Use dev_pm_ops instead of the deprecated legacy suspend/resume for the
max3100 driver.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure we do not make tty-driver callbacks or wait for port to drain
on uninitialised ports (e.g. when open failed) in
tty_port_close_start().

No callback, such as flush_buffer or wait_until_sent, needs to be made
on a port that has never been opened. Neither does it make much sense to
add drain delay for an uninitialised port.

Currently a drain delay of up to two seconds could be added when a tty
fails to open.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move port drain-delay handling to a separate function.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move HUPCL handling to port shutdown so that DTR is dropped also on hang
up (tty_port_close is a noop for hung-up ports).

Also do not try to drop DTR for uninitialised ports where it has never
been raised (e.g. after a failed open).

Note that this is also the current behaviour of serial-core.

Nine drivers currently call tty_port_close_start directly (rather than
through tty_port_close) and seven of them lower DTR as part of their
close (if the port has been initialised). Fixup the remaining two
drivers so that it continues to be lowered also on normal (non-HUP)
close. [ Note that most of those other seven drivers did not expect DTR
to have been dropped by tty_port_close_start in the first place. ]
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to check ASYNC_INITIALISED before raising DTR when waking up
from blocked open in tty_port_block_til_ready.

Currently DTR could get raised at hang up as a blocked process would
raise DTR unconditionally before checking for hang up and returning.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move wake up of processes on blocked-open and modem-status wait queues
to after port shutdown at hangup.

This way the woken up processes can use the ASYNC_INITIALIZED flag to
detect port shutdown.

Note that this is the order currently used by serial-core.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Untangle port-shutdown logic and make sure the initialised flag is
always cleared for non-console ports.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The same as flags, convert to using open/close counts from tty_port.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The same as flags, convert to using *_wait queues from tty_port.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The same as flags, convert to using close delays from tty_port.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Well, all those are unused. They were perhaps copied from generic
serial structure ages ago. Remove them for good.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The return value is not used anywhere, so no need to return anything.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

First, remove STD_FLAGS as the value, or its subvalues
(ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST) is not tested anywhere --
there is no point to initialize flags to that. Second, use flags
member from tty_port when we have it now. So that we do not waste
space.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

tty->hw_stopped is set only by drivers to remember HW state. If it is
never set to 1 in a particular driver, there is no need to check it in
the driver at all. Remove such checks.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are no (and never were any) kgdb fields in uart_ops. Setting
them produces a build error:
drivers/tty/serial/bfin_uart.c:1054:2: error: unknown field 'kgdboc_port_startup' specified in initializer
drivers/tty/serial/bfin_uart.c:1054:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/bfin_uart.c:1054:2: warning: (near initialization for 'bfin_serial_pops.ioctl') [enabled by default]
drivers/tty/serial/bfin_uart.c:1055:2: error: unknown field 'kgdboc_port_shutdown' specified in initializer
drivers/tty/serial/bfin_uart.c:1055:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/bfin_uart.c:1055:2: warning: (near initialization for 'bfin_serial_pops.poll_init') [enabled by default]

Remove them.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

tty->ops->break_ctl cannot be called outside the gap between open and
close. So there is no need to check whether the port is open in
break_ctl in quatech2. Remove the check and also that member
completely.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It allows for cleaning up on a considerable amount of places. They did
port_get, wakeup, kref_put. Now the only thing needed is to call
tty_port_tty_wakeup which does exactly that.

One exception is ifx6x60 where tty_wakeup was open-coded. We now call
tty_wakeup properly there.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Do not dig struct smd_tty_info out of tty_struct using
tty_port_tty_get. It is unnecessarily too complicated, use simple
container_of instead.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The warning is there since 2.1.69 and we have not seen anybody
reporting it in the past decade. Remove the warning now.

tty_get_baud_rate can now be inline. This gives us one less
EXPORT_SYMBOL.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

info is obtained by container_of. It can never be NULL. So do not test
that.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

data_len in jsm_input cannot be zero as we would jump out early in the
function. It also cannot be negative because it is an int and we do
bitwise and with 8192. So remove the check.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Concurrent access to tty->pgrp must be protected with tty->ctrl_lock.
Also, as noted in the comments, reading current->signal->tty is
safe because either,
  1) current->signal->tty is assigned by current, or
  2) current->signal->tty is set to NULL.

NB: for reference, tty_check_change() implements a similar POSIX
check for the ioctls corresponding to tcflush(), tcdrain(),
tcsetattr(), tcsetpgrp(), tcflow() and tcsendbreak().
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

An ldisc reference is insufficient guarantee the foreground process
group is not in the process of being signalled from a hangup.

1) Reads of tty->pgrp must be locked with ctrl_lock
2) The group pid must be referenced for the duration of signalling.
   Because the driver-side is not process-context, a pid reference
   must be acquired.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As noted in the following comment:

  /* FIXME: there is a tiny race here if the receive room check runs
     before the other work executes and empties the buffer (upping
     the receiving room and unthrottling. We then throttle and get
     stuck. This has been observed and traced down by Vincent Pillet/
     We need to address this when we sort out out the rx path locking */

Use new safe throttle/unthrottle functions to re-evaluate conditions
if interrupted by the complement flow control function.
Reported-by: NVincent Pillet <vincentx.pillet@intel.com>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The tty driver can become stuck throttled due to race conditions
between throttle and unthrottle, when the decision to throttle
or unthrottle is conditional. The following example helps to
illustrate the race:

  CPU 0                        |  CPU 1
                               |
if (condition A)               |
                               | <processing such that A not true>
                               | if (!condition A)
                               |     unthrottle()
    throttle()                 |
                               |

