This implements suspend and resume callbacks for the macb driver. We may
have to do some more to gracefully shut the MAC down, but this at least
prevents the macb from waking the system when hooked up to a busy
network.
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Patrice Vilchez <patrice.vilchez@rfo.atmel.com>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>

Fix warning:
drivers/net/pppoe.c: In function 'pppoe_recvmsg':
drivers/net/pppoe.c:945: warning: comparison of distinct pointer types lacks a cast
because skb->len is unsigned int and total_len is size_t
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, tun.c running in TUN_TUN_DEV mode will set the protocol of
packet to IPv4 if TUN_NO_PI is set. My program failed to work when I
assumed that the driver will check the first nibble of packet,
determine IP version and set the appropriate protocol.
Signed-off-by: NAng Way Chuang <wcang@nav6.org>
Acked-by: NMax Krasnyansky <maxk@qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The atl1 driver tries to determine the MAC address thusly:

	- If an EEPROM exists, read the MAC address from EEPROM and
	  validate it.
	- If an EEPROM doesn't exist, try to read a MAC address from
	  SPI flash.
	- If that fails, try to read a MAC address directly from the
	  MAC Station Address register.
	- If that fails, assign a random MAC address provided by the
	  kernel.

We now have a report of a system fitted with an EEPROM containing all
zeros where we expect the MAC address to be, and we currently handle
this as an error condition.  Turns out, on this system the BIOS writes
a valid MAC address to the NIC's MAC Station Address register, but we
never try to read it because we return an error when we find the all-
zeros address in EEPROM.

This patch relaxes the error check and continues looking for a MAC
address even if it finds an illegal one in EEPROM.
Signed-off-by: NRadu Cristescu <advantis@gmx.net>
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Keep enc28j60 chips in low-power mode when they're not in use.
At typically 120 mA, these chips run hot even when idle; this
low power mode cuts that power usage by a factor of around 100.

This version provides a generic routine to poll a register until
its masked value equals some value ... e.g. bit set or cleared.
It's basically what the previous wait_phy_ready() did, but this
version is generalized to support the handshaking needed to
enter and exit low power mode.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NClaudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Minor bugfixes to the enc28j60 driver ... wrong section marking,
indentation, and bogus use of spi_bus_type.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NClaudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Missed one pci id for 88E8040T.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Downloading firmware in pci probe allows recovery in case of
firmware failure by reloading the driver.

Also reduced delays in firmware load.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

o Remove unnecessary debug prints and functions.
o Explicitly specify pci class (0x020000) to avoid enabling
  management function.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Store physical port number in netxen_adapter structure.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This fixes a the issue where logical port number is set incorrectly
for HP blade mezz cards.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The ibm_newemac driver requires ether_crc to be defined.  Apparently it is
possible to generate a .config without CONFIG_CRC32 set which causes the
following link errors if IBM_NEW_EMAC is selected:

  LD      .tmp_vmlinux1
drivers/built-in.o: In function `emac_hash_mc':
core.c:(.text+0x2f524): undefined reference to `crc32_le'
core.c:(.text+0x2f528): undefined reference to `bitrev32'
make: *** [.tmp_vmlinux1] Error 1

This patch has IBM_NEW_EMAC select CRC32 so we don't hit this error.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add new rt73usb USB ID for D-Link DWA111
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Config symbols that select LEDS_CLASS need to depend on NEW_LEDS so that
undefined symbols are not used in the build.

The alternative is to select NEW_LEDS, which some drivers do.

This patch fixes the led_* symbols build errors.

(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Config symbols that select RFKILL need to depend on INPUT so that
undefined symbols are not used in the build.

This patch fixes the input_* symbols build errors.

(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes a WARN_ON that is responsible for the following koops:
http://www.kerneloops.org/searchweek.php?search=b43_generate_noise_sample

The comment in the patch describes why it's safe to simply remove
the check.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a possible NULL pointer dereference in an error path of the
DMA allocation error checking code. This is also necessary for a future
DMA API change that is on its way into the mainline kernel that adds
an additional dev parameter to dma_mapping_error().

This patch moves the whole struct b43_dmaring struct initialization
right before any DMA allocation operation.
Reported-by: NMiles Lane <miles.lane@gmail.com>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

None of the rt2x00 PCI devices support 64-bit DMA addresses (they all
only accept 32-bit buffer addresses). Hence it makes no sense to try to
enable 64-bit DMA addresses. Only try to enable 32-bit DMA addresses.
Signed-off-by: NGertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a "BUG: unable to handle kernel paging request"
bug in rt73usb which was caused by killing the guardian_urb
while it had never been allocated for rt73usb.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I would like to thank Eliezer Tamir for writing and maintaining the
driver for the past two years. I will take over maintaining the bnx2x
driver from now on.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the RTNL is held when we invoke flush_scheduled_work() we could
deadlock.  One such case is linkwatch, it is a work struct which tries
to grab the RTNL semaphore.

The most common case are net driver ->stop() methods.  The
simplest conversion is to instead use cancel_{delayed_}work_sync()
explicitly on the various work struct the driver uses.

