Due to the full duplex nature of the SPI bus, the SPI master
on DaVinci needs transmit to be active even if the tranfer is
only meant to collect receive data.

The current code achieves this by using a temporary zeroed buffer
to provide DMA data in case the transfer does not have a transmit
buffer provided.

However, the transmit DMA is started only if transmit buffer is
provided rendering the temporary buffer unused. Instead the code
relies on a write to SPIDAT1 register to trigger transmit operation.
This however only sends two bytes of data.

Fix this by starting transmit DMA always.

This changes exposes a bug on DM355 where the CSHOLD bit in
SPIDAT1 needs to be written to in between transfers. Handle
that by introducing a "cshold_bug" platform data which is
set to true for DM355.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Do not store DMA channel related information per chip-select since
that information does not depend on the chip select.

The same DMA channels can be used for transfers on all chip-selects
since the transfer happens one-at-a-time.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Remove unnecessary call to davinci_spi_setup_transfer() at the end
of davinci_spi_setup().

davinci_spi_setup_transfer() is registered as the setup_transfer
callback for the bitbang layer and is called independently by
the bitbang layer to setup the transfer before it begins.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The function davinci_spi_bufs_prep() is doing stuff that
davinci_spi_setup() is doing. Eliminate it and move the work
to davinci_spi_setup()
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Configure the data-in, data-out and clock functionality pins
in SPIPC0 register only once during probe. No need to set these
bits for each transfer.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Add support for SPI interrupt mode operation.

Define a per chip-select "io type" variable which
specifies if the transfers on this chip-select should
happen in interrupt mode or polled mode.

Introduce a new function davinci_spi_process_events()
to help consolidate the code between interrupt mode
processing and polled mode processing.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Use the fact that the get_tx and get_rx can now cope with
NULL buffer pointers to simplify the poll mode transfer
code.

While at it, check for SPI errors every transfer rather than
at the end of the whole transfer.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The interrupt mode support as it stands is another version
of poll mode. Even when interrupt mode is selected, the code
tight loops on interrupt status register, rendering it totally
useless. A completion variable is initialized, but never used.

Remove this fake interrupt mode since users can anyway use
poll mode with no functional difference. A usefully implemented
interrupt mode support can be added later.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The completion variable 'done' is unnecessarly initialized by
the function davinci_spi_bufs_dma() where as it is not used
for DMA transfers at all.

Remove the unnecessary initialization.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

In davinci_spi_check_error(), Tx interrupt being set is
treated as error. This function is only meant to flag
bus error conditions and Tx interrupt being set at that
point is not a bus error but rather a driver bug.

Stop checking for Tx interrupt and flagging that as an
IO error.
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Tested-By: NBrian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The variable count in DaVinci SPI driver's private data is
largely unused and its minor use can easily be eliminated.

Remove the variable.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

In the davinci_spi_bufs_dma() function, SPI is briefly disabled
before enabling it immediately back again.

Remove this unnecessary disable.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

In the davinci_spi_{tx|rx}_u{8|16}() functions, check for
buffer pointer being valid before using it. While providing
for better error checking, this change will help simplify
code in the caller.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The EDMA acount (called data_type in davinci_spi_bufs_dma())
is simply the bytes_per_word obtained in the transfer setup
function. The current code calculates the acount value from
bytes_per_word in a convoluted manner. Simplify the code.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The count member of davinci_spi is internal to the driver and
is not shared with framework. Eliminate its unnecessary update.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The struct davinci_spi_slave has a single member. Eliminate it
and store the per-chipselect data in struct davinci_spi directly.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Several members of struct davinci_spi_slave are unused in code.
Remove such members.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Just enabling WAITENA in SPIFMTn register waits for the
enable signal from the slave indefinitely. Allow support
for finite waiting by adding support for c2e delay
(maximum time for addressed slave to respond) and t2e
delay (maximum time for slave to respond after transmit
data finished).

While at it, modify the T2C and C2T defines by prepending
the register name as is the convention followed for other
register field elsewhere in the driver.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Setup chip-select timers values only if timer is enabled
(timer_disbled in spi configuration is false).

As a nice side effect, this patch removes code duplicated in
davinci_spi_bufs_pio() and davinci_spi_bufs_dma().
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Consolidate the setup of SPIFMTn register under
davinci_spi_setup_transfer() simplifying the code
and avoiding unnecessary reads and writes to the
register.

The two inline functions {set|clear}_fmt_bits() can
be eliminated because of this.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Some chip-select specific paramterers like wdelay, parity, usage of
chip-select timers (and the actual timer values) are included in
platform data forcing the same behaviour across all chip-selects.

Create a new davinci_spi_config data structure which can be passed
along using controller_data member of spi_device data structure
on a per-device basis.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The SPI_READY bit of struct spi_device:mode serves the purpose
of letting the SPI master know if the slave can signal if it is
ready for transfer or not.

The 'wait_enable' platform data was duplicating this functionality.
Use the framework provided method of indicating this capability.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Simplify pre-scalar calculation and move it into a seprate
function.

Refuse to correct invalid pre-scalar values silently as this
might lead to unexpected bugs and lower performance. Instead
an error will force users to dig into the root-cause of the
issue.

While at it, remove some device specific checks on the maximum
SPI frequency. As the driver supports the SPI interface
implemented on various devices, it should only take care of core
SPI limitations and leave the device specific handling to platform
code.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Sometimes, the chip selects provided by SPI module are
muxed with other functionality and cannot be used in
some designs. In such cases, it becomes convenient to use
an available GPIO line as chip select.

