With closed loop support, the clock rate of the DFLL can be adjusted.

The oscillator itself in the DFLL is a free-running oscillator whose
rate is directly determined the supply voltage. However, the DFLL
module contains logic to compare the DFLL output rate to a fixed
reference clock (51 MHz) and make a decision to either lower or raise
the DFLL supply voltage. The DFLL module can then autonomously change
the supply voltage by communicating with an off-chip PMIC via either I2C
or PWM signals. This driver currently supports only I2C.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: NMikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMichael Turquette <mturquette@linaro.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add shared code to support the Tegra DFLL clocksource in open-loop
mode. This root clocksource is present on the Tegra124 SoCs. The
DFLL is the intended primary clock source for the fast CPU cluster.

This code is very closely based on a patch by Paul Walmsley from
December (http://comments.gmane.org/gmane.linux.ports.tegra/15273),
which in turn comes from the internal driver by originally created
by Aleksandr Frid <afrid@nvidia.com>.

Subsequent patches will add support for closed loop mode and drivers
for the Tegra124 fast CPU cluster DFLL devices, which rely on this
code.
Signed-off-by: NPaul Walmsley <pwalmsley@nvidia.com>
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: NMikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMichael Turquette <mturquette@linaro.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>

When split BAR is enabled, the driver needs to dump out the split BAR
registers rather than the original 64bit BAR registers.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

The unsafe doorbell and scratchpad access should display reason when
WARN is called.  Otherwise we get a stack dump without any explanation.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Printouts driver name and version to indicate what is being loaded.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Benchmarking showed a significant performance increase with the MTU size
to 64k instead of 16k.  Change the driver default to 64k.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Instead of using the platform code names, use the correct platform names
to identify the respective Intel NTB hardware.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Disable DMA usage by default, since the CPU provides much better
performance with write combining.  Provide a module parameter to enable
DMA usage when offloading the memcpy is preferred.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Changing the memory window BAR mappings to write combining significantly
boosts the performance.  We will also use memcpy that uses non-temporal
store, which showed performance improvement when doing non-cached
memcpys.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Allocate memory for the NUMA node of the NTB device.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Allocate memory and request the DMA channel for the same NUMA node as
the NTB device.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

When the ntb transport is connecting and waiting for the peer, the debug
console receives lots of debug level messages about the remote qp link
status being down.  Rate limit those messages.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

This is a simple debugging driver that enables the doorbell and
scratch pad registers to be read and written from the debugfs.  This
tool enables more complicated debugging to be scripted from user space.
This driver may be used to test that your ntb hardware and drivers are
functioning at a basic level.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

This is a simple ping pong driver that exercises the scratch pads and
doorbells of the ntb hardware.  This driver may be used to test that
your ntb hardware and drivers are functioning at a basic level.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Add module parameters for the addresses to be used in B2B topology.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Reset the link stats when the link goes down.  In particular, the TX and
RX index and count must be reset, or else the TX side will be sending
packets to the RX side where the RX side is not expecting them.  Reset
all the stats, to be consistent.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

On link down, don't advance RX index to the next entry.  The next entry
should never be valid after receiving the link down flag.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

The same message "qp %d: Link Down\n" was printed at two locations in
ntb_transport.  Change the messages so they are distinct.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Set errata flags for the specific device IDs to which they apply,
instead of the whole Xeon hardware class.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Link training should be enabled in the driver probe for root port mode.
We should not have to wait for transport to be loaded for this to
happen.  Otherwise the ntb device will not show up on the transparent
bridge side of the link.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

The transport was writing and then reading the peer scratch pad,
essentially reading what it just wrote instead of exchanging any
information with the peer.  The transport expects the peer values to be
the same as the local values, so this issue was not obvious.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Change ntb_hw_intel to use the new NTB hardware abstraction layer.

Split ntb_transport into its own driver.  Change it to use the new NTB
hardware abstraction layer.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Abstract the NTB device behind a programming interface, so that it can
support different hardware and client drivers.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

The length of each EDID block is EDID_LENGTH, and number of blocks is
(1 + edid->extensions) - we need to multiply not add them.

This causes wrong EDID to be passed on, and is a regression introduced
by d2ed3436 (drm: Introduce helper for replacing blob properties)
Signed-off-by: NShixin Zeng <zeng.shixin@gmail.com>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Stone <daniels@collabora.com>
[danvet: Add Cc: and fix commit summary.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Eric noticed problems with vhost-scsi and virtio-ccw: vhost-scsi
complained about overwriting values in the config space, which
was triggered by a broken implementation of virtio-ccw's config
get/set routines. It was probably sheer luck that we did not hit
this before.

When writing a value to the config space, the WRITE_CONF ccw will
always write from the beginning of the config space up to and
including the value to be set. If the config space up to the value
has not yet been retrieved from the device, however, we'll end up
overwriting values. Keep track of the known config space and update
if needed to avoid this.

Moreover, READ_CONF will only read the number of bytes it has been
instructed to retrieve, so we must not copy more than that to the
buffer, or we might overwrite trailing values.
Reported-by: NEric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NEric Farman <farman@linux.vnet.ibm.com>
Tested-by: NEric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Use kernel.h macro definition.

Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NJean Delvare <jdelvare@suse.de>

Add pwm[4-7] and the associated pwm[4-7]_mode attributes.
Signed-off-by: NRoger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: NJean Delvare <jdelvare@suse.de>

Revert commit ff284f37 (Revert "ACPICA: Permanently set _REV to
the value '2'.) as the regression introduced by commit b1ef2972
reverted by it is now addressed via a blacklist entry.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The platform firmware on some systems expects Linux to return "5" as
the supported ACPI revision which makes it expose system configuration
information in a special way.

For example, based on what ACPI exports as the supported revision,
Dell XPS 13 (2015) configures its audio device to either work in HDA
mode or in I2S mode, where the former is supposed to be used on Linux
until the latter is fully supported (in the kernel as well as in user
space).

Since ACPI 6 mandates that _REV should return "2" if ACPI 2 or later
is supported by the OS, a subsequent change will make that happen, so
make it possible to override that on systems where "5" is expected to
be returned for Linux to work correctly one them (such as the Dell
machine mentioned above).
Original-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

At the moment the IRQCHIP_DECLARE macro is only declared locally in
drivers/irqchip/irqchip.h. It prevents from using it directly in arch/*
directories whenever irqchip drivers only exist there, which happens in a few
cases (e.g. arc, arm, microblaze and mips).

This patch makes the macro to be globally defined, i.e. in
include/linux/irqchip.h, and thus usable for arch-specific declarations of
irqchip drivers. In this way, it is very similar to what clocksource does (ie
CLOCKSOURCE_OF_DECLARE is defined in include/linux/clocksource.h).

For now, this patch only moves the declaration of the macro
IRQCHIP_DECLARE to the global header 'include/linux/irqchip.h' and make
'drivers/irqchip/irqchip.h' include 'include/linux/irqchip.h'. Later, other
patches will get rid of 'drivers/irqchip/irqchip.h' and modify all the impacted
irqchip drivers.
Signed-off-by: NJoel Porquet <joel@porquet.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1435865565-14114-1-git-send-email-joel@porquet.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Fixes an issue when queue_reuest_irq fails in nvme_setup_io_queues. This
patch initializes all vectors to -1 and resets the vector to -1 in the
case of a failure in queue_request_irq. This avoids the free_irq in
nvme_suspend_queue if the queue did not get an irq.
Signed-off-by: NJon Derrick <jonathan.derrick@intel.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

This patch only moves files to their new locations, before applying the
next two patches adding the NTB Abstraction layer.  Splitting this patch
from the next is intended make distinct which code is changed only due
to moving the files, versus which are substantial code changes in adding
the NTB Abstraction layer.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

After the commit 736e60dd ("OMAPDSS:
componentize omapdss") the dss core device will wait until all the
subdevices have been successfully probed. However, we don't have a
working driver for RFBI, so if RFBI device exists, omapdss will never
get probed.

All the .dtsi files set RFBI as disabled, except am4372.dtsi. This
causes omapdss probe to not finish on AM4 devices.

This patch makes omapdss driver skip adding rfbi device as a
subcomponent, solving the issue.

This should be reverted when we have a working RFBI driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: NFelipe Balbi <balbi@ti.com>

Commit

  debe6a62 ("MIPS: OCTEON: Update octeon-model.h code for new SoCs.")

renamed some SoC model helper functions, but forgot to update the EDAC
drivers resulting in build failures. Fix that.

Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: NDavid Daney <david.daney@cavium.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/1435747132-10954-1-git-send-email-aaro.koskinen@nokia.comSigned-off-by: NBorislav Petkov <bp@suse.de>

ACPICA commit 1a8ec7b83d55c7b957247d685bd1c73f6a012f1e

Remove redundant comment in nseval.c

Link: https://github.com/acpica/acpica/commit/1a8ec7b8Signed-off-by: Ngongzg <gongzhaogang@inspur.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit f51bf8497889a94046820639537165bbd7ccdee6

Adds acclib.h

This patch doesn't affect the Linux kernel.

Link: https://github.com/acpica/acpica/commit/f51bf849Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit 3b1026e0bdd3c32eb6d5d313f3ba0b1fee7597b4
ACPICA commit 00f0dc83f5cfca53b27a3213ae0d7719b88c2d6b
ACPICA commit 47d22a738d0e19fd241ffe4e3e9d4e198e4afc69

Across all of ACPICA. Replace C library macros such as ACPI_STRLEN with the
standard names such as strlen. The original purpose for these macros is
long since obsolete.
Also cast various invocations as necessary. Bob Moore, Jung-uk Kim, Lv Zheng.

Link: https://github.com/acpica/acpica/commit/3b1026e0
Link: https://github.com/acpica/acpica/commit/00f0dc83
Link: https://github.com/acpica/acpica/commit/47d22a73Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NJung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit d4a53a396fe5d384425251b0257f8d125bbed617

Especially for use of the Index operator. For buffers and strings,
only output the actual byte pointed to by the index. For packages,
only print the package element decoded by the index.

Link: https://github.com/acpica/acpica/commit/d4a53a39Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit 3f78b7fb3f98f35d62f532c1891deb748ad196c9

Physical/virtual address flags were reversed.

Link: https://github.com/acpica/acpica/commit/3f78b7fbSigned-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>