The xHCI platform driver calls into usb_add_hcd to register the irq for
its platform device.  It does not want the xHCI generic driver to
register an interrupt for it at all.  The original code did that by
setting the XHCI_BROKEN_MSI quirk, which tells the xHCI driver to not
enable MSI or MSI-X for a PCI host.

Unfortunately, if CONFIG_PCI is enabled, and CONFIG_USB_DW3 is enabled,
the xHCI generic driver will attempt to register a legacy PCI interrupt
for the xHCI platform device in xhci_try_enable_msi().  This will result
in a bogus irq being registered, since the underlying device is a
platform_device, not a pci_device, and thus the pci_device->irq pointer
will be bogus.

Add a new quirk, XHCI_PLAT, so that the xHCI generic driver can
distinguish between a PCI device that can't handle MSI or MSI-X, and a
platform device that should not have its interrupts touched at all.
This quirk may be useful in the future, in case other corner cases like
this arise.

This patch should be backported to kernels as old as 3.9, that
contain the commit 00eed9c8 "USB: xhci:
correctly enable interrupts".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NYu Y Wang <yu.y.wang@intel.com>
Tested-by: NYu Y Wang <yu.y.wang@intel.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org

The function dma_set_mask() tests internally whether the dma_mask pointer
for the device is initialized and fails if the dma_mask pointer is NULL.
On pci platforms, the device dma_mask pointer is initialized, when pci
devices are enumerated, to point to the pci_dev->dma_mask which is 0xffffffff.
However, for non-pci platforms, the dma_mask pointer may not be initialized
and in that case dma_set_mask() will fail.

This patch initializes the dma_mask and the coherent_dma_mask to 32bits
in xhci_plat_probe(), before the call to usb_create_hcd() that sets the
"uses_dma" flag for the usb bus and the call to usb_add_hcd() that creates
coherent dma pools for the usb hcd.

Moreover, a call to dma_set_mask() does not set the device coherent_dma_mask.
Since the xhci-hcd driver calls dma_alloc_coherent() and dma_pool_alloc()
to allocate consistent DMA memory blocks, the coherent DMA address mask
has to be set explicitly.

This patch sets the coherent_dma_mask to 64bits in xhci_gen_setup() when
the xHC is capable for 64-bit DMA addressing.

If dma_set_mask() succeeds, for a given bitmask, it is guaranteed that
the given bitmask is also supported for consistent DMA mappings.

Other changes introduced in this patch are:

- The return value of dma_set_mask() is checked to ensure that the required
  dma bitmask conforms with the host system's addressing capabilities.

- The dma_mask setup code for the non-primary hcd was removed since both
  primary and non-primary hcd refer to the same generic device whose
  dma_mask and coherent_dma_mask are already set during the setup of
  the primary hcd.

- The code for reading the HCCPARAMS register to find out the addressing
  capabilities of xHC was removed since its value is already cached in
  xhci->hccparams.

- hcd->self.controller was replaced with the dev variable since it is
  already available.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Add Device Tree match table to xhci-plat.c. Add DT bindings document.
Signed-off-by: NAl Cooper <alcooperx@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Adds power management support to xHCI platform driver.

This patch facilitates the transition of xHCI host controller
between S0 and S3/S4 power states, during suspend/resume cycles.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: NVikas C Sajjan <vikas.sajjan@linaro.org>
CC: Doug Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Do a release_mem_region of the hcd resource. Without this the
subsequent insertion of module fails in request_mem_region.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.4+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the ioremap_nocache variant of the ioremap API in
order to make sure our memory will be marked uncachable.

This patch should be backported to kernels as old as 3.4, that contain
the commit 3429e91a "usb: host: xhci:
add platform driver support".
Signed-off-by: NRuchika Kharwar <ruchika@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

This adds a fairly simple xhci-platform driver support. Currently it is
used by the dwc3 driver for supporting host mode.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>