When enabling the hwtstamp mode for Rx timestamping the V2 ptp event type
specific modes (Delay Request and Sync) have been rolled into the V2 all event
packet modes, in order to more accurately represent what hardware is doing.
Hardware always timestamps the Path delay packets when a V2 mode is selected,
regardless of what type was selected (in order to always support Path delay
mode). However this means the user selected modes of timestamping only Sync or
Delay Request is not truly supported. This patch correctly sets the mode for
the hwtstamp config and returns to the user that all V2 event packets will be
timestamped.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes two minor nits from Richard Cochran. The first is a case of
ambitious line wrapping that wasn't necessary. The second is to re-order the
flag checks for PPS support. Previously, the hardware test was done first, and
the interrupt flag test was done second. Now, test the interrupt flag and use
the unlikely macro.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe_sysfs.c is only needed when CONFIG_IXGBE_HWMON is configured in the
kernel.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Acked-by: NDon Skidmore <Donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The flow control DV macros are used to calculate the flow control
high and low thresholds. This patch annotates these macros slightly
better and fixes the issues below.

The macro variables are renamed LINK to _max_frame_link and TC to
_max_frame_tc. This was to avoid confusion and make them more
readable. It was found that people auditing the code read TC to be
'traffic class' in the 802.1Q definition instead of the max frame
size of the tc. Hopefully it is clear now.

This audit also found the following real deviations from the
theoretical values. Fixed in this patch.

  * I multiplied the DV calculations by (36/25) which always
    evaluates to 1. This does not match the intended theoretical
    value of 1.44.

  * IXGBE_BT2KB added 1023 to account for rounding however this
    really should be 8 * 1023 - 1 to account for division by 8k.

  * x2 multiplication of max frame in DV calculations to account
    for updated hardware recommendations.

With this patch the DV values are inline with the recommendations
in the 82599 and 82598 data sheets. Its worth noting I did not
see any dropped frames with flow control on in my experiments without
this patch. However aligning with the hardware specs and
recommendations seems like a good idea here to account for worst
case scenarios.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a report from Ethan Zhao, before calling register_netdev() the
driver should be using logging macros that do not display the potentially
confusing "(unregistered net_device)" yet still display the useful driver
name and PCI bus/device/function.
Reported-by: NEthan Zhao <ethan.kernel@gmail.com>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When packets are dropped in TX path, its better to use kfree_skb()
instead of dev_kfree_skb() to give proper drop_monitor events.

Also move the kfree_skb() call after read_unlock() in bond_alb_xmit()
and bond_xmit_activebackup()
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EMSGSIZE - ran out of space while constructing message
EOPNOTSUPP - driver/hardware does not support operation
ENODEV - network device not found
EINVAL - invalid message
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocating and sending the skb in dcb_doit() allows for much
shorter and cleaner command handling functions.

The huge switch statement is replaced with an array based definition
of the handling function and reply message type.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to allocate and send the reply message in each
handling function separately. Instead, the reply skb can be allocated
and sent in dcb_doit() directly.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	MAINTAINERS
	drivers/net/wireless/iwlwifi/pcie/trans.c

The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.

The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'Get' commands should generally not require CAP_NET_ADMIN, with
the exception of those that expose internal state.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add dev_loopback_xmit() in order to deduplicate functions
ip_dev_loopback_xmit() (in net/ipv4/ip_output.c) and
ip6_dev_loopback_xmit() (in net/ipv6/ip6_output.c).

I was about to reinvent the wheel when I noticed that
ip_dev_loopback_xmit() and ip6_dev_loopback_xmit() do exactly what I
need and are not IP-only functions, but they were not available to reuse
elsewhere.

ip6_dev_loopback_xmit() does not have line "skb_dst_force(skb);", but I
understand that this is harmless, and should be in dev_loopback_xmit().
Signed-off-by: NMichel Machado <michel@digirati.com.br>
CC: "David S. Miller" <davem@davemloft.net>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jpirko@redhat.com>
CC: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cloning all packets in input path have a significant cost.

Use skb_header_pointer()/skb_copy_bits() instead of pskb_may_pull() so
that recv_probe handlers (bond_3ad_lacpdu_recv / bond_arp_rcv /
rlb_arp_recv ) dont touch input skb.

bond_handle_frame() can avoid the skb_clone()/dev_kfree_skb()
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Jiri Bohac <jbohac@suse.cz>
Cc: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Cc: Maciej Żenczykowski <maze@google.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The line below in intr_complete isn't needed,

	memset(urb->transfer_buffer, 0, urb->transfer_buffer_length);

so just remove it.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove declaration for intr_complete so that ctags may be happy to
decrease duplicated symbols, also decrease one line code.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flag of EVENT_DEV_WAKING is not used any more, so just remove it.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

usb_device is parent device of usb_interface in the view of driver
model, so its reference count is always held during .probe/.disconnect
of usb_interface instance.

This patch just removes the unnecessay usb_get/put_dev.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

usb_device is parent device of usb_interface in the view of driver
model, so its reference count is always held during .probe/.disconnect
of usb_interface instance.

This patch just removes the unnecessay usb_get/put_dev.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

usb_device is parent device of usb_interface in the view of driver
model, so its reference count is always held during .probe/.disconnect
of usb_interface instance.

