Drop the vendor-prefix from the "ti,system-power-controller" device-tree
property name.

It has been agreed to make "system-power-controller" a standard property
and to drop the vendor-prefix that is currently used by several drivers.

Note that drivers that have used "<vendor>,system-power-controller" in a
released kernel will need to support both versions.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Configure the RTC as system-power controller, which allows the system to
be powered off as well as woken up again on subsequent RTC alarms.

Note that the PMIC needs to be put in SLEEP (rather than OFF) mode to
maintain RTC power.  Specifically, this means that the PMIC
ti,pmic-shutdown-controller property must be left unset in order to be
able to wake up on RTC alarms.

Tested on BeagleBone Black (rev A5).
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable am33xx specific RTC features (e.g. PMIC control) by adding
"ti,am3352-rtc" to the compatible property of the rtc node.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This will enable use of physical arch timers on rk3288, where each
core comes out of reset with a different virtual offset.  Using
physical timers will help with SMP booting on coreboot and older
u-boot and should also allow suspend-resume and cpu-hotplug to work on
all firmwares.

Firmware which does initialize the cpu registers properly at boot and
cpu-hotplug can remove this property from the device tree.
Signed-off-by: NSonny Rao <sonnyrao@chromium.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Many of AM335x and AM437x hook backlight to
one of these two devices. By enabling their
drivers we make sure pwm-backlight can do
its thing.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

AM437x devices have a DWC3 IP inside of them.

The host side implementation of DWC3 is XHCI
compliant. By enabling XHCI driver, we get
the USB host port on AM437x Starter Kit working
out of the box.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Without this, sound on AM437x Starter Kit will
not work.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

AM437x Starter Kit ships with EDT FT5306 touchscreen
device. By enabling the driver we make sure touchscreen
will work out of the box.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

None of these drivers are known to be used on
any platform supported by omap2plus_defconfig,
by removing them we get a slight smaller kernel.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

We now have the physical-timers patches lined up as a dependency in this same
branch, so we can revert the temporary disablement.

This reverts commit b77d4394.
Signed-off-by: NOlof Johansson <olof@lixom.net>

This is a bug fix for using physical arch timers when
the arch_timer_use_virtual boolean is false.  It restores the
arch_counter_get_cntpct() function after removal in

0d651e4e "clocksource: arch_timer: use virtual counters"

We need this on certain ARMv7 systems which are architected like this:

* The firmware doesn't know and doesn't care about hypervisor mode and
  we don't want to add the complexity of hypervisor there.

* The firmware isn't involved in SMP bringup or resume.

* The ARCH timer come up with an uninitialized offset between the
  virtual and physical counters.  Each core gets a different random
  offset.

* The device boots in "Secure SVC" mode.

* Nothing has touched the reset value of CNTHCTL.PL1PCEN or
  CNTHCTL.PL1PCTEN (both default to 1 at reset)

One example of such as system is RK3288 where it is much simpler to
use the physical counter since there's nobody managing the offset and
each time a core goes down and comes back up it will get reinitialized
to some other random value.

Fixes: 0d651e4e ("clocksource: arch_timer: use virtual counters")
Cc: stable@vger.kernel.org
Signed-off-by: NSonny Rao <sonnyrao@chromium.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The imx6 PM code seems to be quite creative in its use of irq_data,
using something that is very much a hardware interrupt number where
we expect a virtual one.  Yes, it worked so far, but that's only
luck, and it will definitely explode in 3.19.

Fix it by using a pair of helper functions that deal with the
actual hardware.
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

mach-imx directly references to the irq field in
struct irq_data, and uses this to directly poke hardware register.

But irq is the *virtual* irq number, something that has nothing
to do with the actual HW irq (stored in the hwirq field). And once
we put the stacked domain code in action, the whole thing explodes,
as these two values are *very* different.

