This is the IIO driver for AVIA HX711 ADC which is mostly used in weighting
cells.

The protocol is quite simple and using GPIOs:
One GPIO is used as clock (SCK) while another GPIO is read (DOUT)

The raw value read from the chip is delivered.
To get a weight one needs to subtract the zero offset and scale it.
Signed-off-by: NAndreas Klinger <ak@it-klinger.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add DT bindings for avia,hx711
Add vendor avia to vendor list
Signed-off-by: NAndreas Klinger <ak@it-klinger.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

For some reason the axp288_adc driver was modifying the
AXP288_ADC_TS_PIN_CTRL register, changing bits 0-1 depending on
whether the GP_ADC channel or another channel was written.

These bits control when a bias current is send to the TS_PIN, the
GP_ADC has its own pin and a separate bit in another register to
control the bias current.

Not only does changing when to enable the TS_PIN bias current
(always or only when sampling) when reading the GP_ADC make no sense
at all, the code is modifying these bits is writing the entire register,
assuming that all the other bits have their default value.

So if the firmware has configured a different bias-current for either
pin, then that change gets clobbered by the write, likewise if the
firmware has set bit 2 to indicate that the battery has no thermal sensor,
this will get clobbered by the write.

This commit fixes all this, by simply removing all writes to the
AXP288_ADC_TS_PIN_CTRL register, they are not needed to read the
GP_ADC pin, and can actually be harmful.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Fixes style issue where Alignment doesn't match open parenthesis
Signed-off-by: NScott Matheina <scott@matheina.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/iio/adc/fsl-imx25-gcq.ko | grep alias
$

After this patch:

$ modinfo drivers/iio/adc/fsl-imx25-gcq.ko | grep alias
alias:          of:N*T*Cfsl,imx25-gcqC*
alias:          of:N*T*Cfsl,imx25-gcq
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

buffer.h supplies everything needed for devices using buffers.
buffer_impl.h supplies access to the internals as needed to write
a buffer implementation.

This was really motivated by the mess that turned up in the
kernel-doc documentation pulled in by the new sphinx docs.
It made it clear that our logical separations in headers were
generally terrible.  The buffer case was easy to sort out without
greatly effecting drivers so here it is.
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>

It's bad practice and only done in this fake driver + it breaks my
attempt to take struct buffer opaque. Not worth an access function
as it shouldn't be done anyway.
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>

This is a precursor to the splitting of buffer.h into parts relevant
to buffer implementation vs those for devices using buffers.
struct buffer is about to become opaque as far as the header is
concerned.
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>

These were only getting access to the internals of struct iio_dev via
the include of iio.h within buffer.h.  This should always have been
explicitly included by the buffer implementations themselves.
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>

As a precursor to splitting buffer.h, lets make sure all drivers
include the relevant headers rather than relying on picking them
up from kfifo_buf.h.
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>

Wrong start of kernel doc comment /* -> /**
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>

Ancient legacy of me doing it wrong which it is nice to clear
up whilst we are here.
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>

Nothing uses it outside of core code.
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>

This is a necessary step in taking the buffer implementation
opaque.
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>

This should make it easier to see how the structure is split into
public and private parts - reflected in the generated documentation.

Deliberately use /* instead of /** for the private elements to avoid
warnings when kernel-doc script runs.
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>

Nothing outside of indiustrialio-buffer.c should be using this.
Requires a large amount of juggling of functions to avoid a
forward definition.
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>

The earlier deployed LIS3LV02DL driver had already defined a few
DT bindings that need to be supported by the new more generic
driver and listed as compatible but deprecated bindings in the
documentation.

After this we can start to activate the new driver with the old
systems where applicable.

As part of this enablement: make us depend on the old drivers
not being in use so we don't get a kernel with two competing
drivers.

Cc: devicetree@vger.kernel.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Eliminate the non-standard attributes in_voltage_range and
in_voltage_range_available. Implement in_voltage_scale_available in place
of these attributes and update the SCALE accordingly. The array
scale_avail is introduced to hold the available scale values.
Signed-off-by: NEva Rachel Retuya <eraretuya@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Fixes a warning flagged by checkpatch.pl
Signed-off-by: Nrishabh hardas <rishabheudyptula@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Gravity sensor is a soft sensor, which derives value from
standard accelerometer device by filtering out the acceleration
which is not caused by gravity.

Gravity sensor provides a three dimensional vector indicating
the direction and magnitude of gravity. Typically, this sensor
is used to determine the device's relative orientation in space.
The units and the coordinate system is the same as the one used by
the acceleration sensor.
When a device is at rest, the output of the gravity sensor should
be identical to that of the accelerometer.

More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR59_-_Usages_for_Wearables.pdf

Gravity sensor and accelerometer have similar channels and
share channel usage ids. So the most of the code for accel_3d
can be reused.
Signed-off-by: NSong Hongyan <hongyan.song@intel.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add new channel types support for gravity sensor.

Gravity sensor provides an application-level or physical collection that
identifies a device that measures exclusively the force of Earth's
gravity along any number of axes.

More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR59_-_Usages_for_Wearables.pdfSigned-off-by: NSong Hongyan <hongyan.song@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Signed-off-by: NMatt Ranostay <matt@ranostay.consulting>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Cc: Rob Herring <robh@kernel.org>
Signed-off-by: NMatt Ranostay <matt@ranostay.consulting>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

trivial fix to spelling mistake in iio documentation
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Adds braces to second arm of if else statement.
Signed-off-by: NScott Matheina <scott@matheina.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Signed-off-by: NPeter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds the ACPI/PNP ID. The AD5592/3 driver core is already
designed around the unified device property API.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds the ACPI/PNP ID. The AD5592/3 driver core is already
designed around the unified device property API.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This adds a driver for the Capella Microsystems CM3605 Ambient
Light Sensor and proximity sensor. This is a pretty simple entirely
analog device that is interfaced with the target system using
the POUT (proximity out) and AOUT (ambient light out) signals.

