Commit 15ac408e removed enabled_uart
and OMAP_TAG_UART. This works for mach-omap2, but causes issues on
mach-omap1 for some boards as the mach-omap1 serial.c was muxing
pins based on the enabled_uart flag for 15xx.

Fix this by muxing pins in board-*.c files for the 15xx boards for
the uart ports that had enabled_uart flag set before the commit
above.

Tested on Amsdtrad Delta only.

Note that in the future we should add support for powering down
the uarts with a timer like mach-omap2/serial.c does. Otherwise
the enabled uarts will be blocking retention-while-idle.
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Original message:
The previous value of the jtag_id was set for the omap730.  For the
omap850, this value is different, and this was causing
autodetection to fail.
Reported-by: NCory Maccarrone <darkstar6262@gmail.com>
  Angelo Arrifano <miknix@gmail.com>
  Alistair Buxton <a.j.buxton@gmail.com>
Signed-off-by: NAngelo Arrifano <miknix@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for modem device found on Amstrad E3 (Delta) board.

Based on earlier patch by Jonathan McDowell, available at
http://the.earth.li/pub/e3/2.6.19/ams-delta-modem.patch.
Modified after Ladislav Michl's arch/arm/mach-omap1/board-voiceblue.c.

This patch is dependent on 8250 driver changes getting accepted upstream:
http://git.kernel.org/?p=linux/kernel/git/sfr/linux-next.git;a=commit;h=7053133124d5cdf207c1168c7a0c582a18e12ea7Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP tags are deprecrated so drop them.

Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.

Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.)  After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove ifdefs for io.h
Signed-off-by: NTony Lindgren <tony@atomide.com>

Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.

Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.

In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: NTony Lindgren <tony@atomide.com>

fix the following 'make includecheck' warning:

  arch/arm/mach-omap1/mcbsp.c: mach/irqs.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: NEduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove duplicated #include('s) in
  arch/arm/mach-mx3/devices.c
  arch/arm/mach-omap1/mcbsp.c
  arch/arm/mach-omap2/mcbsp.c
  arch/arm/plat-stmp3xxx/pinmux.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove duplicated #include in arch/arm/mach-omap1/board-nokia770.c.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Some of the N770's MMC configuration options seem to have been
dropped. This patch adds them back in again.

Note that only the .ocr_mask change was /critical/, but I've added the
.max_freq setting back as well, as the original sources had it. Can
anyone confirm if this is unnecessary?

Secondly, there is support in the original code for a 4wire/higher
speed mode. As I don't have the requisite N770 hardware (I think it
was a rev2 N770?) to test this, I can't really add it back.
Signed-off-by: NAndrew de Quincey <adq@lidskialf.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This fixes the positioning of " in MODULE_AUTHOR, which is currently
causing a build failure on latest git with CONFIG_OMAP_MBOX_FWK=m; the
original breakage appears to date from the end of last year in
a5abbbe52b7e89a7633319c5417bd4331f7ac8ed
Signed-Off-By: NJonathan McDowell <noodles@earth.li>
Acked-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Make 770 LCD work by adding clk_add_alias().
Also remove the old unused functions.

Note that the clk_add_alias() could probably be moved
to arch/arm/clkdev.c later on.

Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NImre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com

Update OMAP1-specific PM infrastructure.  This is a sync of what is in
linux-omap for OMAP1.

This mostly de-couples OMAP1 PM from OMAP2/3 PM and renames things
accordingly, and removes omap2/3 specific code from OMAP1 specific
headers.

Original OMAP1 decoupling patch for OMAP PM branch by Paul Walmsley.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch is to sync the core linux-omap PM code with mainline.  This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.

Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.

Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: NJouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Remove unnecessary Kconfig line and allow compile of MBOX_FWK.
Also allow building USB on Nokia 770.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Rename clk_init_one() to clk_preinit() to distinguish its function
from clk_init() and the individual struct clk init functions.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Typo error when requesting for clock for dsp in omap1
Signed-off-by: NArun KS <arunks@mistralsolutions.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Simple simplification...
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Simplify board-h2 MMC setup
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This should be done with GPIO calls. Patches against the
mainline tree welcome to add the necessary working functionality
back.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Pass clocksource pointer to the read() callback for clocksources.  This
allows us to share the callback between multiple instances.

[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Same fix as per a7f8c599, but for OMAP1 instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMatt LaPlante <kernel1@cyberdogtech.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

OMAP_TAGS should vanish soon since they're not generic arm tags.
Most of them can be converted to a platform_data or parsed
from a command line like e.g. serial tag.

For OMAP_TAG_USB we just let boards call omap_usb_init()
passing a pointer to omap_usb_config.

Patch updated by Tony for mainline, basically make
n770 and h4 compile. Also folded in a fix for OSK
by David Brownell <dbrownell@users.sourceforge.net>.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Build system changes.
Signed-off-by: NZebediah C. McClure <zmc@lurian.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

IRQ related changes.
Signed-off-by: NZebediah C. McClure <zmc@lurian.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Changes to base IO subsystem.
Signed-off-by: NZebediah C. McClure <zmc@lurian.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add base support for omap850 cpu.
Signed-off-by: NZebediah C. McClure <zmc@lurian.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Move the defines to the associated board file and remove
the now unnecessary header files.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Move the defines to the board file and remove the now unnecessary
header file.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Move the defines to the board file and remove the now unnecessary
header file.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Also move board-h3.h to mach-omap1.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Also move board-h2.h to mach-omap1.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Move defines to the board file and remove the now
unnecessary headers.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>

linux-omap source commit 33d000c99ee393fe2042f93e8422f94976d276ce
introduces a way to "dry run" clock changes before they're committed.
However, this involves putting logic to handle this into each and
every recalc function, and unfortunately due to the caching, led to
some bugs.

Solve both of issues by making the recalc methods always return the
clock rate for the clock, which the caller decides what to do with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Traditionally, we've tracked the parent/child relationships between
clk structures by setting the child's parent member to point at the
upstream clock.  As a result, when decending the tree, we have had
to scan all clocks to find the children.

Avoid this wasteful scanning by keeping a list of the clock's children.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This fixes booting, and is a step toward fixing things properly:

- Make enable_reg u32 instead of u16
  [rmk: virtual addresses are void __iomem *, not u32]
- Get rid of VIRTUAL_IO_ADDRESS for clocks
- Use __raw_read/write instead of omap_read/write for clock registers

This patch adds a bunch of compile warnings until omap1 clock
also uses offsets.

linux-omap source commit is 9d1dff8638c9e96a401e1885f9948662e9ff9636.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

... which now means no driver requests the "armxor_ck" clock directly.
Also, fix the error handling for clk_get(), ensuring that we propagate
the error returned from clk_get().
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

By providing a dummy ick for OMAP1510 and OMAP310, we avoid having
SoC conditional clock information in i2c-omap.c.  Also, fix the
error handling by making sure we propagate the error returned via
clk_get().
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>