Extend existing driver for Spectrum ASIC to support Spectrum-2 ASIC.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Expose counters ASIC has in the group of RFC 2819 counters that count
number of packets within specific size range.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Virtual Router Redundancy Protocol packets are used to communicate the
state of the Master router associated with the virtual router ID (VRID).

These are link-local multicast packets sent with IP protocol 112 that
are trapped in the router block in the ASIC.

Add a trap for these packets and mark the trapped packets to prevent
them from potentially being re-flooded by the bridge driver.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An IP packet received on a netdev with a macvlan upper whose MAC matches
the packet's destination MAC will be re-injected to the Rx path as if it
was received by the macvlan, and perform an L3 lookup.

Reflect this functionality to the ASIC by programming FDB entries that
will direct MACs of macvlan uppers to the router.

In a similar fashion to router interfaces (RIFs) that are programmed
upon the addition of the first IP address on an interface and destroyed
upon the removal of the last IP address, the FDB entries for the macvlan
are added and destroyed based on the addition of the first and removal
of the last IP address on the macvlan.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to allow more unicast MAC addresses (e.g., VRRP virtual MAC) to
be directed to the router we need to enable macvlan uppers on top of
mlxsw netdevs.

Allow macvlan upper devices on top of mlxsw netdevs and sanitize
configurations that can't work. For example, a macvlan can't be enslaved
to a bridge as without ACLs the device doesn't take the destination MAC
into account when classifying a packet to a bridge instance (i.e., a
FID).
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prepare for Spectrum-2 FW version checking and
make mlxsw_sp_fw_rev_validate() per-ASIC as well as required FW revision
and FW filename.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the flex keys for Spectrum-2 differ not only in blocks definitions
but also in encoding layout, prepare for the implementation and pass
Spectrum/Spectrum-2 specific ops down to mlxsw_afk_create.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To allow easy and clean Spectrum-2 implementation for things that differ
from Spectrum, split the existing ACL TCAM code 3 ways:
1) common code that calls Spectrum/Spectrum-2 specific ops
2) Spectrum ops implementations
3) common C-TCAM code that is going to be shared between Spectrum and
   Spectrum-2 implementations
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since Spectrum-2 has different handling of TCAM, push Spectrum MR TCAM
bits to a separate file accessible by ops which allows to implement
Spectrum-2 specific ops.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Spectrum-2 there is a different implementation of KVD linear
management. Unlike in Spectrum where there is a single index space,
in Spectrum-2 the indexes are per-resource. Also there is need to
explicitly tell HW that an entry is no longer used.
So push out the existing implementation into spectrum1_kvdl.c and
prepare ops infrastructure to allow new implementation in a follow-up.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Spectrum-2 need a slightly different handling of flexible actions. So
put an ops pointer in mlxsw_sp struct and rename it.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call the reoffload tcf_proto_op on all tcf_proto nodes in all chains of a
block when a callback tries to register to a block that already has
offloaded rules. If all existing rules cannot be offloaded then the
registration is rejected. This replaces the previous policy of rejecting
such callback registration outright.

On unregistration of a callback, the rules are flushed for that given cb.
The implementation of block sharing in the NFP driver, for example,
duplicates shared rules to all devs bound to a block. This meant that
rules could still exist in hw even after a device is unbound from a block
(assuming the block still remains active).
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass the extact struct from a tc qdisc add to the block bind function and,
in turn, to the setup_tc ndo of binding device via the tc_block_offload
struct. Pass this back to any block callback registrations to allow
netlink logging of fails in the bind process.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return messages in extack for port split/unsplit errors. e.g.,
    $ devlink port split swp1s1 count 4
    Error: mlxsw_spectrum: Port cannot be split further.
    devlink answers: Invalid argument

    $ devlink port unsplit swp4
    Error: mlxsw_spectrum: Port was not split.
    devlink answers: Invalid argument
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VLAN 1 is internally used for untagged traffic. Prevent creation of
explicit netdevice for that VLAN, because that currently isn't supported
and leads to the NULL pointer dereference cited below.

Fix by preventing creation of VLAN devices with VID of 1 over mlxsw
devices or LAG devices that involve mlxsw devices.