Note the converse is also possible; ie.,

  CPU 0                        |  CPU 1
                               |
                               | if (!condition A)
<processing such that A true>  |
if (condition A)               |
    throttle()                 |
                               |     unthrottle()
                               |

Add new throttle/unthrottle functions based on the familiar model
of task state and schedule/wake. For example,

    while (1) {
        tty_set_flow_change(tty, TTY_THROTTLE_SAFE);
        if (!condition)
            break;
        if (!tty_throttle_safe(tty))
            break;
    }
    __tty_set_flow_change(tty, 0);

In this example, if an unthrottle occurs after the condition is
evaluated but before tty_throttle_safe(), then tty_throttle_safe()
will return non-zero, looping and forcing the re-evaluation of
condition.
Reported-by: NVincent Pillet <vincentx.pillet@intel.com>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

2-line function check_unthrottle() is now only called from
n_tty_read(); merge into caller.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently help message of /proc/sysrq-trigger highlight its
upper-case characters, like below:

      SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E)
      memory-full-oom-kill(F) kill-all-tasks(I) ...

this would confuse user trigger sysrq by upper-case character, which is
inconsistent with the real lower-case character registed key.

This inconsistent help message will also lead more confused when
26 upper-case letters put into use in future.

This patch fix it.

Thanks the comments from Andrew and Randy.
Signed-off-by: Nzhangwei(Jovi) <jovi.zhangwei@huawei.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

An exiting session leader can hang if a foreground process is
blocking for line discipline i/o, eg. in n_tty_read(). This happens
because the blocking reader is holding an ldisc reference (indicating
the line discipline is in-use) which prevents __tty_hangup() from
recycling the line discipline. Although waiters are woken before
attempting to gain exclusive access for changing the ldisc, the
blocking reader in this case will not exit the i/o loop since it
has not yet received SIGHUP (because it has not been sent).

Instead, perform signalling first, then recycle the line discipline.

Fixes:

INFO: task init:1 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
init            D 00000000001d7180  2688     1      0 0x00000002
 ffff8800b9acfba8 0000000000000002 00000000001d7180 ffff8800b9b10048
 ffff8800b94cb000 ffff8800b9b10000 00000000001d7180 00000000001d7180
 ffff8800b9b10000 ffff8800b9acffd8 00000000001d7180 00000000001d7180
Call Trace:
 [<ffffffff83db9909>] __schedule+0x2e9/0x3b0
 [<ffffffff83db9b35>] schedule+0x55/0x60
 [<ffffffff83db74ba>] schedule_timeout+0x3a/0x370
 [<ffffffff81182349>] ? mark_held_locks+0xf9/0x130
 [<ffffffff83dbab38>] ? down_failed+0x108/0x200
 [<ffffffff83dbb7ab>] ? _raw_spin_unlock_irq+0x2b/0x80
 [<ffffffff81182608>] ? trace_hardirqs_on_caller+0x128/0x160
 [<ffffffff83dbab61>] down_failed+0x131/0x200
 [<ffffffff83dbbfad>] ? tty_ldisc_lock_pair_timeout+0xcd/0x120
 [<ffffffff83dbae03>] ldsem_down_write+0xd3/0x113
 [<ffffffff83dbbfad>] ? tty_ldisc_lock_pair_timeout+0xcd/0x120
 [<ffffffff8118264d>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff83dbbfad>] tty_ldisc_lock_pair_timeout+0xcd/0x120
 [<ffffffff81c3df60>] tty_ldisc_hangup+0xd0/0x220
 [<ffffffff81c35bd7>] __tty_hangup+0x137/0x4f0
 [<ffffffff81c37c7c>] disassociate_ctty+0x6c/0x230
 [<ffffffff8111290c>] do_exit+0x41c/0x590
 [<ffffffff8107ad34>] ? syscall_trace_enter+0x24/0x2e0
 [<ffffffff81112b4a>] do_group_exit+0x8a/0xc0
 [<ffffffff81112b92>] sys_exit_group+0x12/0x20
 [<ffffffff83dc49d8>] tracesys+0xe1/0xe6
1 lock held by init/1:
 #0: (&tty->ldisc_sem){++++++}, at: [<ffffffff83dbbfad>] tty_ldisc_lock_pair_timeout+0xcd/0x120
Reported-by: NSasha Levin <levinsasha928@gmail.com>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Acked-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the session leader is exiting, signal the foreground group
processes as part of the hangup sequence, instead of after the
hangup is complete. This prepares for hanging up the
line discipline _after_ signalling processes which
may be blocking on ldisc i/o.

Parameterize __tty_hangup() to distinguish between when the
session leader is exiting and all other hangups; signal the
foreground group after signalling the session leader and its
process group, which preserves the original signal order.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Acked-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The interrupt state does not need to be saved, disabled and
restored here; interrupts are already off because this lock
is bracketed by spin_lock_irq/spin_unlock_irq.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Acked-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

__tty_hangup() and tty_vhangup() cannot be called from atomic context,
so locks do not need to preserve the interrupt state (although,
still disable interrupts).
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Acked-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Reduce complexity of __tty_hangup(); separate SIGHUP signalling
into tty_signal_session_leader().
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Acked-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

kfree on NULL pointer is a no-op.
Signed-off-by: NSyam Sidhardhan <s.syam@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Implement console poll for pch_uart, this could enable KGDBoC when
on pch-uart console.
Signed-off-by: NLiang Li <liang.li@windriver.com>
Acked-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NTony Prisk <linux@prisktech.co.nz>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>