This patch just removes the unnecessay usb_get/put_dev.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the transmit path of the bonding driver, skb->cb is used to
stash the skb->queue_mapping so that the bonding device can set its
own queue mapping.  This value becomes corrupted since the skb->cb is
also used in __dev_xmit_skb.

When transmitting through bonding driver, bond_select_queue is
called from dev_queue_xmit.  In bond_select_queue the original
skb->queue_mapping is copied into skb->cb (via bond_queue_mapping)
and skb->queue_mapping is overwritten with the bond driver queue.

Subsequently in dev_queue_xmit, __dev_xmit_skb is called which writes
the packet length into skb->cb, thereby overwriting the stashed
queue mappping.  In bond_dev_queue_xmit (called from hard_start_xmit),
the queue mapping for the skb is set to the stashed value which is now
the skb length and hence is an invalid queue for the slave device.

If we want to save skb->queue_mapping into skb->cb[], best place is to
add a field in struct qdisc_skb_cb, to make sure it wont conflict with
other layers (eg : Qdiscc, Infiniband...)

This patchs also makes sure (struct qdisc_skb_cb)->data is aligned on 8
bytes :

netem qdisc for example assumes it can store an u64 in it, without
misalignment penalty.

Note : we only have 20 bytes left in (struct qdisc_skb_cb)->data[].
The largest user is CHOKe and it fills it.

Based on a previous patch from Tom Herbert.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NTom Herbert <therbert@google.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Routing of 127/8 is tradtionally forbidden, we consider
packets from that address block martian when routing and do
not process corresponding ARP requests.

This is a sane default but renders a huge address space
practically unuseable.

The RFC states that no address within the 127/8 block should
ever appear on any network anywhere but it does not forbid
the use of such addresses outside of the loopback device in
particular. For example to address a pool of virtual guests
behind a load balancer.

This patch adds a new interface option 'route_localnet'
enabling routing of the 127/8 address block and processing
of ARP requests on a specific interface.

Note that for the feature to work, the default local route
covering 127/8 dev lo needs to be removed.

Example:
  $ sysctl -w net.ipv4.conf.eth0.route_localnet=1
  $ ip route del 127.0.0.0/8 dev lo table local
  $ ip addr add 127.1.0.1/16 dev eth0
  $ ip route flush cache

V2: Fix invalid check to auto flush cache (thanks davem)
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we modify primary via sysfs and it is not a valid slave,
we should record it for future use, and this behavior is the same with
bond_check_params().
Signed-off-by: NWeiping Pan <wpan@redhat.com>
Acked-by: NNicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

This change adds support for the tilegx network driver based on the
GXIO IORPC support in the tilegx software stack, using the on-chip
mPIPE packet processing engine.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more current logging style.

Add pr_fmt and missing newlines.
Remove embedded prefixes.
Neaten phy_print_status to avoid using KERN_CONT.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

5906 devices also need the short DMA fragment workaround.  This patch
makes the necessary change.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Tested-by: NChristian Kujau <lists@nerdbynature.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This small patch removes access to the last element of the spkt_device
array through a constant. Instead, it is accessed by sizeof() to respect
possible changes in if_packet.h.
Signed-off-by: NDaniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clk_{un}prepare is mandatory for platforms using common clock framework.
Since these drivers are used by SPEAr platform, which supports common
clock framework, add clk_{un}prepare() support for them. Otherwise
the clocks are not correctly en-/disabled and ethernet support doesn't
work.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no peer actually gets attached (either because create is zero or
the peer allocation fails) we'll trigger a BUG because we
unconditionally do an rt{,6}_peer_ptr() afterwards.

Fix this by guarding it with the proper check.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the compilation of the TCP and UDP trackers with sysctl
compilation disabled:

net/netfilter/nf_conntrack_proto_udp.c: In function ‘udp_init_net_data’:
net/netfilter/nf_conntrack_proto_udp.c:279:13: error: ‘struct nf_proto_net’ has no member named
 ‘user’
net/netfilter/nf_conntrack_proto_tcp.c:1606:9: error: ‘struct nf_proto_net’ has no member named
 ‘user’
net/netfilter/nf_conntrack_proto_tcp.c:1643:9: error: ‘struct nf_proto_net’ has no member named
 ‘user’
Reported-by: NFengguang Wu <wfg@linux.intel.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__lpc_handle_xmit() has two bugs :

1) It can leak skbs in case TXSTATUS_ERROR is set

2) It can wake up txqueue while no slot was freed.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NRoland Stigge <stigge@antcom.de>
Tested-by: NRoland Stigge <stigge@antcom.de>
Cc: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lpc_eth does a copy of transmitted skbs to DMA area, without checking
skb lengths, so can trigger buffer overflows :

memcpy(pldat->tx_buff_v + txidx * ENET_MAXF_SIZE, skb->data, len);

One way to get bigger skbs is to allow MTU changes above the 1500 limit.

Calling eth_change_mtu() in ndo_change_mtu() makes sure this cannot
happen.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Roland Stigge <stigge@antcom.de>
Cc: Kevin Wells <kevin.wells@nxp.com>
Acked-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__dev_get_by_name() is slow because pm_qos_req has been inserted between
name[] and name_hlist, adding cache misses.

pm_qos_req has nothing to do at the beginning of struct net_device
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>