[ Upstream commit 0f9e980bf5ee1a97e2e401c846b2af989eb21c61 ]

I'm seeing series of e1000e resets (sometimes endless) at system boot
if something generates tx traffic at this time. In my case this is
netconsole who sends message "e1000e 0000:02:00.0: Some CPU C-states
have been disabled in order to enable jumbo frames" from e1000e itself.
As result e1000_watchdog_task sees used tx buffer while carrier is off
and start this reset cycle again.

[   17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[   17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000
[   23.033336] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[   27.174495] 8021q: 802.1Q VLAN Support v1.8
[   27.174513] 8021q: adding VLAN 0 to HW filter on device eth1
[   30.671724] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation
[   30.898564] netpoll: netconsole: local port 6666
[   30.898566] netpoll: netconsole: local IPv6 address 2a02:6b8:0:80b:beae:c5ff:fe28:23f8
[   30.898567] netpoll: netconsole: interface 'eth1'
[   30.898568] netpoll: netconsole: remote port 6666
[   30.898568] netpoll: netconsole: remote IPv6 address 2a02:6b8:b000:605c:e61d:2dff:fe03:3790
[   30.898569] netpoll: netconsole: remote ethernet address b0:a8:6e:f4:ff:c0
[   30.917747] console [netcon0] enabled
[   30.917749] netconsole: network logging started
[   31.453353] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.185730] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.321840] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.465822] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.597423] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.745417] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.877356] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   35.005441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   35.157376] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   35.289362] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   35.417441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None

This patch flushes tx buffers only once when carrier is off
rather than at each watchdog iteration.
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@yandex-team.ru>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 840018668ce2d96783356204ff282d6c9b0e5f66 ]

When pmu::setup_aux() is called the coresight PMU needs to know which
sink to use for the session by looking up the information in the
event's attr::config2 field.

As such simply replace the cpu information by the complete perf_event
structure and change all affected customers.
Signed-off-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: NSuzuki Poulouse <suzuki.poulose@arm.com>
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/20190131184714.20388-2-mathieu.poirier@linaro.orgSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 77476360f173c127c191bfe8ca8113130ef283b8 ]

[Why]
This fixes an mpc programming error for the following sequence of
atomic commits when pipe split is enabled:

Commit 1: CRTC0 (plane 4, plane 3)

Pipe 0: old_plane_state = A0, new_plane_state = A1,   new_tg = T0
Pipe 1: old_plane_state = B0, new_plane_state = B1,   new_tg = T0
Pipe 2: old_plane_state = A0, new_plane_state = A1,   new_tg = T0
Pipe 3: old_plane_state = B0, new_plane_state = B1,   new_tg = T0

Commit 2: CRTC0 (plane 3), CRTC1 (plane 2)

Pipe 0: old_plane_state = A1, new_plane_state = A2,   new_tg = T0
Pipe 1: old_plane_state = B1, new_plane_state = B2,   new_tg = T1
Pipe 2: old_plane_state = A1, new_plane_state = NULL, new_tg = NULL
Pipe 3: old_plane_state = B1, new_plane_state = NULL, new_tg = NULL

In the second commit the assertion for mpcc in use is hit because
mpcc disconnect never occurs for pipe 1. This is because the stream
changes for pipe 1 and the opp_list is empty.

This sequence occurs when running the
"igt@kms_plane_multiple@atomic-pipe-A-tiling-none" test with two
displays connected.

[How]
Expand the reset condition to include:

"old_pipe_ctx->stream_res.tg != new_pipe_ctx->stream_res.tg"

...but only when the plane state is non-NULL for both old and new.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 5062b797db4103218fa00ee254417b8ecaab7401 ]

[Why]
There are opt1c lock warnings and CRTC read timeouts when running the
"igt@kms_plane@plane-position-hole-dpms-pipe-*" tests. These are
caused by trying to reprogram planes that are not in the current
context.

DPMS off removes the stream from the context. In this case:

new_crtc_state->active_changed = true
new_crtc_state->mode_changed = false

The planes are reprogrammed before the stream is removed from the
context because stream_state->mode_changed = false.

For DPMS adds the stream and planes back to the context:

new_crtc_state->active_changed = true
new_crtc_state->mode_changed = false

The planes are also reprogrammed here before the stream is added to the
context because stream_state->mode_changed = true. They were not
previously in the current context so warnings occur here.

[How]
Set stream_state->mode_changed = true when
new_crtc_state->active_changed = true too.

This prevents reprogramming before the context is applied in DC. The
programming will be done after the context is applied.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NSun peng Li <Sunpeng.Li@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: NTony Cheng <Tony.Cheng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4c6d8fc20b09f9684743afd72e4dbc3f15524479 ]

Add an of_node_put when the result of of_graph_get_remote_port_parent is
not available.

Add a second of_node_put if no encoder is selected (encoder remains NULL).

The semantic match that finds the first problem is as follows
(http://coccinelle.lip6.fr):

// <smpl>
@r exists@
local idexpression e;
expression x;
@@
e = of_graph_get_remote_port_parent(...);
... when != x = e
    when != true e == NULL
    when != of_node_put(e)
    when != of_fwnode_handle(e)
(
return e;
|
*return ...;
)
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f25191bb322dec8fa2979ecb8235643aa42470e1 ]

The following traceback is sometimes seen when booting an image in qemu:

[   54.608293] cdrom: Uniform CD-ROM driver Revision: 3.20
[   54.611085] Fusion MPT base driver 3.04.20
[   54.611877] Copyright (c) 1999-2008 LSI Corporation
[   54.616234] Fusion MPT SAS Host driver 3.04.20
[   54.635139] sysctl duplicate entry: /dev/cdrom//info
[   54.639578] CPU: 0 PID: 266 Comm: kworker/u4:5 Not tainted 5.0.0-rc5 #1
[   54.639578] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
[   54.641273] Workqueue: events_unbound async_run_entry_fn
[   54.641273] Call Trace:
[   54.641273]  dump_stack+0x67/0x90
[   54.641273]  __register_sysctl_table+0x50b/0x570
[   54.641273]  ? rcu_read_lock_sched_held+0x6f/0x80
[   54.641273]  ? kmem_cache_alloc_trace+0x1c7/0x1f0
[   54.646814]  __register_sysctl_paths+0x1c8/0x1f0
[   54.646814]  cdrom_sysctl_register.part.7+0xc/0x5f
[   54.646814]  register_cdrom.cold.24+0x2a/0x33
[   54.646814]  sr_probe+0x4bd/0x580
[   54.646814]  ? __driver_attach+0xd0/0xd0
[   54.646814]  really_probe+0xd6/0x260
[   54.646814]  ? __driver_attach+0xd0/0xd0
[   54.646814]  driver_probe_device+0x4a/0xb0
[   54.646814]  ? __driver_attach+0xd0/0xd0
[   54.646814]  bus_for_each_drv+0x73/0xc0
[   54.646814]  __device_attach+0xd6/0x130
[   54.646814]  bus_probe_device+0x9a/0xb0
[   54.646814]  device_add+0x40c/0x670
[   54.646814]  ? __pm_runtime_resume+0x4f/0x80
[   54.646814]  scsi_sysfs_add_sdev+0x81/0x290
[   54.646814]  scsi_probe_and_add_lun+0x888/0xc00
[   54.646814]  ? scsi_autopm_get_host+0x21/0x40
[   54.646814]  __scsi_add_device+0x116/0x130
[   54.646814]  ata_scsi_scan_host+0x93/0x1c0
[   54.646814]  async_run_entry_fn+0x34/0x100
[   54.646814]  process_one_work+0x237/0x5e0
[   54.646814]  worker_thread+0x37/0x380
[   54.646814]  ? rescuer_thread+0x360/0x360
[   54.646814]  kthread+0x118/0x130
[   54.646814]  ? kthread_create_on_node+0x60/0x60
[   54.646814]  ret_from_fork+0x3a/0x50

The only sensible explanation is that cdrom_sysctl_register() is called
twice, once from the module init function and once from register_cdrom().
cdrom_sysctl_register() is not mutex protected and may happily execute
twice if the second call is made before the first call is complete.

Use a static atomic to ensure that the function is executed exactly once.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a5399db139cb3ad9b8502d8b1bd02da9ce0b9df0 ]

There is no clipping on the x or y axis for logos larger that the framebuffer
size. Therefore: a logo bigger than screen size leads to invalid memory access:

[    1.254664] Backtrace:
[    1.254728] [<c02714e0>] (cfb_imageblit) from [<c026184c>] (fb_show_logo+0x620/0x684)
[    1.254763]  r10:00000003 r9:00027fd8 r8:c6a40000 r7:c6a36e50 r6:00000000 r5:c06b81e4
[    1.254774]  r4:c6a3e800
[    1.254810] [<c026122c>] (fb_show_logo) from [<c026c1e4>] (fbcon_switch+0x3fc/0x46c)
[    1.254842]  r10:c6a3e824 r9:c6a3e800 r8:00000000 r7:c6a0c000 r6:c070b014 r5:c6a3e800
[    1.254852]  r4:c6808c00
[    1.254889] [<c026bde8>] (fbcon_switch) from [<c029c8f8>] (redraw_screen+0xf0/0x1e8)
[    1.254918]  r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:c070d5a0 r5:00000080
[    1.254928]  r4:c6808c00
[    1.254961] [<c029c808>] (redraw_screen) from [<c029d264>] (do_bind_con_driver+0x194/0x2e4)
[    1.254991]  r9:00000000 r8:00000000 r7:00000014 r6:c070d5a0 r5:c070d5a0 r4:c070d5a0

So prevent displaying a logo bigger than screen size and avoid invalid
memory access.
Signed-off-by: NManfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: NMartin Kepplinger <martin.kepplinger@ginzinger.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 93c0970493c71f264e6c3c7caf1ff24a9e1de786 ]

The link status value latches link-down events. To get the current
status we read the register twice in genphy_update_link(). There's
a potential risk that we miss a link-down event in polling mode.
This may cause issues if the user e.g. connects his machine to a
different network.

On the other hand reading the latched value may cause issues in
interrupt mode. Following scenario:

- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
  down and link-down info is latched.
- After aneg has finished link goes up and triggers an interrupt.
  Interrupt handler reads link status, means it reads the latched
  "link is down" info. But there won't be another interrupt as long
  as link stays up, therefore phylib will never recognize that link
  is up.

Deal with both scenarios by reading the register twice in interrupt
mode only.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f368ff188ae4b3ef6f740a15999ea0373261b619 ]

When an application aborts the connection by moving QP from RTS to ERROR,
then iw_cxgb4's modify_rc_qp() RTS->ERROR logic sets the
*srqidxp to 0 via t4_set_wq_in_error(&qhp->wq, 0), and aborts the
connection by calling c4iw_ep_disconnect().

c4iw_ep_disconnect() does the following:
 1. sends up a close_complete_upcall(ep, -ECONNRESET) to libcxgb4.
 2. sends abort request CPL to hw.

But, since the close_complete_upcall() is sent before sending the
ABORT_REQ to hw, libcxgb4 would fail to release the srqidx if the
connection holds one. Because, the srqidx is passed up to libcxgb4 only
after corresponding ABORT_RPL is processed by kernel in abort_rpl().

This patch handle the corner-case by moving the call to
close_complete_upcall() from c4iw_ep_disconnect() to abort_rpl().  So that
libcxgb4 is notified about the -ECONNRESET only after abort_rpl(), and
libcxgb4 can relinquish the srqidx properly.
Signed-off-by: NRaju Rangoju <rajur@chelsio.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 316734fdcf70900a83065360cff11a5826919067 ]

It appears that the mvpp22 can get stuck with SGMII negotiation.  The
symptoms are that in-band negotiation never completes and the partner
(eg, PHY) never reports SGMII link up, or if it supports negotiation
bypass, goes into negotiation bypass mode (which will happen when the
PHY sees that the MAC is alive but gets no response.)

Triggering the PHY end of the link to re-negotiate results in the
bypass bit clearing on the PHY, and then re-setting - indicating that
the problem is at the mvpp22 GMAC end.

Asserting the GMAC reset and de-asserting it resolves the issue.
Arrange to assert the GMAC reset at probe time, and deassert it only
after we have configured the GMAC for the appropriate mode.  This
resolves the issue.
Tested-by: NSven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1136b0728969901a091f0471968b2b76ed14d9ad ]

Waiman reported that on large systems with a large amount of interrupts the
readout of /proc/stat takes a long time to sum up the interrupt
statistics. In principle this is not a problem. but for unknown reasons
some enterprise quality software reads /proc/stat with a high frequency.

