ibmebus is the last remaining user of of_platform_driver and the
conversion to a regular platform driver is trivial.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

Commit 091f0ea3 "tg3: Add New 5719 Read
DMA workaround" added a workaround for TX DMA stall on the 5719. This
workaround needs to be applied to the 5720 as well.

Cc: stable@vger.kernel.org
Reported-by: NRoland Dreier <roland@purestorage.com>
Tested-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sets the protocol selector bits (4:0) of the PHY's MII_ADVERTISE
register (ANAR) when writing ADVERTISE_ALL. The protocol selector bits are
indicating IEEE 803.3u support and are fixed / read-only on some PHYs. Not
setting them correctly on others (like TI DP83630) makes the PHY fall back
to 10M HDX mode which should be avoided.

Tested for TI DP83630 PHY on Microblaze platform.
Signed-off-by: NJens Renner <renner@efe-gmbh.de>
Tested-by: NMichal Simek <monstr@monstr.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was recently found out that GSO on 57710/57711 was broken, due to packets
being sent without a valid IP checksum.

Commit 057cf65e "bnx2x: Fix GSO for 57710/57711 chips" partially fixed this
issue, but failed to set the correct IP checksum when receiving GSO packets
via bridges, as such packets enter bnx2x_tx_split() and the FW flags needed
to calculate IP checksum were erroneously set in the incorrect
buffer descriptor.

This patch re-enables GSO in said scenario for 57710/57711 chips.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no valid MAC address could be obtained from the hardware,
fall back to a randomly generated one.
Signed-off-by: NPavel Machek <pavel@denx.de>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FW was initialized with data from wrong header, this caused TSO packets
have wrong IP csum.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAC addresses assigned by the PF to VFs were not kept in the PF driver
admin table. As a result, displaying the VF MACs from the PF interface
to user space showed zero address where in fact the VF got non-zero
address from the PF, fix that.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VF sense they didn't get MAC address, use random one. This will
address the case of administrator not assigning MAC to the VF through
the PF OS APIs and keep udev happy.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the PF initialization, SRIOV is enabled before the PF is fully initialized.
This allows the kernel to probe the newly-exposed VFs before the PF is ready
to handle them (nested probes).

Have the probe method return the -EPROBE_DEFER value in this situation (instead
of the VF probe method retrying its initialization in a loop, and returning -EIO
on failure). When -EPROBE_DEFER is returned by the VF probe method, the kernel
itself will retry the probe after a suitable delay.

Based upon a suggestion by Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When turning on adaptive_rx under adaptive moderation, the CQ's moderation
count wasn't updated according to rx_frames which resulted in too many
interrupts and bandwidth drop.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During a PCI EEH/AER error recovery flow, if the device did not successfully
restart, the error_detected() hook may be called a second time with a
"perm_failure" state. This patch skips over driver cleanup for the second
invocation of the callback.

Also, Lancer error recovery code is fixed-up to handle these changes.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW does not compute L4 checksum for IP Fragmented packets.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the missing free_netdev() before return from function
qlge_probe() in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function be_get_nic_desc(), it will go through the descriptor array
returned from f/w. By comparing the desc_type field, it determines whether
there is a nic descriptor in the array or not. In the case of no nic
descriptor, this function should return NULL.

The code may return an invalide descriptor, when there is no nic descriptor
in the array and the desc_count is less than MAX_RESOURCE_DESC. In this case,
even there is no nic descriptor, it will still return the lase descriptor
since the i doesn't equal to MAX_RESOURCE_DESC.

This patch fix this issue by returning the descriptor when find it and return
NULL for other cases.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: NXiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commits:

c573972c
1a590434
da2e2c21

They were meant for net-next not net.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit bfd428da ("net: ethernet: sun: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e998fd41 ("net: ethernet: korina: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 3b0aaef8 ("net: ethernet: apple: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MVF is a family while MVF600 is a particular SoC in the family.  We
generally prefer to use SoC rather than family name in compatible string
to define a particular type of fec device.  And this is how fec_dt_ids
works for all those IMX fec variants.  Let's change mvf to mvf600 to
have it work in the same way.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o After change in EPORT features of 82xx adapter, netdev->features needs to
  be updated to reflect EPORT feature updates but driver was manipulating
  netdev->features at wrong place.
o This patch uses netdev_update_features() and .ndo_fix_features() to
  update netdev->features properly.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Code is removed because netdev->trans_start updates made by the driver
will be ignored by the kernel.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix error paths in probe to assign proper error codes to probe return value.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After resetting the device, the driver waits for a signature to be
updated to know that firmware has completed initialization. However, the
call to tg3_poll_fw() is being done too late and we're writing to the
GRC_MODE register before it has completely initialized, causing
contention with firmware.  This logic has existed since day one but is
causing PCIE link to go down randomly at startup on one platform once
every few hundred reboots.

