The merge b35c8097 seems to have lost commit eabc4ac5,
put the code back.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This keeps the kernel happy when using edge-irqs and requesting a
threaded irq.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Extract and print info for the new RDL 5, 6, 7 and 8.
Replace const struct with function which translates
the RDL number to string.
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NBarak Bercovitz <barak@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

In addition to existing WCS PLL configuration add and enable
also the coex PLL during init phase. This fixes boot failures
due to silicon latchup in high temperature environment (>85c).
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NNadim Zubidat <nadimz@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Channels 52-64 were mapped incorrectly.

Refactor and document wlcore_get_reg_conf_ch_idx() in
order to make it clear what's going on there.

While on it, fix the return value check to consider
0 as a valid return value as well (indicates channel 1).
Reported-by: NYaniv Machani <yanivma@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

The fw doesn't support channels 7,9,11 in 5ghz band,
so don't advertise supporting them.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

wlvif could be passed as NULL from the wlcore_tx_work_locked()
to the wl1271_prepare_tx_frame() and to wl1271_skb_queue_head()
functions. This may lead to a Kernel panic, fix this by
validating that wlvif != NULL.
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Remove scan debug dumps which are rarely used.
Make scan debug prints more clear and short.
Signed-off-by: NVictor Goldenshtein <victorg@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

We need some stuff done on idle change, most notably we have to stop
sched-scanning. Take care of this by reintroducing idle handling.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

We now disable elp sleep during plt mode to allow normal operation of
plt tools such as calibrator.

Having elp_sleep enabled during plt mode is actually not required and
in fact it disrupt plt operations such as rx statistics etc.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Under this mode the chip is powered on including sdio
but no FW is downloaded and run, interrupts are not enabled, etc...

This mode is intended to allow RTTT to bridge sdio as a transport
to the chip.

Driver only provides sdio access using the dev_mem debugfs file.

Some fixes done to the code that ensures that PLT mode and normal
driver power mode (ifconfig/add_interface) are mutually excluded.
Signed-off-by: NYair Shapira <yair.shapira@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Start a ROC on the AP channel beforing sending the authentication reply
to a connecting STA. This ROC is held up to 1 second via a timer. If the
station is authorized and added by mac80211, the ROC is extended until
the station is fully authorized.
We make sure not to ROC twice when several stations are connecting in
parallel and to only release the ROC when both the pending-reply timer
and the STA-state callbacks do not require it.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Fix RT3070 chip RF initial value to be similar to the latest Ralink vendor
driver.

Tested on Asus N13 usb wifi dongle.
Signed-off-by: NKevin Lo <kevlo@kevlo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the variable continual, and change the while loop
to break when efuse_data == 0xFF.

Tested by compilation only.

CC: Joe Perches <joe@perches.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch brings no functional change.

There are still duplicate macros across the rtlwifi directory, for example
IQK_DELAY_TIME is defined multiple times, sometimes with different values,
this patch only removes duplicates within the same header file.
Signed-off-by: NCatalin Iacob <iacobcatalin@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fast antenna diversity is required only for single chain
chips and the diversity initialization is done in the
per-family board setup routines. Enabling of diversity
should be done based on the calibrated EEPROM/OTP data,
doing it for all chips is incorrect.

Remove the code that sets the fast_div bit for all cards, since
the documentation for the AR_PHY_CCK_DETECT register says:

reg 642: sig_detect_cck
enable_ant_fast_div : Only used for single chain chips.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a FATAL interrupt is received, a full chip reset is
required, which is done in the main tasklet. But since
the reset routine is scheduled as a work item, make sure
that interrupts are not enabled in the tasklet before the
reset is done.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rather than using the chip ID to read only chain-0 CCA
registers and avoid reading chain-1, use the RX chainmask
instead. There are some 1-stream PCI devices based on AR9287
such as TL-WN751ND. Improper NF calibration might result in
DMA errors/timeouts.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove routine _rtl92c_process_phyinfo() by using the equivalent routine
in driver rtlwifi.

This change also allows the removal of 5 additional routines from rtl8192cu.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The other structures in wmi.h are already marked this way.
Without this marking, we get an unaliged access panic in the tilegx kernel:

Starting stack dump of tid 0, pid 0 (swapper) on cpu 35 at cycle 198675113844
  frame 0: 0xfffffff7103ada90 ath9k_htc_swba+0x120/0x618 [ath9k_htc]
  frame 1: 0xfffffff7103a4b10 ath9k_wmi_event_tasklet+0x1b0/0x270 [ath9k_htc]
  frame 2: 0xfffffff700326570 tasklet_action+0x148/0x298
  [...]
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The band selection and PE control code for the
RT3593 chipsets only handles USB based devices
currently. Due to this limitation RT3593 based
PCIe cards are not working correctly.

On PCIe cards band selection is controlled via
GPIO #8 which is identical to the USB devices.
The LNA PE control is slightly different, all
LNA PEs are controlled by GPIO #4.

Update the code to configure the GPIO_CTRL register
correctly on PCIe devices.

Cc: Steven Liu <steven.liu@mediatek.com>
Cc: JasonYS Cheng <jasonys.cheng@mediatek.com>
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since HW PeakDetect calibration is turned on for AR9462,
various conditions have to be handled in the driver:

* Enable agc_cal when loading RTT fails.
* Disable SW PeakDetect calibration when RTT calibration is not enabled.
* Keep SW PeakDetect calibration result in driver.
* Update RTT table according to the saved value.
* Write RTT back after modifying SW RTT table.
* Enable local mode for PeakDetect calibration and restore values.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Beacon transmission would get stuck if the NAV is
an invalid value for some reason. Check and correct
the NAV value in the HW when this happens.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All QCA chips have the ability to parse the CF Parameter Set
IE in beacons. If the IE is malformed in the beacons from some
APs [1], the HW locks up. In AP mode, a beacon stuck would happen
and in client mode, a disconnection usually is the result.

To fix this issue, set the AR_PCU_MISC_MODE2_CFP_IGNORE to ignore
the CFP IE in beacons - this is applicable for all chips. For
AP mode, if this issue happens, the NAV is also corrupted and has
to be reset - this will be done in a subsequent patch.

[1] : http://msujith.org/ath9k/cfp/Malformed-CF-Param.pngSigned-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX IQ calibration is disabled by default for AR9462, this
is done using the initvals (reg 0xa644).

But, to compensate for this, the AR_PHY_RX_DELAY register
should be set to the max allowed value when performing
calibration.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>