The reason for this is that interrupt statistics are accounted per cpu. So
the /proc/stat logic has to sum up the interrupt stats for each interrupt.

This can be largely avoided for interrupts which are not marked as
'PER_CPU' interrupts by simply adding a per interrupt summation counter
which is incremented along with the per interrupt per cpu counter.

The PER_CPU interrupts need to avoid that and use only per cpu accounting
because they share the interrupt number and the interrupt descriptor and
concurrent updates would conflict or require unwanted synchronization.
Reported-by: NWaiman Long <longman@redhat.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NWaiman Long <longman@redhat.com>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NDavidlohr Bueso <dbueso@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-fsdevel@vger.kernel.org
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Daniel Colascione <dancol@google.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Link: https://lkml.kernel.org/r/20190208135020.925487496@linutronix.de

8<-------------

v2: Undo the unintentional layout change of struct irq_desc.

 include/linux/irqdesc.h |    1 +
 kernel/irq/chip.c       |   12 ++++++++++--
 kernel/irq/internals.h  |    8 +++++++-
 kernel/irq/irqdesc.c    |    7 ++++++-
 4 files changed, 24 insertions(+), 4 deletions(-)
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 596b5a5dd1bc2fa019fdaaae522ef331deef927f ]

Currently sysfs_strtoul_clamp() is defined as,
 82 #define sysfs_strtoul_clamp(file, var, min, max)                   \
 83 do {                                                               \
 84         if (attr == &sysfs_ ## file)                               \
 85                 return strtoul_safe_clamp(buf, var, min, max)      \
 86                         ?: (ssize_t) size;                         \
 87 } while (0)

The problem is, if bit width of var is less then unsigned long, min and
max may not protect var from integer overflow, because overflow happens
in strtoul_safe_clamp() before checking min and max.

To fix such overflow in sysfs_strtoul_clamp(), to make min and max take
effect, this patch adds an unsigned long variable, and uses it to macro
strtoul_safe_clamp() to convert an unsigned long value in range defined
by [min, max]. Then assign this value to var. By this method, if bit
width of var is less than unsigned long, integer overflow won't happen
before min and max are checking.

Now sysfs_strtoul_clamp() can properly handle smaller data type like
unsigned int, of cause min and max should be defined in range of
unsigned int too.
Signed-off-by: NColy Li <colyli@suse.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c3b75a2199cdbfc1c335155fe143d842604b1baa ]

dc->writeback_rate_i_term_inverse can be set via sysfs interface. It is
in type unsigned int, and convert from input string by d_strtoul(). The
problem is d_strtoul() does not check valid range of the input, if
4294967296 is written into sysfs file writeback_rate_i_term_inverse,
an overflow of unsigned integer will happen and value 0 is set to
dc->writeback_rate_i_term_inverse.

In writeback.c:__update_writeback_rate(), there are following lines of
code,
      integral_scaled = div_s64(dc->writeback_rate_integral,
                      dc->writeback_rate_i_term_inverse);
If dc->writeback_rate_i_term_inverse is set to 0 via sysfs interface,
a div-zero error might be triggered in the above code.

Therefore we need to add a range limitation in the sysfs interface,
this is what this patch does, use sysfs_stroul_clamp() to replace
d_strtoul() and restrict the input range in [1, UINT_MAX].
Signed-off-by: NColy Li <colyli@suse.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8c27a3953e92eb0b22dbb03d599f543a05f9574e ]

People may set sequential_cutoff of a cached device via sysfs file,
but current code does not check input value overflow. E.g. if value
4294967295 (UINT_MAX) is written to file sequential_cutoff, its value
is 4GB, but if 4294967296 (UINT_MAX + 1) is written into, its value
will be 0. This is an unexpected behavior.

This patch replaces d_strtoi_h() by sysfs_strtoul_clamp() to convert
input string to unsigned integer value, and limit its range in
[0, UINT_MAX]. Then the input overflow can be fixed.
Signed-off-by: NColy Li <colyli@suse.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a91fbda49f746119828f7e8ad0f0aa2ab0578f65 ]

Cache set sysfs entry io_error_halflife is used to set c->error_decay.
c->error_decay is in type unsigned int, and it is converted by
strtoul_or_return(), therefore overflow to c->error_decay is possible
for a large input value.

This patch fixes the overflow by using strtoul_safe_clamp() to convert
input string to an unsigned long value in range [0, UINT_MAX], then
divides by 88 and set it to c->error_decay.
Signed-off-by: NColy Li <colyli@suse.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 99687cdbb3f6c8e32bcc7f37496e811f30460e48 ]

The percpu members of struct sd_data and s_data are declared as:

	struct ... ** __percpu member;

So their type is:

	__percpu pointer to pointer to struct ...

But looking at how they're used, their type should be:

	pointer to __percpu pointer to struct ...

and they should thus be declared as:

	struct ... * __percpu *member;

So fix the placement of '__percpu' in the definition of these
structures.

This addresses a bunch of Sparse's warnings like:

	warning: incorrect type in initializer (different address spaces)
	  expected void const [noderef] <asn:3> *__vpp_verify
	  got struct sched_domain **
Signed-off-by: NLuc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190118144936.79158-1-luc.vanoostenryck@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 54f64d5c983f939901dacc8cfc0983727c5c742e ]

Since the 5.0 merge window opened, I've been seeing frequent
crashes on suspend and reboot with the trace:

[   36.911170] Unable to handle kernel paging request at virtual address ffffff801153d660
[   36.912769] Unable to handle kernel paging request at virtual address ffffff800004b564
...
[   36.950666] Call trace:
[   36.950670]  queued_spin_lock_slowpath+0x1cc/0x2c8
[   36.950681]  _raw_spin_lock_irqsave+0x64/0x78
[   36.950692]  complete+0x28/0x70
[   36.950703]  ffs_epfile_io_complete+0x3c/0x50
[   36.950713]  usb_gadget_giveback_request+0x34/0x108
[   36.950721]  dwc3_gadget_giveback+0x50/0x68
[   36.950723]  dwc3_thread_interrupt+0x358/0x1488
[   36.950731]  irq_thread_fn+0x30/0x88
[   36.950734]  irq_thread+0x114/0x1b0
[   36.950739]  kthread+0x104/0x130
[   36.950747]  ret_from_fork+0x10/0x1c

I isolated this down to in ffs_epfile_io():
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/usb/gadget/function/f_fs.c#n1065

Where the completion done is setup on the stack:
  DECLARE_COMPLETION_ONSTACK(done);

Then later we setup a request and queue it, and wait for it:
  if (unlikely(wait_for_completion_interruptible(&done))) {
    /*
    * To avoid race condition with ffs_epfile_io_complete,
    * dequeue the request first then check
    * status. usb_ep_dequeue API should guarantee no race
    * condition with req->complete callback.
    */
    usb_ep_dequeue(ep->ep, req);
    interrupted = ep->status < 0;
  }

The problem is, that we end up being interrupted, dequeue the
request, and exit.