Move the tg3_poll_fw() up to before we write to the GRC_MODE register
after reset.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cures transmit timeout's with DHCP observed
while running under KVM. When the transmit ring is cleaned out,
the Byte Queue Limit values need to be reset.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Starting with commit 91226790
`bnx2x: use FW 7.8.17', the bnx2x driver no longer requests the FW to perform
IP checksums for IPv4 packets.

This behaviour needs to be revised for 57710/57711 chips -
when using GSO, if the driver will not set the IP checksum flag then packets
will be transmitted by the chip without a valid IP checksum, resulting in
a drop of all such packets on the receiver-side.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

8168evl offloaded checksums are wrong since commit
e5195c1f ("r8169: fix 8168evl frame padding.")
pads small packets to 60 bytes (without ethernet checksum). Typical symptoms
appear as UDP checksums which are wrong by the count of added bytes.

It isn't worth compensating. Let the driver checksum.

Due to the skb length changes, TSO code is moved before the Tx descriptor gets
written.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NHolger Hoffstätte <holger.hoffstaette@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add the missing iounmap() before return from gianfar_ptp_probe()
in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the interface is shutdown, the mv643xx_eth driver hits the following
lockdep dump:

=================================
[ INFO: inconsistent lock state ]
3.8.0+ #303 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
NetworkManager/3449 [HC0[0]:SC0[0]:HE1:SE1] takes:
 (_xmit_ETHER#2){+.?...}, at: [<c02828e4>] txq_reclaim+0x60/0x230
{IN-SOFTIRQ-W} state was registered at:
  [<c007e93c>] mark_irqflags+0xf8/0x1c4
  [<c007ee60>] __lock_acquire+0x458/0x9a4
  [<c007f8b0>] lock_acquire+0x60/0x74
  [<c03ea914>] _raw_spin_lock+0x40/0x50
  [<c0334040>] sch_direct_xmit+0xa4/0x2e4
  [<c0320880>] dev_queue_xmit+0x174/0x508
  [<c03953b0>] ip6_finish_output2+0xd0/0x3c4
  [<c03b15bc>] mld_sendpack+0x190/0x368
  [<c03b3204>] mld_ifc_timer_expire+0xc/0x58
  [<c005133c>] call_timer_fn+0x6c/0xe0
  [<c0051588>] run_timer_softirq+0x1d8/0x210
  [<c004c004>] __do_softirq+0xe0/0x1b4
  [<c004c448>] irq_exit+0x64/0x6c
  [<c000f1e0>] handle_IRQ+0x34/0x84
  [<c000e0d0>] __irq_usr+0x30/0x80
irq event stamp: 160603
hardirqs last  enabled at (160603): [<c00c736c>] kfree+0xa8/0xe8
hardirqs last disabled at (160602): [<c00c72e0>] kfree+0x1c/0xe8
softirqs last  enabled at (160304): [<c028260c>] mib_counters_update+0x5ec/0x60c
softirqs last disabled at (160302): [<c03eab8c>] _raw_spin_lock_bh+0x14/0x54

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(_xmit_ETHER#2);
  <Interrupt>
    lock(_xmit_ETHER#2);

 *** DEADLOCK ***

1 lock held by NetworkManager/3449:
 #0:  (rtnl_mutex){+.+.+.}, at: [<c032e664>] rtnetlink_rcv+0xc/0x24

