The GPIO LEDS driver now has a default state of "keep".  Update the Warp DTS
and platform file to take advantage of this new state.  This removes the
hardcoding of the two LEDs on the Warp.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The kernel reserves the I/O address space from 0x0 to 0xfff for legacy
ISA devices. Change the ranges property for the PCI2ISA bridge to match
the kernels behavior, even if the ranges property isn't used for now.
Signed-off-by: NGerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

For yet unknown reason 4-bit mode doesn't work on MPC8569E-MDS boards,
so make 1-bit mode default. When we resolve the issue, u-boot will
remove sdhci,1-bit-only property from the device tree, while SDHCI
will still work with older u-boots.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds spi and mmc-spi-slot nodes, plus a gpio-controller for
PIXIS' sdcsr bank that is used for managing SPI chip-select and for
reading card's states.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a node for the i2c eeprom and delete the superflous gpio-example.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add device tree source files for various MPC85xx boards from Extreme
Engineering Solutions.  Supported boards include XPedite5370,
XPedite5200, XPedite5301, XPedite5330, and XCalibur1501.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The following series implements basic board support for
the kmeter1 board from keymile, based on a MPC8360.

This series provides the following functionality:

- The board can boot with a serial console on UART1
- Ethernet:
    UCC1 in RGMII mode
    UCC2 in RGMII mode
    UCC4 in RMII mode
    UCC5 in RMII mode
    UCC6 in RMII mode
    UCC7 in RMII mode
    UCC8 in RMII mode

    following patch is necessary for working UCC in RMII mode:

    http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070804.html

- Flash accessed via MTD layer

  On this hardware there is an Intel P30 flash, following patch
  series is necessary for working with this hardware:

  http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070624.html

- I2C using I2C Bus 1 from the MPC8360 cpu
Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add 4 partitions in nor flash. Also fix nor flash bank width bug. The
flash is capable of x8/x16 width but is configured for x8.
Signed-off-by: NKevin Hao <kexin.hao@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

usb0 and usb1 mux settings in the sicrl register were swapped (twice!)
in mpc834x_usb_cfg(), leading to various strange issues with fsl-ehci
and full speed devices.

The USB port config on mpc834x is done using 2 muxes: Port 0 is always
used for MPH port 0, and port 1 can either be used for MPH port 1 or DR
(unless DR uses UTMI phy or OTG, then it uses both ports) - See 8349 RM
figure 1-4..

mpc8349_usb_cfg() had this inverted for the DR, and it also had the bit
positions of the usb0 / usb1 mux settings swapped. It would basically
work if you specified port1 instead of port0 for the MPH controller (and
happened to use ULPI phys), which is what all the 834x dts have done,
even though that configuration is physically invalid.

Instead fix mpc8349_usb_cfg() and adjust the dts files to match reality.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The PCIe MSI interrupts are missing from the device tree source, and
thus were not enabled. This patch adds them.

Tested to work on MPC8315E-RDB with custom FPGA PCIe device.
Signed-off-by: NLeon Woestenberg <leon@sidebranch.com>
Tested-by: NLeon Woestenberg <leon@sidebranch.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Mappings for temperature sensors (adt7461 and lm92) are missing from the
SBC610's DTS file.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

As of commit 40461472 ("Update FSL
esdhc binding"), we use "fsl,esdhc" compatible entry as a base
match. U-Boot will use the same compatible to fixup esdhc nodes.

This patch updates 83xx dts files so that they conform to the new
bindings.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The current device tree for the MPC8272ADS assumes a mapping of 32 MB
of NOR flash at 0xFE00.0000, while there are actually only 8 MB on
the boards, mapped at 0xFF80.0000. When booting an uImage with such a
device tree, the kernel crashes because 0xFE00.0000 is not mapped.