But then the irq triggers and we try calling complete() on the
context pointer which points to now random stack space, which
results in the panic.

Alan Stern pointed out there is a bug here, in that the snippet
above "assumes that usb_ep_dequeue() waits until the request has
been completed." And that:

    wait_for_completion(&done);

Is needed right after the usb_ep_dequeue().

Thus this patch implements that change. With it I no longer see
the crashes on suspend or reboot.

This issue seems to have been uncovered by behavioral changes in
the dwc3 driver in commit fec9095bdef4e ("usb: dwc3: gadget:
remove wait_end_transfer").

Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Zeng Tao <prime.zeng@hisilicon.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Thinh Nguyen <thinh.nguyen@synopsys.com>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Jerry Zhang <zhangjerry@google.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Vincent Pelletier <plr.vincent@gmail.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1863008369ae0407508033b4b00f98b985adeb15 ]

WCN3990 supports shadow registers write operation support
for copy engine for regular operation in powersave mode.

Since WCN3990 is a 64-bit target, the shadow register
implementation needs to be done in the copy engine handlers
for 64-bit target. Currently the shadow register implementation
is present in the 32-bit target handlers of copy engine.

Fix the shadow register copy engine write operation
implementation for 64-bit target(WCN3990).

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1

Fixes: b7ba83f7 ("ath10k: add support for shadow register for WNC3990")
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit d9c0b2afe820fa3b3f8258a659daee2cc71ca3ef ]

BE dai links only have internal PCM's and their substream ops may
not be set. Suspending these PCM's will result in their
 ops->trigger() being invoked and cause a kernel oops.
So skip suspending PCM's if their ops are NULL.

[ NOTE: this change is required now for following the recent PCM core
  change to get rid of snd_pcm_suspend() call.  Since DPCM BE takes
  the runtime carried from FE while keeping NULL ops, it can hit this
  bug.  See details at:
     https://github.com/thesofproject/linux/pull/582
  -- tiwai ]
Signed-off-by: NRanjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 29f0023d01f063feacfc404f0446905aee4f82ee ]

According to the Odroid-C1+ schematics the Ethernet TXD1 signal is
routed to GPIOH_5 and the TXD0 signal is routed to GPIOH_6.
The public S805 datasheet shows that TXD0 can be routed to DIF_2_P and
TXD1 can be routed to DIF_2_N instead.

The pin groups eth_txd0_0 (GPIOH_6) and eth_txd0_1 (DIF_2_P) are both
configured as Ethernet TXD0 and TXD1 data lines in meson8b.dtsi. At the
same time eth_txd1_0 (GPIOH_5) and eth_txd1_1 (DIF_2_N) are configured
as TXD0 and TXD1 data lines as well.
This results in a bad Ethernet receive performance. Presumably this is
due to the eth_txd0 and eth_txd1 signal being routed to the wrong pins.
As a result of that data can only be transmitted on eth_txd2 and
eth_txd3. However, I have no scope to fully confirm this assumption.

The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
  SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
  SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit  0: eth_rxd1 (DIF_0_P)
- register 6 bit  1: eth_rxd0 (DIF_0_N)
- register 6 bit  2: eth_rx_dv (DIF_1_P)
- register 6 bit  3: eth_rx_clk (DIF_1_N)
- register 6 bit  6: eth_tx_en (DIF_3_P)
- register 6 bit  8: eth_ref_clk (DIF_3_N)
- register 6 bit  9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)

Drop the eth_txd0_1 and eth_txd1_1 groups from eth_rgmii_pins to fix the
Ethernet transmit performance on Odroid-C1. Also add the eth_rxd2 and
eth_rxd3 groups so we don't rely on the bootloader to set them up.

iperf3 statistics before this change:
- transmitting from Odroid-C1: 741 Mbits/sec (0 retries)
- receiving on Odroid-C1: 199 Mbits/sec (1713 retries)

iperf3 statistics after this change:
- transmitting from Odroid-C1: 667 Mbits/sec (0 retries)
- receiving on Odroid-C1: 750 Mbits/sec (0 retries)

Fixes: b9644654 ("ARM: dts: meson8b: extend ethernet controller description")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Tested-by: NEmiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: NEmiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit de9c0d49d85dc563549972edc5589d195cd5e859 ]

While building arm32 allyesconfig, I ran into the following errors:

  arch/arm/lib/xor-neon.c:17:2: error: You should compile this file with
  '-mfloat-abi=softfp -mfpu=neon'

  In file included from lib/raid6/neon1.c:27:
  /home/nathan/cbl/prebuilt/lib/clang/8.0.0/include/arm_neon.h:28:2:
  error: "NEON support not enabled"

Building V=1 showed NEON_FLAGS getting passed along to Clang but
__ARM_NEON__ was not getting defined. Ultimately, it boils down to Clang
only defining __ARM_NEON__ when targeting armv7, rather than armv6k,
which is the '-march' value for allyesconfig.

