There is some old code in the or51133 firmware loading function that
has no effect.  Left a comment to in case it helps someone trying
to reverse engineer the chip.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Frequency range values in the current driver for the LG TDVS H06xF tuners
appear to have been a transposing of the 5 in the mid range 160-455 instead
of 165-450.
This patch corrects the pll programming for these tuners as per the datasheet.
Signed-off-by: NRusty Scott <rustys@ieee.org>
Signed-off-by: NMac Michaels <wmichaels1@earthlink.net>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

*) Allow forcing the bandselect value with a module parameter to 
facilitate determining the correct bandselect frequencies.
*) Changes the bandselect frequency thresholds based on experiments 
with the above parameter in conjunction with the values in the spec.

Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

*) Sets an additional tuner parameter (demodulator sample gain) that 
wasn't being set before.
*) Removes the low symbol rate tuner parameter tweaks in the previous 
patch -- it appears those tweaks are not necessary with the demodulator 
sample gain set correctly.
*) Cleanup and document the demodulator register initialization sequence.
*) Change set_fec routine to disable FEC auto scan when a specific code 
rate is selected.
*) Remove error message when reported FEC is invalid (which happens 
sometimes when the card has no signal)

Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The previous DISEQC code didn't wait, so it was unreliable

Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Current debug messages at cx24123 are next to useless, since they don't
print the values sent/read to registers. With this patch, debug=1 will
show comprehensive messages. debug=2 will show also read/write operations
at I2C bus.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>

- fixed the reception of channels with low symbol rates.
  ( The VGA1 and VGA2 offsets recommended by cx24109 docs for
  symbol rates from 1 to 5 MSps do not work. I changed them
  to values found experimentally. The charge pump current
  and FILTUNE voltage are now set to values recommended in
  the docs. This improves reception for symbol rates < 15 MSps.
  The values written in the SYSSymbolRate registers are calculated
  with better precision. )
		     
- fixed the cx24123_get_fec() function. It was returning the values
  for DCII mode.
- removed some unused variables

Signed-off-by: Vadim Catana <skystar at moldova.cc>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Unfortunately on the budget-av board, the CAM reset line is tied to the
frontend reset line, so resetting the CAM also zaps the frontend. This
breaks the tda1004x at least, and causes it to fail to tune until the
budget-av module is reloaded. This patch adds an exported function to dvb_frontend
that allows a card to forcibly reinitialise a frontend. The budget-av now
does this on CAM reset, which corrects this problem.
since they do not tie the CAM reset line to the frontend reset line.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Added firmware download comments to or51211 and or51132 Kconfig help text.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Moved duplicated code of ALPS BSRU6 tuner to a standalone file.
Modified av7110 and budget drivers to include the new file.
Signed-off-by: NPerceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Corrected typo for NxtWave NXT200X
- Added "Oren" manufacturer name to menu items for OR51132 and OR51211
- Removed "(pcHDTV HDx000 card)" from Oren frontends menu item names,
  This isn't necessary, as these frontends are selected by the card drivers,
  build configuration (DVB_BT8XX and VIDEO_CX88_DVB).
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- The tuner used in DViCO FusionHDTV DVB-T hybrid is made by Thomson
- renamed tuner and dvb_pll structs accordingly
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add support for the FE6600 tuner used on the DVB-T Hybrid board.
Add support for the Zarlink ZL10353 DVB-T demodulator, which supersedes the
MT352, used on the DViCO FusionHDTV DVB-T Hybrid and later model Plus boards.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Moved duplicated code to separate files.
LNBP21 stuff rewritten from scratch, BSBE1 copied from av7110.c.
Modified budget driver to use the new routines.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

I have a TT C1500 card (saa7146, STV0297) which had problems tuning
channels at QAM128 (like the ones in the Finnish HTV / Welho network).
A fix which seems to work perfectly so far is to change the delay for
QAM128 to the same values as for QAM256 in stv0297_set_frontend(),
Signed-off-by: NMattias Nordstrom <nordstrom@realnode.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch contains the following possible cleanups:
- update the Kconfig help to mention the VP310
- merge vp310_attach and mt312_attach into a new vp310_mt312_attach
  to remove some code duplication
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fixed broken IF-OUT on pinnacle sat board.
Thanks to Edgar Toernig
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Ignore invalid messages on cx24110 frontend.
Thanks to Edgar Toernig
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