stack backtrace:
[<c0013e34>] (unwind_backtrace+0x0/0xf8) from [<c007e12c>] (print_usage_bug+0x150/0x1d4)
[<c007e12c>] (print_usage_bug+0x150/0x1d4) from [<c007e3f8>] (mark_lock_irq+0x248/0x290)
[<c007e3f8>] (mark_lock_irq+0x248/0x290) from [<c007e598>] (mark_lock+0x158/0x404)
[<c007e598>] (mark_lock+0x158/0x404) from [<c007e97c>] (mark_irqflags+0x138/0x1c4)
[<c007e97c>] (mark_irqflags+0x138/0x1c4) from [<c007ee60>] (__lock_acquire+0x458/0x9a4)
[<c007ee60>] (__lock_acquire+0x458/0x9a4) from [<c007f8b0>] (lock_acquire+0x60/0x74)
[<c007f8b0>] (lock_acquire+0x60/0x74) from [<c03ea914>] (_raw_spin_lock+0x40/0x50)
[<c03ea914>] (_raw_spin_lock+0x40/0x50) from [<c02828e4>] (txq_reclaim+0x60/0x230)
[<c02828e4>] (txq_reclaim+0x60/0x230) from [<c0282ad8>] (txq_deinit+0x24/0xcc)
[<c0282ad8>] (txq_deinit+0x24/0xcc) from [<c0282d28>] (mv643xx_eth_stop+0x1a8/0x1bc)
[<c0282d28>] (mv643xx_eth_stop+0x1a8/0x1bc) from [<c031e314>] (__dev_close_many+0x88/0xcc)
[<c031e314>] (__dev_close_many+0x88/0xcc) from [<c031e380>] (__dev_close+0x28/0x3c)
[<c031e380>] (__dev_close+0x28/0x3c) from [<c0320fa0>] (__dev_change_flags+0x7c/0x134)
[<c0320fa0>] (__dev_change_flags+0x7c/0x134) from [<c03210e0>] (dev_change_flags+0x10/0x48)
[<c03210e0>] (dev_change_flags+0x10/0x48) from [<c032da1c>] (do_setlink+0x1a0/0x730)
[<c032da1c>] (do_setlink+0x1a0/0x730) from [<c032f524>] (rtnl_newlink+0x304/0x4b0)
[<c032f524>] (rtnl_newlink+0x304/0x4b0) from [<c032ef8c>] (rtnetlink_rcv_msg+0x25c/0x2a0)
[<c032ef8c>] (rtnetlink_rcv_msg+0x25c/0x2a0) from [<c03383a0>] (netlink_rcv_skb+0xbc/0xd8)
[<c03383a0>] (netlink_rcv_skb+0xbc/0xd8) from [<c032e674>] (rtnetlink_rcv+0x1c/0x24)
[<c032e674>] (rtnetlink_rcv+0x1c/0x24) from [<c03361d8>] (netlink_unicast_kernel+0x88/0xd4)
[<c03361d8>] (netlink_unicast_kernel+0x88/0xd4) from [<c0337dd0>] (netlink_unicast+0x138/0x180)
[<c0337dd0>] (netlink_unicast+0x138/0x180) from [<c0338020>] (netlink_sendmsg+0x208/0x32c)
[<c0338020>] (netlink_sendmsg+0x208/0x32c) from [<c030ab48>] (sock_sendmsg+0x84/0xa4)
[<c030ab48>] (sock_sendmsg+0x84/0xa4) from [<c030aef4>] (__sys_sendmsg+0x2ac/0x2c4)
[<c030aef4>] (__sys_sendmsg+0x2ac/0x2c4) from [<c030c8ec>] (sys_sendmsg+0x3c/0x68)
[<c030c8ec>] (sys_sendmsg+0x3c/0x68) from [<c000e2e0>] (ret_fast_syscall+0x0/0x3c)

It seems that txq_reclaim() takes the netif tx lock:

        __netif_tx_lock(nq, smp_processor_id());

in a context outside of softirq context, and thus is susceptible to
deadlock should an interrupt occur.

Use __netif_tx_lock_bh()/__netif_tx_unlock_bh() instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 54309fa6 ("net: fec: fix kernel oops when plug/unplug cable many times")
introduced the following 'if' block in the beginning of fec_start():

	if (netif_running(ndev)) {
		netif_device_detach(ndev);
		napi_disable(&fep->napi);
		netif_stop_queue(ndev);
		netif_tx_lock_bh(ndev);
	}

Then later in the end of fec_restart() there is another block that calls the
opposite of each one of these functions.

The correct approach would be to also call them with in the reverse order, so
that we have as result:

	if (netif_running(ndev)) {
		netif_tx_unlock_bh(ndev);
		netif_wake_queue(ndev);
		napi_enable(&fep->napi);
		netif_device_attach(ndev);
	}
Suggested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fec_restart() runs in softirq context and we should use the
netif_tx_lock_bh/netif_tx_unlock_bh() variants to avoid the following warning
that happens since commit 54309fa6 ("net: fec: fix kernel oops when plug/unplug
cable many times"):