>From lib/Basic/Targets/ARM.cpp in the Clang source:

  // This only gets set when Neon instructions are actually available, unlike
  // the VFP define, hence the soft float and arch check. This is subtly
  // different from gcc, we follow the intent which was that it should be set
  // when Neon instructions are actually available.
  if ((FPU & NeonFPU) && !SoftFloat && ArchVersion >= 7) {
    Builder.defineMacro("__ARM_NEON", "1");
    Builder.defineMacro("__ARM_NEON__");
    // current AArch32 NEON implementations do not support double-precision
    // floating-point even when it is present in VFP.
    Builder.defineMacro("__ARM_NEON_FP",
                        "0x" + Twine::utohexstr(HW_FP & ~HW_FP_DP));
  }

Ard Biesheuvel recommended explicitly adding '-march=armv7-a' at the
beginning of the NEON_FLAGS definitions so that __ARM_NEON__ always gets
definined by Clang. This doesn't functionally change anything because
that code will only run where NEON is supported, which is implicitly
armv7.

Link: https://github.com/ClangBuiltLinux/linux/issues/287Suggested-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Reviewed-by: NNick Desaulniers <ndesaulniers@google.com>
Reviewed-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 13f5251fd17088170c18844534682d9cab5ff5aa ]

For bridge(br_flood) or broadcast/multicast packets, they could clone
skb with unconfirmed conntrack which break the rule that unconfirmed
skb->_nfct is never shared.  With nfqueue running on my system, the race
can be easily reproduced with following warning calltrace:

[13257.707525] CPU: 0 PID: 12132 Comm: main Tainted: P        W       4.4.60 #7744
[13257.707568] Hardware name: Qualcomm (Flattened Device Tree)
[13257.714700] [<c021f6dc>] (unwind_backtrace) from [<c021bce8>] (show_stack+0x10/0x14)
[13257.720253] [<c021bce8>] (show_stack) from [<c0449e10>] (dump_stack+0x94/0xa8)
[13257.728240] [<c0449e10>] (dump_stack) from [<c022a7e0>] (warn_slowpath_common+0x94/0xb0)
[13257.735268] [<c022a7e0>] (warn_slowpath_common) from [<c022a898>] (warn_slowpath_null+0x1c/0x24)
[13257.743519] [<c022a898>] (warn_slowpath_null) from [<c06ee450>] (__nf_conntrack_confirm+0xa8/0x618)
[13257.752284] [<c06ee450>] (__nf_conntrack_confirm) from [<c0772670>] (ipv4_confirm+0xb8/0xfc)
[13257.761049] [<c0772670>] (ipv4_confirm) from [<c06e7a60>] (nf_iterate+0x48/0xa8)
[13257.769725] [<c06e7a60>] (nf_iterate) from [<c06e7af0>] (nf_hook_slow+0x30/0xb0)
[13257.777108] [<c06e7af0>] (nf_hook_slow) from [<c07f20b4>] (br_nf_post_routing+0x274/0x31c)
[13257.784486] [<c07f20b4>] (br_nf_post_routing) from [<c06e7a60>] (nf_iterate+0x48/0xa8)
[13257.792556] [<c06e7a60>] (nf_iterate) from [<c06e7af0>] (nf_hook_slow+0x30/0xb0)
[13257.800458] [<c06e7af0>] (nf_hook_slow) from [<c07e5580>] (br_forward_finish+0x94/0xa4)
[13257.808010] [<c07e5580>] (br_forward_finish) from [<c07f22ac>] (br_nf_forward_finish+0x150/0x1ac)
[13257.815736] [<c07f22ac>] (br_nf_forward_finish) from [<c06e8df0>] (nf_reinject+0x108/0x170)
[13257.824762] [<c06e8df0>] (nf_reinject) from [<c06ea854>] (nfqnl_recv_verdict+0x3d8/0x420)
[13257.832924] [<c06ea854>] (nfqnl_recv_verdict) from [<c06e940c>] (nfnetlink_rcv_msg+0x158/0x248)
[13257.841256] [<c06e940c>] (nfnetlink_rcv_msg) from [<c06e5564>] (netlink_rcv_skb+0x54/0xb0)
[13257.849762] [<c06e5564>] (netlink_rcv_skb) from [<c06e4ec8>] (netlink_unicast+0x148/0x23c)
[13257.858093] [<c06e4ec8>] (netlink_unicast) from [<c06e5364>] (netlink_sendmsg+0x2ec/0x368)
[13257.866348] [<c06e5364>] (netlink_sendmsg) from [<c069fb8c>] (sock_sendmsg+0x34/0x44)
[13257.874590] [<c069fb8c>] (sock_sendmsg) from [<c06a03dc>] (___sys_sendmsg+0x1ec/0x200)
[13257.882489] [<c06a03dc>] (___sys_sendmsg) from [<c06a11c8>] (__sys_sendmsg+0x3c/0x64)
[13257.890300] [<c06a11c8>] (__sys_sendmsg) from [<c0209b40>] (ret_fast_syscall+0x0/0x34)

The original code just triggered the warning but do nothing. It will
caused the shared conntrack moves to the dying list and the packet be
droppped (nf_ct_resolve_clash returns NF_DROP for dying conntrack).

- Reproduce steps:

+----------------------------+
|          br0(bridge)       |
|                            |
+-+---------+---------+------+
  | eth0|   | eth1|   | eth2|
  |     |   |     |   |     |
  +--+--+   +--+--+   +---+-+
     |         |          |
     |         |          |
  +--+-+     +-+--+    +--+-+
  | PC1|     | PC2|    | PC3|
  +----+     +----+    +----+

iptables -A FORWARD -m mark --mark 0x1000000/0x1000000 -j NFQUEUE --queue-num 100 --queue-bypass

ps: Our nfq userspace program will set mark on packets whose connection
has already been processed.

PC1 sends broadcast packets simulated by hping3:

hping3 --rand-source --udp 192.168.1.255 -i u100

- Broadcast racing flow chart is as follow:

br_handle_frame
  BR_HOOK(NFPROTO_BRIDGE, NF_BR_PRE_ROUTING, br_handle_frame_finish)
  // skb->_nfct (unconfirmed conntrack) is constructed at PRE_ROUTING stage
  br_handle_frame_finish
    // check if this packet is broadcast
    br_flood_forward
      br_flood
        list_for_each_entry_rcu(p, &br->port_list, list) // iterate through each port
          maybe_deliver
            deliver_clone
              skb = skb_clone(skb)
              __br_forward
                BR_HOOK(NFPROTO_BRIDGE, NF_BR_FORWARD,...)
                // queue in our nfq and received by our userspace program
                // goto __nf_conntrack_confirm with process context on CPU 1
    br_pass_frame_up
      BR_HOOK(NFPROTO_BRIDGE, NF_BR_LOCAL_IN,...)
      // goto __nf_conntrack_confirm with softirq context on CPU 0

Because conntrack confirm can happen at both INPUT and POSTROUTING
stage.  So with NFQUEUE running, skb->_nfct with the same unconfirmed
conntrack could race on different core.

