undefined reference to `spi_sync'
sound/built-in.o: In function `rt5677_spi_driver_init':
:(.init.text+0x253c): undefined reference to `spi_register_driver'

ERROR: "spi_sync" [sound/soc/codecs/snd-soc-rt5677-spi.ko] undefined!
ERROR: "spi_register_driver" [sound/soc/codecs/snd-soc-rt5677-spi.ko] undefined!

This makes the SPI portion of the driver depend on the SPI subsystem,
and disables the function that uses SPI for firmware download if SPI
is disabled. The latter may not be the correct solution, but I could
not come up with a better one.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: af48f1d0 ("ASoC: rt5677: Support DSP function for VAD application")
Signed-off-by: NMark Brown <broonie@kernel.org>

The WM8904 and WM8918 has the same data type, while the WM8912
has different data type. So, use the data in dt ids table to
distinguish them.
Signed-off-by: NAlexander Morozov <linux@meltdown.ru>
[voice.shen@atmel.com: add code to distinguish device type]
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

The PLL introduces jitter, which in turn introduces noice if used
to clock the DAC. Thus, avoid the PLL output, and use the PLL input
to drive the DAC clock, if possible.

This is described for the PCM5142/PCM5242 chips in the answers to the
forum post "PCM5142/PCM5242 DAC clock source" at the TI E2E community
pages (1).

(1) http://e2e.ti.com/support/data_converters/audio_converters/f/64/t/389994Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

Using the PLL in master mode requires using an external connection
between one of the GPIO pins (configured as PLL/4 output) and the
SCK pin. It also requires the external clock to be fed to some other
GPIO pin instead of the SCK pin.

This is described for the PCM5122 chip in the answers to the forum post
"PCM5122 DAC as I2S master troubles with PLL mode" at the TI E2E
community pages (1). The clocking functionality is also much better
described in the datasheet for the chip PCM5242, which seems to be
register compatible with PCM512x and PCM514x (which both have severely
lacking datasheets).

(1) http://e2e.ti.com/support/data_converters/audio_converters/f/64/t/267830Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

Use register field names from the seemingly compatible PCM5242 datasheet,
as the PCM512x and PCM514x datasheets are severly lacking.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds support for rt5650 codec.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The voltage controls key press threshold.
Signed-off-by: NAnatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

ts3a227e datasheet says typical key resistance is
  key1 50 Ohm
  key2 135 Ohm
  key3 240 Ohm
  key4 470 Ohm

The android headset specification expect buttons impedance:
  A (MEDIA) 0-70 Ohm
  D (VOICECOMMAND) 110-180 Ohm
  B (VOLUMEUP) 210-290 Ohm
  C (VOLUMEDOWN) 360-680 Ohm

Thus key mapping should be
  key1 - MEDIA
  key2 - VOICECOMMAND
  key3 - VOLUMEUP
  key3 - VOLUMEDOWN
Signed-off-by: NAnatol Pomozov <anatol.pomozov@gmail.com>
Acked-by: NDylan Reid <dgreid@chromium.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

The I2C init path forgot to init the mutex, leading to an oops when
controls are accessed.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

Save a bit of scheduling by coalescing all the output power up delays
into a single delay.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Give the output disable sequence a chance to fully complete, otherwise
there is a danger we may remove the clock before it is finished
resulting in a pop noise. The delay for each output must be cumulative
and these are coalesced into a single delay.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NThomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

- Add description for the driver
- Add dependency on the I2C module
Signed-off-by: NThomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NThomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

make the sta32x driver usable with device tree configs.  Code is heavily based
on the sta350 driver.
Signed-off-by: NThomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NThomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NThomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

The reset GPIO on the STA32X Codecs is used to reset the Codec and clear
all registers. Also taking it down puts the IC in power save mode, so
we put the device in reset mode when we go to sleep.
Signed-off-by: NThomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

use the regmap API directly rather than relying on the snd_soc_read/write
functions as this seems to be in accordance with common practice.
Signed-off-by: NThomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

The IDE bit in the CONFF register is the third bit not the fourth.
Signed-off-by: NThomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Asus T100TAF uses ACPI ID "10EC5642" for its audio codec. I suppose it is
updated ACPI ID for the RT5642 codec since some earlier platforms are using
"10EC5640" with the RT5642 too.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The purpose of rt286_adc_event is to mute/numnte the ADC mixer.
However, it will also set the capture volume to default value.
As a result, "ADC0 Capture Volume" is not working if it is set
before capture start. This patch remove rt286_adc_event and add
"ADC0 Capture Switch" to mute/unmute ADC mixer.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The wm97xx touchscreen driver binds itself to the snd_ac97 device that gets
registered by the CODEC driver and expects that the device has already been
reset. Before commit 6794f709 ("ASoC: ac97: Drop delayed device
registration") the device was only registered after the probe function of
the CODEC driver had finished running, but starting with the mentioned
commit the device is registered as soon as snd_soc_new_ac97_codec() is
called. This causes the touchscreen driver to no longer work. Modify the
CODEC drivers to use snd_soc_alloc_ac97_codec() instead of
snd_soc_new_ac97_codec() and make sure that the AC'97 device is reset before
the snd_ac97 device gets registered.

Fixes: 6794f709 ("ASoC: ac97: Drop delayed device registration")
Reported-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NManuel Lauss <manuel.lauss@gmail.com>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org