[  327.175816] ================================================================================
[  327.184544] UBSAN: Undefined behaviour in drivers/net/ethernet/mellanox/mlxsw/spectrum_fid.c:200:12
[  327.193667] member access within null pointer of type 'const struct mlxsw_sp_fid'
[  327.201226] CPU: 0 PID: 8983 Comm: ip Not tainted 4.17.0-rc4-petrm_net_ip6gre_headroom-custom-140 #11
[  327.210496] Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2F"/"SA000874", BIOS 4.6.5 03/08/2016
[  327.219872] Call Trace:
[  327.222384]  dump_stack+0xc3/0x12b
[  327.234007]  ubsan_epilogue+0x9/0x49
[  327.237638]  ubsan_type_mismatch_common+0x1f9/0x2d0
[  327.255769]  __ubsan_handle_type_mismatch+0x90/0xa7
[  327.264716]  mlxsw_sp_fid_type+0x35/0x50 [mlxsw_spectrum]
[  327.270255]  mlxsw_sp_port_vlan_router_leave+0x46/0xc0 [mlxsw_spectrum]
[  327.277019]  mlxsw_sp_inetaddr_port_vlan_event+0xe1/0x340 [mlxsw_spectrum]
[  327.315031]  mlxsw_sp_netdevice_vrf_event+0xa8/0x100 [mlxsw_spectrum]
[  327.321626]  mlxsw_sp_netdevice_event+0x276/0x430 [mlxsw_spectrum]
[  327.367863]  notifier_call_chain+0x4c/0x150
[  327.372128]  __netdev_upper_dev_link+0x1b3/0x260
[  327.399450]  vrf_add_slave+0xce/0x170 [vrf]
[  327.403703]  do_setlink+0x658/0x1d70
[  327.508998]  rtnl_newlink+0x908/0xf20
[  327.559128]  rtnetlink_rcv_msg+0x50c/0x720
[  327.571720]  netlink_rcv_skb+0x16a/0x1f0
[  327.583450]  netlink_unicast+0x2ca/0x3e0
[  327.599305]  netlink_sendmsg+0x3e2/0x7f0
[  327.616655]  sock_sendmsg+0x76/0xc0
[  327.620207]  ___sys_sendmsg+0x494/0x5d0
[  327.666117]  __sys_sendmsg+0xc2/0x130
[  327.690953]  do_syscall_64+0x66/0x370
[  327.694677]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  327.699782] RIP: 0033:0x7f4c2f3f8037
[  327.703393] RSP: 002b:00007ffe8c389708 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[  327.711035] RAX: ffffffffffffffda RBX: 000000005b03f53e RCX: 00007f4c2f3f8037
[  327.718229] RDX: 0000000000000000 RSI: 00007ffe8c389760 RDI: 0000000000000003
[  327.725431] RBP: 00007ffe8c389760 R08: 0000000000000000 R09: 00007f4c2f443630
[  327.732632] R10: 00000000000005eb R11: 0000000000000246 R12: 0000000000000000
[  327.739833] R13: 00000000006774e0 R14: 00007ffe8c3897e8 R15: 0000000000000000
[  327.747096] ================================================================================

Fixes: 9589a7b5 ("mlxsw: spectrum: Handle VLAN devices linking / unlinking")
Suggested-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since devlink knows the info needed to generate the physical port name
in a generic way for all devlink users, use the helper to do the job.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change existing setter for split port information into more generic
attrs setter. Alongside with that, allow to set port number and subport
number for split ports.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since switchdev events can trigger SPAN respin, it is necessary that the
data structures are available. Register SPAN first, with a commentary on
what the dependencies are.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of duplicating the decision regarding port forwarding state made
by mlxsw_sp_port_vid_stp_set(), extract the decision-making into a new
function and reuse.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This resolves race during initialization where the resources with
ops are registered before driver and the structures used by occ_get
op is initialized. So keep occ_get callbacks registered only when
all structs are initialized.