The POUT signal is a simple high/low signal that indicates whether
an object is in proximity, most typically used to detect a face
in front of a mobile device. The signal requires that an infrared
LED is mounted next to the device, making IR light reflect off
the object in proximity and triggering the POUT signal. We grab
a GPIO pin to handle the POUT signal as an interrupt line and
register this as an event channel for the sensor.

Since the proximity sensor requires an IR LED, we add a LED trigger
named "cm3605" so that the infrared LED can just associate with
this trigger to be sure it is always on when the proximity sensor
needs it.

The AOUT is an analog voltage between 0 and 1550 mV that indicate
the LUX value in the ambient light: this is orthogonal to the
proximity sensor functionality. Since this analog voltage needs
to be converted into a digital value, the driver grabs an IIO
channel named "aout" associated with the device.

This patch created a combined ALS and proximity sensor driver.
The former supports raw reads of the LUX value and the latter
will generate proximity events.

To integrate this properly with Linux we also add a supply
regulator for the VDD pin (driving both functions) and add device
tree bindings to define the RSET resistor that in turn configures
the luminosity range of the ALS sensor.

Since the sensor needs to be on more or less constantly, we
restrict the power management to system suspend/resume: we
disable the IR LED and disable the regulator for VDD on suspend
and take them back up on resume.

Tests:
cd /sys/bus/iio/devices/iio:device1
cat in_illuminance_raw
304
(hold hand over sensor)
cat in_illuminance_raw
17
iio_event_monitor cm3605
Found IIO device with name cm3605 with device number 1
(hold hand over sensor)
Event: time: 2444842301447, type: proximity, channel: 0,
  evtype: thresh, direction: falling
(remove hand over sensor)
Event: time: 2445583440706, type: proximity, channel: 0,
  evtype: thresh, direction: rising

Cc: Capella Microsystems <capellamicro@gmail.com>
Cc: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This adds device tree bindings for the Capella Microsystems CM3605
ambient light sensor and short range proximity sensor.

Cc: devicetree@vger.kernel.org
Cc: Capella Microsystems <capellamicro@gmail.com>
Cc: Kevin Tsai <ktsai@capellamicro.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

There is one light sensor type defined in the sensor hub specification,
which has one Illuminance field. It doesn't distinguish between ambient
light sensor or color sensor. Currently it is presented as IIO_INTENSITY
channel. There are some user spaces specifically looking for IIO_LIGHT
channel.
To satisfy such user spaces this change also add a duplicate IIO_LIGHT
channel. The units of measurement of Illuminance field is Lux, so it is
still compatible to IIO ABI.
Signed-off-by: NKweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Both devices are using the same iio_chan_spec to define which settings
are exported with sysfs. Both are properly configured to set/get
sampling frequency for pressure and temperature. They also properly
export available sampling frequencies. The only missing thing is
sampling_frequency sysfs file, which allows to set/get this property
from userspace.

Add sampling frequency to iio channel info mask, so sampling_frequency
file is properly exported using sysfs.
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Datasheet of each device (lps331ap, lps25h, lps001wp, lps22hb) says that
the pressure and temperature data is a 2's complement.

I'm sending this the slow way, as negative pressures on these are pretty
unusual and the nature of the fixing of multiple device introduction patches
will make it hard to apply to older kernels - Jonathan.

Fixes: 217494e5 ("iio:pressure: Add STMicroelectronics pressures driver")
Fixes: 2f5effcb ("iio: pressure-core: st: Expand and rename LPS331AP's channel descriptor")
Fixes: 7885a8ce ("iio: pressure: st: Add support for new LPS001WP pressure sensor")
Fixes: e039e2f5 ("iio:st_pressure:initial lps22hb sensor support")
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This adds documentation for Bosch BMI160 Inertial Measurement Unit
device-tree bindings.
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

From now on we can add bmi160 device to device-tree by specifying
compatible string.
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

From now on we can add bmi160 device to device-tree by specifying
compatible string.
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

according to datasheet complete control register is of 2 bytes.
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5933.pdfSigned-off-by: NNizam Haider <nijam.h@hcl.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Several ADC channels are supported in PMIC which can be used to
measure voltage, temperature, current etc. Different scaling can be
applied on the obtained voltage to report in physical units. Scaling
functionality can be different per channel. Add scaling support per
channel. Every channel present in adc has an unique conversion formula
for obtained voltage. Add support to report in Raw as well as in
processed format. Scaling is applied when processed read is requested
and is not applied when a Raw read is requested.
Signed-off-by: NRama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Several channels are supported in ADC of PMIC which can be used to
measure voltage, temperature, current etc., Hardware provides
readings for all channels in adc code. That adc code needs to be
converted to voltage. Logic for conversion of adc code to voltage
is common for all ADC channels(voltage, temperature, current
.,etc). Implement separate function for generic conversion logic.
Signed-off-by: NRama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The alignment of the #defines at the top of the file is not consistent.
This changes all of the defines to use consistent alignment to improve
the code readability.
Signed-off-by: NBrian Masney <masneyb@onstation.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>