This is an OK transformation because these work structs are doing
things like resetting the chip, restarting link negotiation, and so
forth.  And if we're bringing down the device, we're about to turn the
chip off and reset it anways.  So if we cancel a pending work event,
that's fine here.

Some drivers were working around this deadlock by using a msleep()
polling loop of some sort, and those cases are converted to instead
use cancel_{delayed_}work_sync() as well.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compared to other places in the kernel, I think that this driver misuses
the function round_jiffies.
Signed-off-by: NChristophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Duplicate NETIF_MSG_IFDOWN, 2nd should be NETIF_MSG_IFUP
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NSylvain Munaut <tnt@246tNt.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The branches are dead code.  even when dev->flag IFF_MULTICAST (defined
0x1000) is set, dev->flags & IFF_MULTICAST & [boolean] always evaluates to
0.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

dev_close() must be called holding the RTNL.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Using vendor magic to force the PHY into power save mode breaks
suspend.  It isn't needed anyway, so remove it.
Tested-by: NAvuton Olrich <avuton@gmail.com>
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

virtio_net uses a timer to free old transmitted packets, rather than
leaving callbacks enabled all the time.  If the host promises to
always notify us when the transmit ring is empty, we can free packets
at that point and avoid the timer.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

virtio_net currently only frees old transmit skbs just
before queueing new ones. If the queue is full, it then
enables interrupts and waits for notification that more
work has been performed.

However, a side-effect of this scheme is that there are
always xmit skbs left dangling when no new packets are
sent, against the Documentation/networking/driver.txt
guideline:

  "... it is not allowed for your TX mitigation scheme
   to let TX packets "hang out" in the TX ring unreclaimed
   forever if no new TX packets are sent."

Add a timer to ensure that any time we queue new TX
skbs, we will shortly free them again.

This fixes an easily reproduced hang at shutdown where
iptables attempts to unload nf_conntrack and nf_conntrack
waits for an skb it is tracking to be freed, but virtio_net
never frees it.
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

hdr->csum_start is the offset from the start of the ethernet
header to the transport layer checksum field. skb->csum_start
is the offset from skb->head.

skb_partial_csum_set() assumes that skb->data points to the
ethernet header - i.e. it computes skb->csum_start by adding
the headroom to hdr->csum_start.

Since eth_type_trans() skb_pull()s the ethernet header,
skb_partial_csum_set() should be called before
eth_type_trans().

(Without this patch, GSO packets from a guest to the world outside the
host are corrupted).
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

eHEA has to call firmware functions in order to change the mac address
of a logical port. This patch checks if the logical port is up
when calling the register / deregister mac address calls. If the port
is down these firmware calls would fail and are therefore not executed.
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

RX queue flush can fail if traffic continues to arrive.  Recover by
performing an invisible reset.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch fixes the following build error:

<--  snip  -->

...
  Building modules, stage 2.
  MODPOST 1203 modules
ERROR: "lance_open" [drivers/net/mvme147.ko] undefined!
ERROR: "lance_close" [drivers/net/mvme147.ko] undefined!
ERROR: "lance_tx_timeout" [drivers/net/mvme147.ko] undefined!
ERROR: "lance_set_multicast" [drivers/net/mvme147.ko] undefined!
ERROR: "lance_start_xmit" [drivers/net/mvme147.ko] undefined!
...
make[2]: *** [__modpost] Error 1

<--  snip  -->
Reported-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Define names were accidently transposed.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add a workaround for lost MSI interrupts.  There is a race condition in
the HW in which future interrupts could be missed.  The workaround is to
toggle the MSI irq mask.

Added cleanup based on comments from Andrew Morton.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We need to unshare the skb first as otherwise pskb_may_pull may
write to a shared skb which could be bad.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The length field in the PPPOE header wasn't checked completely.
This patch causes all packets shorter than the declared length
to be dropped.

It also changes the memcpy_toiovec call to skb_copy_datagram_iovec
so that paged packets (rare for PPPOE) are handled properly.

Thanks to Ilja of the Netric Security Team for discovering and
reporting this bug, and Chris Wright for the total_len check.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a potential memory corruption in
pppol2tp_recvmsg(). If skb->len is bigger than the caller's buffer
length, memcpy_toiovec() will go into unintialized data on the kernel
heap, interpret it as an iovec and start modifying memory.

The fix is to change the memcpy_toiovec() call to
skb_copy_datagram_iovec() so that paged packets (rare for PPPOL2TP)
are handled properly. Also check that the caller's buffer is big
enough for the data and set the MSG_TRUNC flag if it is not so.
Reported-by: NIlja <ilja@netric.org>
Signed-off-by: NJames Chapman <jchapman@katalix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

-tip testing found the following build error:

  drivers/built-in.o: In function `mcs_receive_irq':
  mcs7780.c:(.text+0x4e429): undefined reference to `crc32_le'
  drivers/built-in.o: In function `mcs_hard_xmit':
  mcs7780.c:(.text+0x4e9af): undefined reference to `crc32_le'

with:

  http://redhat.com/~mingo/misc/config-Sun_Jun__8_22_56_14_CEST_2008.bad

the reason is a missing enablement of the CRC32 library in the Kconfig.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>