This patch fixes a repeating kernel splat, now it is only displayed
once.
Signed-off-by: NChieh-Min Wang <chiehminw@synology.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a39f15b9644fac3f950f522c39e667c3af25c588 ]

Since kprobe itself depends on RCU, probing on RCU debug
routine can cause recursive breakpoint bugs.

Prohibit probing on RCU debug routines.

int3
 ->do_int3()
   ->ist_enter()
     ->RCU_LOCKDEP_WARN()
       ->debug_lockdep_rcu_enabled() -> int3
Signed-off-by: NMasami Hiramatsu <mhiramat@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrea Righi <righi.andrea@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/154998807741.31052.11229157537816341591.stgit@devboxSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 02106f883cd745523f7766d90a739f983f19e650 ]

Since kprobe breakpoing handler is using bsearch(), probing on this
routine can cause recursive breakpoint problem.

int3
 ->do_int3()
   ->ftrace_int3_handler()
     ->ftrace_location()
       ->ftrace_location_range()
         ->bsearch() -> int3

Prohibit probing on bsearch().
Signed-off-by: NAndrea Righi <righi.andrea@gmail.com>
Acked-by: NMasami Hiramatsu <mhiramat@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/154998813406.31052.8791425358974650922.stgit@devboxSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 3aa415dd2128e478ea3225b59308766de0e94d6b ]

The get_metadata() test requires real root, so let's skip it if we're not
real root.

Note that I used XFAIL here because that's what the test does later if
CONFIG_CHEKCKPOINT_RESTORE happens to not be enabled. After looking at the
code, there doesn't seem to be a nice way to skip tests defined as TEST(),
since there's no return code (I tried exit(KSFT_SKIP), but that didn't work
either...). So let's do it this way to be consistent, and easier to fix
when someone comes along and fixes it.
Signed-off-by: NTycho Andersen <tycho@tycho.ws>
Acked-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NShuah Khan <shuah@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit cecf3e3e0803462335e25d083345682518097334 ]

This commit refactors the chassis-type detection introduced by
commit 53fa1f6e ("ACPI / video: Only default only_lcd to true on
Win8-ready _desktops_") (where desktop means anything without a builtin
screen).

The DMI chassis_type is an unsigned integer, so rather then doing a
whole bunch of string-compares on it, convert it to an int and feed
the result to a switch case.

Note the switch case uses hex values, this is done because the spec
uses hex values too. This changes the check for "Main Server Chassis"
from checking for 11 decimal to 11 hexadecimal, this is a bug fix,
the original check for 11 decimal was wrong.

Fixes: 53fa1f6e ("ACPI / video: Only default only_lcd to true ...")
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[ rjw: Drop redundant return statements ]
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c6ac9f9fb98851f47b978a9476594fc3c477a34d ]

Allocator swaps the pending requests with 0 when it starts
working. This means that relying on it n RX path to decide if
to move to emergency is not always a good idea, since it may
be zero, but there are still a lot of unallocated RBs in the
system. Change allocator to decrement the pending requests on
real time. It is more expensive since it accesses the atomic
variable more times, but it gives the RX path a better idea
of the system's status.
Reported-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Fixes: 868a1e863f95 ("iwlwifi: pcie: avoid empty free RB queue")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 2187d87eacd46f6214ce3dc9cfd7a558375a4153 ]

On IBM z13 machine types 2964 and 2965 the descriptor
sizes for sampling and diagnostic sampling entries
might be missing in the trailer entry and are set to zero.

This leads to a perf report failure when processing diagnostic
sampling entries.

This patch adds missing descriptor sizes when the trailer entry
contains zero for these fields.

Output before:
  [root@s38lp82 perf]#  ./perf report --stdio | fgrep Samples
  0xabbf0 [0x8]: failed to process type: 68
  Error:
  failed to process sample
  [root@s38lp82 perf]#

Output after:
  [root@s38lp82 perf]#  ./perf report --stdio | fgrep Samples
  # Total Lost Samples: 0
  # Samples: 3K of event 'SF_CYCLES_BASIC_DIAG'
  # Samples: 162  of event 'CF_DIAG'
  [root@s38lp82 perf]#

Fixes: 2b1444f2 ("perf report: Add raw report support for s390 auxiliary trace")
Signed-off-by: NThomas Richter <tmricht@linux.ibm.com>
Reviewed-by: NHendrik Brueckner <brueckner@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20190211100627.85714-1-tmricht@linux.ibm.comSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 5ddb0869bfc1bca6cfc592c74c64a026f936638c ]

I've stumbled upon a kernel crash and the logs
pointed me towards the lp5562 driver:

> <4>[306013.841294] lp5562 0-0030: Direct firmware load for lp5562 failed with error -2
> <4>[306013.894990] lp5562 0-0030: Falling back to user helper
> ...
> <3>[306073.924886] lp5562 0-0030: firmware request failed
> <1>[306073.939456] Unable to handle kernel NULL pointer dereference at virtual address 00000000
> <4>[306074.251011] PC is at _raw_spin_lock+0x1c/0x58
> <4>[306074.255539] LR is at release_firmware+0x6c/0x138
> ...

After taking a look I noticed firmware_release()
could be called with either NULL or a dangling
pointer.

Fixes: 10c06d17 ("leds-lp55xx: support firmware interface")
Signed-off-by: NMichal Kazior <michal@plume.com>
Signed-off-by: NJacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 538bcaa6261b77e71d37f5596c33127c1a3ec3f7 ]

The jbd2 superblock is lockless now, so there is probably a race
condition between writing it so disk and modifing contents of it, which
may lead to checksum error. The following race is the one case that we
have captured.

jbd2                                fsstress
jbd2_journal_commit_transaction
 jbd2_journal_update_sb_log_tail
  jbd2_write_superblock
   jbd2_superblock_csum_set         jbd2_journal_revoke
                                     jbd2_journal_set_features(revork)
                                     modify superblock
   submit_bh(checksum incorrect)

Fix this by locking the buffer head before modifing it.  We always
write the jbd2 superblock after we modify it, so this just means
calling the lock_buffer() a little earlier.