The example flows, as it is in mlxsw:
1) driver load/asic probe:
   mlxsw_core
      -> mlxsw_sp_resources_register
        -> mlxsw_sp_kvdl_resources_register
          -> devlink_resource_register IDX
   mlxsw_spectrum
      -> mlxsw_sp_kvdl_init
        -> mlxsw_sp_kvdl_parts_init
          -> mlxsw_sp_kvdl_part_init
            -> devlink_resource_size_get IDX (to get the current setup
                                              size from devlink)
        -> devlink_resource_occ_get_register IDX (register current
                                                  occupancy getter)
2) reload triggered by devlink command:
  -> mlxsw_devlink_core_bus_device_reload
    -> mlxsw_sp_fini
      -> mlxsw_sp_kvdl_fini
	-> devlink_resource_occ_get_unregister IDX
    (struct mlxsw_sp *mlxsw_sp is freed at this point, call to occ get
     which is using mlxsw_sp would cause use-after free)
    -> mlxsw_sp_init
      -> mlxsw_sp_kvdl_init
        -> mlxsw_sp_kvdl_parts_init
          -> mlxsw_sp_kvdl_part_init
            -> devlink_resource_size_get IDX (to get the current setup
                                              size from devlink)
        -> devlink_resource_occ_get_register IDX (register current
                                                  occupancy getter)

Fixes: d9f9b9a4 ("devlink: Add support for resource abstraction")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass struct mlxsw_core instead of devlink since it is nicer within mlxsw
code and we need both structs in mlxsw_sp_kvdl_resources_register()
anyway.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As struct mlxsw_config_profile is mapped to the payload of the FW
command of the same name, resources_query_enable flag does not belong
there. Move it to struct mlxsw_driver.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check should be done directly in mlxsw_pci_config_profile, as for
other profile items. Also, be consistent in naming with the rest and
rename to "used_kvd_sizes".
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should not be part of the struct, as the struct fields
are tightly coupled with the FW command payload of the same name.
Just use the "granularity" define directly, as in other places.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

devlink_resource_ops should be const as the arg of register function is
also const.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new trap for PIMv6 packets. As PIM already has a designated trap
group [ & rate limiter], simply use the same for PIMv6 as well.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In 'auto-neg off' the device have sent AN (auto-negotiation) frames
with the forced speed. Thus, fix it using an_disable_admin field in
Port type and speed (PTYS) register. This field indicates if speed
negotiation frames would be send by the port or not.

Add the field and enable/disable it for 'auto-neg on/off', make the
port to start/stop sending AN (auto-negotiation) frames. Note that for
SwitchX2 the behavior doesn't change (i.e support only AN enabled with
forced speed).
Signed-off-by: NTal Bar <talb@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This new firmware contains:
	- Support for auto-neg disable mode
Signed-off-by: NTal Bar <talb@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

top_hierarchy arg can be determined by comparing parent_resource_id to
DEVLINK_RESOURCE_ID_PARENT_TOP so it does not need to be a separate
argument.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to set some of the fields within 'mbox_config_profile',
since they are reserved and capability mask should be set to zero.
Signed-off-by: NTal Bar <talb@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Spectrum ASIC doesn't support mirroring more than once from a single
binding point (which is a port-direction pair). Therefore detect that a
second binding of a given binding point is attempted.

To that end, extend struct mlxsw_sp_span_inspected_port to track whether
a given binding point is bound or not. Extend
mlxsw_sp_span_entry_port_find() to look for ports based on the full
unique key: port number, direction, and boundness.

Besides fixing the overt bug where configured mirrors are not offloaded,
this also fixes a more subtle bug: mlxsw_sp_span_inspected_port_del()
just defers to mlxsw_sp_span_entry_bound_port_find(), and that used to
find the first port with the right number (disregarding the type). Thus
by adding and removing egress and ingress mirrors in the right order,
one could trick the system into believing it has no egress mirrors when
in fact it did have some. That then caused that
mlxsw_sp_span_port_mtu_update() didn't update mirroring buffer when MTU
was changed.

Fixes: 763b4b70 ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the basic construct in the device is a port-VLAN pair, which can
be bound to a FID or a RIF in order to direct packets to the bridge or
the router, respectively.