[    9.753168] =================================
[    9.757540] [ INFO: inconsistent lock state ]
[    9.761921] 3.10.0-rc1-next-20130514 #13 Not tainted
[    9.766897] ---------------------------------
[    9.771264] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[    9.777288] swapper/0 [HC0[0]:SC1[3]:HE1:SE0] takes:
[    9.782261]  (_xmit_ETHER#2){+.?...}, at: [<c03c24a4>] sch_direct_xmit+0xa0/0x2d4
[    9.789879] {SOFTIRQ-ON-W} state was registered at:
[    9.794769]   [<c0059c60>] __lock_acquire+0x528/0x1bc0
[    9.799953]   [<c005b838>] lock_acquire+0xa0/0x108
[    9.804780]   [<c0441320>] _raw_spin_lock+0x28/0x38
[    9.809702]   [<c02f9fc8>] fec_restart+0x5d0/0x664
[    9.814542]   [<c02fa738>] fec_enet_adjust_link+0xa8/0xc0
[    9.819978]   [<c02f7a28>] phy_state_machine+0x2fc/0x370
[    9.825323]   [<c0035ee0>] process_one_work+0x1c0/0x4a0
[    9.830589]   [<c0036594>] worker_thread+0x138/0x394
[    9.835587]   [<c003c620>] kthread+0xa4/0xb0
[    9.839890]   [<c000e820>] ret_from_fork+0x14/0x34
[    9.844728] irq event stamp: 185984
[    9.848226] hardirqs last  enabled at (185984): [<c00232b0>] local_bh_enable_ip+0x84/0xf0
[    9.856450] hardirqs last disabled at (185983): [<c0023270>] local_bh_enable_ip+0x44/0xf0
[    9.864667] softirqs last  enabled at (185966): [<c0023470>] irq_enter+0x64/0x68
[    9.872099] softirqs last disabled at (185967): [<c0023510>] irq_exit+0x9c/0xd8
[    9.879440]
[    9.879440] other info that might help us debug this:
[    9.885981]  Possible unsafe locking scenario:
[    9.885981]
[    9.891912]        CPU0
[    9.894364]        ----
[    9.896814]   lock(_xmit_ETHER#2);
[    9.900259]   <Interrupt>
[    9.902884]     lock(_xmit_ETHER#2);
[    9.906500]
[    9.906500]  *** DEADLOCK ***
Reported-by: NShawn Guo <shawn.guo@linaro.org>
Suggested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bug here is this code from ipg_nic_hard_start_xmit():

	txfd->tfc &= cpu_to_le64(~IPG_TFC_TFDDONE);

IPG_TFC_TFDDONE is 0x0000000080000000 so it's an unsigned int.  The
negated value is 0x7fffffff but 0xffffffff7fffffff was intended.

The other values in this file don't need to be changed but I did it for
consistency.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 749a2b66 (net/macb: clear tx/rx completion flags in ISR)
introduces clear-on-write on ISR register. This behavior is not always
implemented when using Cadence MACB/GEM and is breaking other platforms.
We are using the Design Configuration Register 1 information and a capability
property to actually activate this clear-on-write behavior on ISR.
Reported-by: NHein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NHein Tibosch <hein_tibosch@yahoo.es>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

3.10-rc1 issues the following warning:

netif_napi_add() called with weight 128 on device eth%d

This patch reduce the weight to 64, using NAPI_POLL_WEIGHT.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to avoid double insertion of  vlan tags into the packet while
handling an asic workaroud (issue introduced by net next Commit bc0c3405)
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

efx_start_datapath() asserts that we can fit 2 RX scatter buffers plus
a software structure, each appropriately aligned, into a single page.
Where L1_CACHE_BYTES == 256 and PAGE_SIZE == 4096, which is the case
on s390, this assertion fails.

The current scatter buffer size is also not a multiple of 64 or 128,
which are more common cache line sizes.  If we can make both the start
and end of a scatter buffer cache-aligned, this will reduce the need
for read-modify-write operations on inter- processor links.

Fix the alignment by reducing EFX_RX_USR_BUF_SIZE to 2048 - 256 ==
1792.  (We could use 2048 - L1_CACHE_BYTES, but EFX_RX_USR_BUF_SIZE
also affects user-level networking where a larger amount of
housekeeping data may be needed.  Although this version of the driver
does not support user-level networking, I prefer to keep scattering
behaviour consistent with the out-of-tree version.)

This still doesn't fix the s390 build because like most architectures
it has NET_IP_ALIGN == 2.  When NET_IP_ALIGN != 0 we cannot achieve
cache line alignment at either the start or end of a scatter buffer,
so there is actually no point in padding the buffers to a multiple of
the cache line size.  All we need is 4-byte alignment of the network
header, so do that.

Adjust the assertions accordingly.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Reported-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The two architectures that define CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
(powerpc and x86) now both define NET_IP_ALIGN as 0, so there is no
need for this optimisation any more.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5725 family of devices (asic rev 5762), corrupts TSO packets where
the buffer is within MSS bytes of a 4G boundary (4G, 8G etc.). Detect
this condition and trigger the workaround path.

Cc: <stable@vger.kernel.org>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the 5718, 5719 and 5720 serdes devices, powering down function 0
results in all the other ports being powered down. Add code to skip
function 0 power down.

v2:
 - Modify tg3_phy_power_bug() function to use a switch instead of a
   complicated if statement. Suggested by Joe Perches.

Cc: <stable@vger.kernel.org>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>