This checksum corruption problem can be reproduced by xfstests
generic/475.
Reported-by: Nzhangyi (F) <yi.zhang@huawei.com>
Suggested-by: NJan Kara <jack@suse.cz>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b4ff1b44bcd384d22fcbac6ebaf9cc0d33debe50 ]

cgroup_rstat_cpu_pop_updated() is used to traverse the updated cgroups
on flush.  While it was only visiting updated ones in the subtree, it
was visiting @root unconditionally.  We can easily check whether @root
is updated or not by looking at its ->updated_next just as with the
cgroups in the subtree.

* Remove the unnecessary cgroup_parent() test.  The system root cgroup
  is never updated and thus its ->updated_next is always NULL.  No
  need to test whether cgroup_parent() exists in addition to
  ->updated_next.

* Terminate traverse if ->updated_next is NULL.  This can only happen
  for subtree @root and there's no reason to visit it if it's not
  marked updated.

This reduces cpu consumption when reading a lot of rstat backed files.
In a micro benchmark reading stat from ~1600 cgroups, the sys time was
lowered by >40%.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 0d28f49412405d87d3aae83da255070a46e67627 ]

When performing a warm reset in ishtp bus driver, the ishtp_cl_device
will not be removed, its fw_client still points to the already freed
ishtp_device.fw_clients array.

Later after driver finishing ishtp client enumeration, this dangling
pointer may cause driver to bind the wrong ishtp_cl_device to the new
client, causing wrong callback to be called for messages intended for
the new client.

This helps in development of firmware where frequent switching of
firmwares is required without Linux reboot.
Signed-off-by: NHong Liu <hong.liu@intel.com>
Tested-by: NHongyan Song <hongyan.song@intel.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit cc4b1242d7e3b42eed73881fc749944146493e4f ]

The preadv2 and pwritev2 syscalls are supposed to emulate the readv and
writev syscalls when offset == -1. Therefore the compat code should
check for offset before calling do_compat_preadv64 and
do_compat_pwritev64. This is the case for the preadv2 and pwritev2
syscalls, but handling of offset == -1 is missing in their 64-bit
equivalent.

This patch fixes that, calling do_compat_readv and do_compat_writev when
offset == -1. This fixes the following glibc tests on x32:
 - misc/tst-preadvwritev2
 - misc/tst-preadvwritev64v2

Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit fa13e665e02874c0a5f4d06d6967ae34a6cb3d6a ]

If there are exported DMA buffers which are still in use and
grant device is closed by either normal user-space close or by
a signal this leads to the grant device context to be destroyed,
thus making it not possible to correctly destroy those exported
buffers when they are returned back to gntdev and makes the module
crash:

[  339.617540] [<ffff00000854c0d8>] dmabuf_exp_ops_release+0x40/0xa8
[  339.617560] [<ffff00000867a6e8>] dma_buf_release+0x60/0x190
[  339.617577] [<ffff0000082211f0>] __fput+0x88/0x1d0
[  339.617589] [<ffff000008221394>] ____fput+0xc/0x18
[  339.617607] [<ffff0000080ed4e4>] task_work_run+0x9c/0xc0
[  339.617622] [<ffff000008089714>] do_notify_resume+0xfc/0x108

Fix this by referencing gntdev on each DMA buffer export and
unreferencing on buffer release.
Signed-off-by: NOleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Boris Ostrovsky@oracle.com>
Signed-off-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b3098121c42caaf3aea239b8655cf52d45be116f ]

Do not call mt76u_queues_deinit routine in mt76u_alloc_queues error path
since it will be run in mt76x0u_register_device or
mt76x2u_register_device error path. Current implementation triggers the
following kernel warning:

[   67.005516] WARNING: CPU: 2 PID: 761 at lib/refcount.c:187 refcount_sub_and_test_checked+0xa4/0xb8
[   67.019513] refcount_t: underflow; use-after-free.
[   67.099872] Hardware name: BCM2835
[   67.106268] Backtrace:
[   67.111584] [<8010c91c>] (dump_backtrace) from [<8010cc00>] (show_stack+0x20/0x24)
[   67.124974]  r6:60000013 r5:ffffffff r4:00000000 r3:a50bade6
[   67.132226] [<8010cbe0>] (show_stack) from [<807ca5f4>] (dump_stack+0xc8/0x114)
[   67.141225] [<807ca52c>] (dump_stack) from [<8011e65c>] (__warn+0xf4/0x120)
[   67.149849]  r9:000000bb r8:804d0138 r7:00000009 r6:8099dc84 r5:00000000 r4:b66c7b58
[   67.160767] [<8011e568>] (__warn) from [<8011e6d0>] (warn_slowpath_fmt+0x48/0x50)
[   67.171436]  r9:7f65e128 r8:80d1419c r7:80c0bac4 r6:b97b3044 r5:b7368e00 r4:00000000
[   67.182433] [<8011e68c>] (warn_slowpath_fmt) from [<804d0138>] (refcount_sub_and_test_checked+0xa4/0xb8)
[   67.195221]  r3:80c91c25 r2:8099dc94
[   67.200370]  r4:00000000
[   67.204397] [<804d0094>] (refcount_sub_and_test_checked) from [<804d0164>] (refcount_dec_and_test_checked+0x18/0x1c)
[   67.218046]  r4:b7368e00 r3:00000001
[   67.223125] [<804d014c>] (refcount_dec_and_test_checked) from [<805db49c>] (usb_free_urb+0x20/0x4c)
[   67.235358] [<805db47c>] (usb_free_urb) from [<7f639804>] (mt76u_buf_free+0x98/0xac [mt76_usb])
[   67.247302]  r4:00000001 r3:00000001
[   67.252468] [<7f63976c>] (mt76u_buf_free [mt76_usb]) from [<7f639ef8>] (mt76u_queues_deinit+0x44/0x100 [mt76_usb])
[   67.266102]  r8:b8fe8600 r7:b5dac480 r6:b5dace20 r5:00000001 r4:00000000 r3:00000080
[   67.277132] [<7f639eb4>] (mt76u_queues_deinit [mt76_usb]) from [<7f65c040>] (mt76x0u_cleanup+0x40/0x4c [mt76x0u])
[   67.290737]  r7:b5dac480 r6:b8fe8600 r5:ffffffea r4:b5dace20
[   67.298069] [<7f65c000>] (mt76x0u_cleanup [mt76x0u]) from [<7f65c564>] (mt76x0u_probe+0x1f0/0x354 [mt76x0u])
[   67.311174]  r4:b5dace20 r3:00000000
[   67.316312] [<7f65c374>] (mt76x0u_probe [mt76x0u]) from [<805e0b6c>] (usb_probe_interface+0x104/0x240)
[   67.328915]  r7:00000000 r6:7f65e034 r5:b6634800 r4:b8fe8620
[   67.336276] [<805e0a68>] (usb_probe_interface) from [<8056a8bc>] (really_probe+0x224/0x2f8)
[   67.347965]  r10:b65f0a00 r9:00000019 r8:7f65e034 r7:80d3e124 r6:00000000 r5:80d3e120
[   67.359175]  r4:b8fe8620 r3:805e0a68
[   67.364384] [<8056a698>] (really_probe) from [<8056ab60>] (driver_probe_device+0x6c/0x180)
[   67.375974]  r10:b65f0a00 r9:7f65e2c0 r8:b8fe8620 r7:00000000 r6:7f65e034 r5:7f65e034
[   67.387170]  r4:b8fe8620 r3:00000000
[   67.392378] [<8056aaf4>] (driver_probe_device) from [<8056ad54>] (__driver_attach+0xe0/0xe4)
[   67.404097]  r9:7f65e2c0 r8:7f65d22c r7:00000000 r6:b8fe8654 r5:7f65e034 r4:b8fe8620
[   67.415122] [<8056ac74>] (__driver_attach) from [<8056880c>] (bus_for_each_dev+0x68/0xa0)
[   67.426628]  r6:8056ac74 r5:7f65e034 r4:00000000 r3:00000027
[   67.434017] [<805687a4>] (bus_for_each_dev) from [<8056a1cc>] (driver_attach+0x28/0x30)
[   67.445394]  r6:80c6ddc8 r5:b7368f80 r4:7f65e034
[   67.451703] [<8056a1a4>] (driver_attach) from [<80569c24>] (bus_add_driver+0x194/0x21c)
[   67.463081] [<80569a90>] (bus_add_driver) from [<8056b504>] (driver_register+0x8c/0x124)
[   67.474560]  r7:80c6ddc8 r6:7f65e034 r5:00000000 r4:7f65e034
[   67.481964] [<8056b478>] (driver_register) from [<805df510>] (usb_register_driver+0x74/0x140)
[   67.493901]  r5:00000000 r4:7f65e000
[   67.499131] [<805df49c>] (usb_register_driver) from [<7f661024>] (mt76x0_driver_init+0x24/0x1000 [mt76x0u])
[   67.512258]  r9:00000001 r8:7f65e308 r7:00000000 r6:80c08d48 r5:7f661000 r4:7f65e2c0
[   67.523404] [<7f661000>] (mt76x0_driver_init [mt76x0u]) from [<80102f6c>] (do_one_initcall+0x4c/0x210)
[   67.536142] [<80102f20>] (do_one_initcall) from [<801ae63c>] (do_init_module+0x6c/0x21c)
[   67.547639]  r8:7f65e308 r7:80c08d48 r6:b65f0ac0 r5:7f65e2c0 r4:7f65e2c0
[   67.556129] [<801ae5d0>] (do_init_module) from [<801ad68c>] (load_module+0x1d10/0x2304)

Fixes: b40b15e1 ("mt76: add usb support to mt76 layer")
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1b275e4e8b70dbff9850874b30831c1bd8d3c504 ]

Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:

 v4l2_m2m_next_buf
 v4l2_m2m_last_buf
 v4l2_m2m_buf_remove
 v4l2_m2m_next_src_buf
 v4l2_m2m_next_dst_buf
 v4l2_m2m_last_src_buf
 v4l2_m2m_last_dst_buf
 v4l2_m2m_src_buf_remove
 v4l2_m2m_dst_buf_remove

return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.

Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: NEzequiel Garcia <ezequiel@collabora.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8d20dcefe471763f23ad538369ec65b51993ffff ]

Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:

 v4l2_m2m_next_buf
 v4l2_m2m_last_buf
 v4l2_m2m_buf_remove
 v4l2_m2m_next_src_buf
 v4l2_m2m_next_dst_buf
 v4l2_m2m_last_src_buf
 v4l2_m2m_last_dst_buf
 v4l2_m2m_src_buf_remove
 v4l2_m2m_dst_buf_remove

return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.

Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: NEzequiel Garcia <ezequiel@collabora.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 30fa627b32230737bc3f678067e2adfecf956987 ]

Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:

 v4l2_m2m_next_buf
 v4l2_m2m_last_buf
 v4l2_m2m_buf_remove
 v4l2_m2m_next_src_buf
 v4l2_m2m_next_dst_buf
 v4l2_m2m_last_src_buf
 v4l2_m2m_last_dst_buf
 v4l2_m2m_src_buf_remove
 v4l2_m2m_dst_buf_remove

return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.

Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: NEzequiel Garcia <ezequiel@collabora.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit da2d3a4e4adabc6ccfb100bc9abd58ee9cd6c4b7 ]

Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:

 v4l2_m2m_next_buf
 v4l2_m2m_last_buf
 v4l2_m2m_buf_remove
 v4l2_m2m_next_src_buf
 v4l2_m2m_next_dst_buf
 v4l2_m2m_last_src_buf
 v4l2_m2m_last_dst_buf
 v4l2_m2m_src_buf_remove
 v4l2_m2m_dst_buf_remove

return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.

Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: NEzequiel Garcia <ezequiel@collabora.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4a88f89885c7cf65c62793f385261a6e3315178a ]

Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:

 v4l2_m2m_next_buf
 v4l2_m2m_last_buf
 v4l2_m2m_buf_remove
 v4l2_m2m_next_src_buf
 v4l2_m2m_next_dst_buf
 v4l2_m2m_last_src_buf
 v4l2_m2m_last_dst_buf
 v4l2_m2m_src_buf_remove
 v4l2_m2m_dst_buf_remove

return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.

Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: NEzequiel Garcia <ezequiel@collabora.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>