Since not all the netdevs are configured with a VLAN (e.g., sw1p1 vs.
sw1p1.10), VID 1 is used to represent these and thus this VID can be
used by both upper devices of mlxsw ports and by the driver itself.

However, this VID is not reference counted and therefore might be freed
prematurely, which can result in various WARNINGs. For example:

$ ip link add name br0 type bridge vlan_filtering 1
$ teamd -t team0 -d -c '{"runner": {"name": "lacp"}}'
$ ip link set dev team0 master br0
$ ip link set dev enp1s0np1 master team0
$ ip address add 192.0.2.1/24 dev enp1s0np1

The enslavement to team0 will fail because team0 already has an upper
and thus vlan_vids_del_by_dev() will be executed as part of team's error
path which will delete VID 1 from enp1s0np1 (added by br0 as PVID). The
WARNING will be generated when the driver will realize it can't find VID
1 on the port and bind it to a RIF.

Fix this by adding a reference count to the VLAN entries on the port, in
a similar fashion to the reference counting used by the corresponding
'vlan_vid_info' structure in the 8021q driver.

Fixes: c57529e1 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Reported-by: NTal Bar <talb@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Tested-by: NTal Bar <talb@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current code uses global variables, adjusts them and passes pointer down
to devlink. With every other mlxsw_core instance, the previously passed
pointer values are rewritten. Fix this by de-globalize the variables and
also memcpy size_params during devlink resource registration.
Also, introduce a convenient size_param_init helper.

Fixes: ef3116e5 ("mlxsw: spectrum: Register KVD resources with devlink")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add TX packets and bytes counters per switch priority per port.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Reviewed-by: NYuval Mintz <yuvalm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some netdevices, for which mlxsw offloads mirroring, may have a
complex relationship between the declared intent and low-level
device configuration.

Trying to accurately track which changes might influence offloading
decisions is finicky and error-prone. Instead, this patch introduces a
function mlxsw_sp_span_entry_respin, which re-queries the configuration
anew and, if different, removes the existing offloads and installs new
ones.

Call this function strategically at event handlers that might influence
the mirroring configuration.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support mirroring to different device types, the functions that
partake in configuring the port analyzer need to be extended to admit
non-trivial SPAN types.

Create a structure where all details of SPAN configuration are kept,
struct mlxsw_sp_span_parms. Also create struct mlxsw_sp_span_entry_ops
to keep per-SPAN-type operations.

Instantiate the latter once for MLXSW_REG_MPAT_SPAN_TYPE_LOCAL_ETH, and
once for a suite of NOP callbacks used for invalidated SPAN entry. Put
the formet as a sole member of a new array mlxsw_sp_span_entry_types,
where all known SPAN types are kept. Introduce a new function,
mlxsw_sp_span_entry_ops(), to look up the right ops suite given a
netdevice.

Change mlxsw_sp_span_mirror_add() to use both parms and ops structures.
Change mlxsw_sp_span_entry_get() and mlxsw_sp_span_entry_create() to
take these as arguments. Modify mlxsw_sp_span_entry_configure() and
mlxsw_sp_span_entry_deconfigure() to dispatch to ops.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the only mirror action supported by mlxsw is mirror to another
mlxsw physical port. Correspondingly, span_entry, which tracks each
mlxsw mirror in the system, currently holds a u8 number of the
destination port.

To extend this system to mirror to gretap and ip6gretap netdevices, have
struct mlxsw_sp_span_entry actually hold the destination netdevice
itself.

This change then trickles down in obvious manner to SPAN module API and
mirror-related interfaces in struct mlxsw_afa_ops.

To prevent use of invalid pointer, NETDEV_UNREGISTER needs to be hooked
and the corresponding SPAN entry invalidated.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of removing span_entry by the port number, allow removing by
SPAN id. That simplifies some code right here, and for mirroring to soft
netdevices, avoids problems with netdevice pointer invalidation and
reuse.

Rename mlxsw_sp_span_entry_find() to mlxsw_sp_span_entry_find_by_port()
and keep it--follow-up patches will make use of it.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The linear part of the KVD memory is sub-divided into multiple parts. This
patch exposes this internal partitions via the resource interface.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After adding size validation logic into core cleanup is required.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>