I have a TT C1500 card (saa7146, STV0297) which had problems tuning
channels at QAM128 (like the ones in the Finnish HTV / Welho network).
A fix which seems to work perfectly so far is to change the delay for
QAM128 to the same values as for QAM256 in stv0297_set_frontend(),
Signed-off-by: NMattias Nordstrom <nordstrom@realnode.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch contains the following possible cleanups:
- update the Kconfig help to mention the VP310
- merge vp310_attach and mt312_attach into a new vp310_mt312_attach
  to remove some code duplication
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The at76c651 and tda80xx frontends are currently completely unused, IOW
their only effect is making the kernel larger for people accitentially
enabling them.

The current in-kernel drivers differ from the drivers at cvs.tuxbox.org,
and re-adding them when parts of the dbox2 project get merged should be
trivial.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The at76c651 and tda80xx frontends are currently completely unused, IOW
their only effect is making the kernel larger for people accitentially
enabling them.

The current in-kernel drivers differ from the drivers at cvs.tuxbox.org,
and re-adding them when parts of the dbox2 project get merged should be
trivial.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Semaphore to mutex conversion.

The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Set outputs to tristate in sleep mode
- Reduce dangerously high firmware download speed with 16MHz xtal
- added tda827x configuration with GPIOs low
- added comments to stupid looking IIC reads that work around bugs in
  the tda10046.
- some minor updates
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NJose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- rename cb variable names in tuner structures for global consistency
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- rename dvb_pll_tbmv30111in to dvb_pll_samsung_tbmv
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Kill nxt2002 module in favor of nxt200x.
- Repair broken nxt2002 support in the nxt200x module.
- Make the flexcop driver use nxt200x instead of the nxt2002 module for the
  Air2PC 2nd generation PCI card.
- Remove the nxt2002 module from cvs and kernel build.
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- rename dvb_pll_tbmv30111in to dvb_pll_samsung_tbmv
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Kill nxt2002 module in favor of nxt200x.
- Repair broken nxt2002 support in the nxt200x module.
- Make the flexcop driver use nxt200x instead of the nxt2002 module for the
  Air2PC 2nd generation PCI card.
- Remove the nxt2002 module from cvs and kernel build.
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Samsung TBMV30111IN has 6 entries
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- Added knc1 tv star dvb-s support with philips tuner sd1878.
Signed-off-by: NRegis Prevot <regis.prevot@anevia.com>
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

V4L/DVB (3344a): Conversions from kmalloc+memset to k(z|c)alloc


Conversions from kmalloc+memset to k(z|c)alloc.
Signed-off-by: NPanagiotis Issaris <takis@issaris.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Another reason to use:

	ret = foo();
	if (ret < 0)
		goto out;
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- Fixes compiling warning on kernel 2.6.15 with the Intel C compiler. 
- It said drivers/media/dvb/frontends/bcm3510.c(258): 
  warning #592: variable "ret" is used before its value is set
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>

- Reverted objectionable fix in saa7146_hlp.c
- Merged in improved dvb 64-bit fixes from Peter Beutner.
Signed-off-by: NPeter Beutner <p.beutner@gmx.net>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>

- Add DViCO Bluebird firmware to dvb_get_firmware script,
for FusionHDTV USB devices.
- Use usb alt setting 0 for EP4 transfer (dvb-t),
- Use usb alt setting 7 for EP2 transfer (atsc)
- Added comment to lgdt330x.c to indicate support for
DViCO FusionHDTV5 USB Gold.
Thanks to: Jeff Lee <JeffLee@dvico.com>
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>

- add firmware instructions for nxt2002 and nxt2004
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>

- make the firmware dir documentation and comments consistent in the v4l-dvb tree.
Signed-off-by: NVille Skyttä <ville.skytta@iki.fi>
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>