Just replacing all instances of irq with hwirq fixes the issue.
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch enables the MAX77686 PMIC drivers in the multi_v7_defconfig used
on exynos4412-prime family of SoCs [1]. The exynos4412-prime based boards
are producing the following runtime errors only on the multi_v7_defconfig [2]:

kern.err: deviceless supply vdd_arm not found, using dummy regulator
kern.err: exynos-cpufreq exynos-cpufreq: failed to set cpu voltage to 1287500
kern.err: cpufreq: __target_index: Failed to change cpu frequency: -22

I reviewed the exynos_defconfig, which does not produce these runtime
errors. It was obvious that the exynos_defconfig has the PMIC drivers
enabled, whereas the multi_v7_defconfig does not. This patch has been tested
on a odroid-u2 and a odroid-u3 board. It has resolved the runtime errors.
Therefore, I purpose we enabled these drivers in the multi_v7_defconfig.

[1] http://www.hardkernel.com/main/products/prdt_info.php?g_code=G135270682824
[2] http://storage.armcloud.us/kernel-ci/mainline/v3.18-rc7-48-g7cc78f8/arm-multi_v7_defconfig/lab-tbaker-00/boot-exynos4412-odroidu3.htmlSigned-off-by: NTyler Baker <tyler.baker@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

This chip is present on at91sam9261ek board: add it to the at91_dt_defconfig.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

As this touch button driver is used on at91sam9x5ek, it's better to enable it.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This is the selection of the new PWM driver using TC Blocks. This driver is
useful so we enable it in both sama5 and at91_dt defconfig files.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add the Atmel eXtended DMA Controller driver option. This driver is first used
on SAMA5D4 SoCs and only relevant in sama5_defconfig file.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add neon support for sama5d4 and large blocks/files support.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This commit adjusts the registration of the cpufreq-dt driver in the
mvebu platform to indicate to the cpufreq driver that the platform has
independent clocks for each CPU.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This is a squash of several imx_v6_v7_defconfig update patches.

 - Enable tlv320aic3x audio codec by default (Phytec PBAB01 board)
 - Enable DS1307 rtc and gpio fan by default (TBS2910 board)
 - Select thermal related drivers
 - Add SNVS power off driver
Signed-off-by: NDmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: NSoeren Moch <smoch@web.de>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NRobin Gong <b38343@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Instead of using the dev_ops ->stop|start() callbacks for genpd, let's
convert to use genpd's flag field and set it to GENPD_FLAG_PM_CLK.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Tested-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Instead of using the dev_ops ->stop|start() callbacks for genpd, let's
convert to use genpd's flag field and set it to GENPD_FLAG_PM_CLK.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

All functions declared in this file are gone.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
[nicolas.ferre@atmel.com: re-order patches so modify board-dt-sam9]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

These files were left behind with no reason. Remove them.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

As AT91 !DT code is now removed, cleanup the PIT clocksource driver.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
[nicolas.ferre@atmel.com: split patch]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>

vsys is the core always-on supply of the Marsboard.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

As at91rm9200 is now DT only, there is no need to keep old entry point in this
at91rm9200 System Timer (ST) driver.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
[nicolas.ferre@atmel.com: split patch]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

GPIO and LED drivers were replaced by generic ones for DT boards. These drivers
were remaining: delete them now. Modifications are also done on the
corresponding header files.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
[nicolas.ferre@atmel.com: split patch]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The AT91-specific SoC strucutre "struct at91_init_soc" was filled with specific
!DT initilisation functions. Now that we got rid of the !DT board file
description, remove unneeded functions.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
[nicolas.ferre@atmel.com: split patch]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

An explicit selection option is not needed for board files so now we select the
board from SoC option.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
[nicolas.ferre@atmel.com: remove option's comments; split patch]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

IRQ support for Broadcom's bus-axi driver bcma was merged into John
Linville's wireless tree and will show up in 3.19. This patch makes use
of this feature in the DTS file for the the BCM5301X SoCs. I left the
PCIe controller out, because this still needs some discussion.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>

secondary_startup() in the header is not needed at all.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add a DTS describing the Digilent ZYBO board. Similar to ZED but with
a 50MHz crystal instead of 33MHz.
Acked-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The fact that all supported boards use the same 33MHz crystal is a
co-incidence. The Zynq PS support a range of crystal freqs so the
hardcoded setting should be removed from the dtsi. Re-implement it
on the board level.

This prepares support for Zynq boards with different crystal
frequencies (e.g. the Digilent ZYBO).
Acked-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NPeter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>