Also introduce aliases for serial[01] and ethernet[01].
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

As subject says, add dts files for Xilinx ML510 reference design with
the PCI host bridge device.
Signed-off-by: NRoderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Now that the 4xx NAND driver is available again in arch/powerpc, let's
enable it on Sequoia. This patch also disables the early debug messages
(CONFIG_PPC_EARLY_DEBUG) in the Sequoia defconfig.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Now that leds-gpio is a proper OF platform driver, the Warp can use
the leds-gpio driver rather than the old out-of-kernel driver.

One side-effect is the leds-gpio driver always turns the leds off
while the old driver left them alone. So we have to set them back to
the correct settings.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The P2020 is a dual e500v2 core based SOC with:
* 3 PCIe controllers
* 2 General purpose DMA controllers
* 2 sRIO controllers
* 3 eTSECS
* USB 2.0
* SDHC
* SPI, I2C, DUART
* enhanced localbus
* and optional Security (P2020E) security w/XOR acceleration

The p2020 DS reference board is pretty similar to the existing MPC85xx
DS boards and has a ULI 1575 connected on one of the PCIe controllers.
Signed-off-by: NTed Peters <Ted.Peters@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

In these configuration we expect to have large amounts of memory (> 4G)
and thus will bounce via swiotlb some region of PCI address space.

The outbound windows were wasting 512M of address space by leaving a
gap between the top of the outbound window and the 4G boundary.  By
moving the top of the outbound window up to the 4G boundary we can
reclaim the vast majority of the 512M (minus space needed for PEXCSRBAR)
and thus reduces the amount of memory we have to bounce.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The MPC8568/9 chips support MSIs on PCIe so no reason not to enable them.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

For serial flash support we need to:

- Add QE Par IO Bank E device tree node, a GPIO from this bank is
  used for SPI chip-select line;
- Add serial-flash node;
- Add proper module alias into of/base.c.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Select HAS_RAPIDIO symbol and add rio nodes for MPC8568E-MDS
and MPC8569E-MDS boards.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Note that eSDHC and DUART0 are mutually exclusive on MPC8569E-MDS
boards. Default option is DUART0, so eSDHC is disabled by default.
U-Boot will fixup device tree if eSDHC should be used instead of
DUART0.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch fixes bogus reg = <> property in the localbus node,
and fixes interrupt property (should be "interrupts").

Also add node for NAND support.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

fsl,exec-units-mask should be 0xbfe to include SNOW unit in
MPC8569E's security engine.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Between the addition of the ecm/mcm law nodes and the fact that the
get_immrbase() has been using the range property of the SoC to determine
the base address of CCSR space we no longer need the reg property at
the soc node level.  It has been ill specified and varied between device
trees to cover either the {e,m}cm-law node, some odd subset of CCSR
space or all of CCSR space.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add fsl,qe-num-riscs and fsl,qe-num-snums to all the devices trees which
have qe node.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The MPC8569 is similiar to the MPC8568.  It doubles the number of
QUICC Engine RISC cores from 2 to 4.  Removes eTSECs, TLU and adds
the eSDHC controller.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The new dts places most of the devices in physical address space
above 32-bits, which allows us to have more than 4GB of RAM present.
Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The cell-index property isn't used on PCI nodes and is ill defined.
Remove it for now and if someone comes up with a good reason and
consistent definition for it we can add it back
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The 'device_type = "soc";' line *is* needed in the DTS for get_immrbase()
to return the correct address.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Preserve I2C clock settings for the Socrates MPC8544 board.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

For enet2 and enet3 the wrong phy-handles have been used in DTS files
of the TQM8548 modules.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Commit 0f73a449 added I2C device nodes
for the LM75 thermal sensor on the TQM85xx modules, unfortunately with
the wrong I2C address. The LM75s are located at address 0x48.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds multi-chip support for the Micron MT29F8G08FAB NAND
flash memory on the TQM8548 modules.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add aliases, and correct CS0 offset to match how u-boot
programs it (this was not a problem with cuImage because
the wrapper would reprogram the localbus to match the device
tree).
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The device_type "soc" is still required for MPC85xx boards.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>