This patch enables the DaVinci SPI driver to treat specific
GPIO lines as chip selects based on information provided in
platform data.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

On TI DaVinci's SPI controller, the SPIDAT1 register which
controls the chip slect status, also has data transmit register
in the lower 16 bits. Writing to the whole 32-bits triggers
an additional data transmit every time the chip select is disabled.

While most SPI slaves cope-up with this, some cannot. This
patch fixes this by doing a 16-bit write on the upper half
of the SPIDAT1 register

While at it, group the SPIGCR1 register related defines seperately
from SPIDAT1 register defines.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Let davinci_spi_chipselect() perform both activation and
deactivation of chip selects. This lets spi_bitbang fully
control chip select activation, as intended by the SPI API.

With this change, the chip select activation code need not
be duplicated in davinci_spi_bufs_{pio|dma}().

Also, keeping chip select active control is removed as a
platform data and simply controlled using information from
spi_bitbang on whether chip slect should be activated or
de-activated.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Quit writing the same constant value determining the chip-select
mode when no transmissions are in progress in davinci_spi_chipelect().

Instead just setup the SPIDEF register once during probe.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The typecasting of SPI base address to davinci_spi_reg is
unused.

Remove it.
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Tested-By: NBrian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Remove unused defines from code which should help
in easy reading of code.

Also, use the opportuinity to keep the SPIGCR1
register defines together.
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Tested-By: NBrian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The 'pdata' variable is unused in couple of routines.

Remove such occurences.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Cleanup unnecessary white space from various
parts of the file.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Fix the following checkpatch error:

WARNING: unnecessary whitespace before a quoted newline
+       dev_info(&pdev->dev, "Controller at 0x%p \n", davinci_spi->base);
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Commit 451a3c24 ("BKL: remove extraneous #include <smp_lock.h>")
removed the #include line that was the only thing that was surrounded by
the #ifdef/#endif.

So now that #ifdef is guarding nothing at all. Just remove it.
Reported-by: NByeong-ryeol Kim <brofkims@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Arnd Bergmann did an automated scripting run to find left-over instances
of <linux/smp_lock.h>, and had made it trigger it on the normal BKL use
of lock_kernel and unlock_lernel (and apparently release_kernel_lock and
reacquire_kernel_lock too, used by the scheduler).

That resulted in commit 451a3c24 ("BKL: remove extraneous #include
<smp_lock.h>").

However, hardirq.h was the only remaining user of the old
'kernel_locked()' interface, and Arnd's script hadn't checked for that.
So depending on your configuration and what header files had been
included, you would get errors like "implicit declaration of function
'kernel_locked'" during the build.

The right fix is not to just re-instate the smp_lock.h include - it is
to just remove 'kernel_locked()' entirely, since the only use was this
one special low-level detail.  Just make hardirq.h do it directly.

In fact this simplifies and clarifies the code, because some trivial
analysis makes it clear that hardirq.h only ever used _one_ of the two
definitions of kernel_locked(), so we can remove the other one entirely.
Reported-by: NZimny Lech <napohybelskurwysynom2010@gmail.com>
Reported-and-acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Lock_kernel is gone from the code, so the comments should be updated,
too.  nfsd now uses lock_flocks instead of lock_kernel to protect
against posix file locks.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJ. Bruce Fields <bfields@redhat.com>
Cc: linux-nfs@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The big kernel lock has been removed from all these files at some point,
leaving only the #include.

Remove this too as a cleanup.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The stradis driver is on its way out, but it should still be marked
correctly as depending on the big kernel lock.  It could easily be
changed to not require it if someone decides to revive the driver and
port it to v4l2 in the process.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reported-by: NSedat Dilek <sedat.dilek@googlemail.com>
Cc: Nathan Laredo <laredo@gnu.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Making /proc/kallsyms readable only for root by default makes it
slightly harder for attackers to write generic kernel exploits by
removing one source of knowledge where things are in the kernel.

This is the second submit, discussion happened on this on first submit
and mostly concerned that this is just one hole of the sieve ...  but
one of the bigger ones.

Changing the permissions of at least System.map and vmlinux is also
required to fix the same set, but a packaging issue.

Target of this starter patch and follow ups is removing any kind of
kernel space address information leak from the kernel.

[ Side note: the default of root-only reading is the "safe" value, and
  it's easy enough to then override at any time after boot.  The /proc
  filesystem allows root to change the permissions with a regular
  chmod, so you can "revert" this at run-time by simply doing

    chmod og+r /proc/kallsyms

  as root if you really want regular users to see the kernel symbols.
  It does help some tools like "perf" figure them out without any
  setup, so it may well make sense in some situations.  - Linus ]
Signed-off-by: NMarcus Meissner <meissner@suse.de>
Acked-by: NTejun Heo <tj@kernel.org>
Acked-by: NEugene Teo <eugeneteo@kernel.org>
Reviewed-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  nfs: Ignore kmemleak false positive in nfs_readdir_make_qstr
  SUNRPC: Simplify rpc_alloc_iostats by removing pointless local variable
  nfs: trivial: remove unused nfs_wait_event macro
  NFS: readdir shouldn't read beyond the reply returned by the server
  NFS: Fix a couple of regressions in readdir.
  Revert "NFSv4: Fall back to ordinary lookup if nfs4_atomic_open() returns EISDIR"
  Regression: fix mounting NFS when NFSv3 support is not compiled
  NLM: Fix a regression in lockd

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Fix cross-sched-class wakeup preemption
  sched: Fix runnable condition for stoptask
  sched: Use group weight, idle cpu metrics to fix imbalances during idle