Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 161
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 24 4月, 2017 2 次提交
    • J
      Update ABORT processing for NVMET. · 86c67379
      由 James Smart 提交于 
      The driver with nvme had this routine stubbed.

Right now XRI_ABORTED_CQE is not handled and the FC NVMET
Transport has a new API for the driver.

Missing code path, new NVME abort API
Update ABORT processing for NVMET

There are 3 new FC NVMET Transport API/ template routines for NVMET:

lpfc_nvmet_xmt_fcp_release
This NVMET template callback routine called to release context
associated with an IO This routine is ALWAYS called last, even
if the IO was aborted or completed in error.

lpfc_nvmet_xmt_fcp_abort
This NVMET template callback routine called to abort an exchange that
has an IO in progress

nvmet_fc_rcv_fcp_req
When the lpfc driver receives an ABTS, this NVME FC transport layer
callback routine is called. For this case there are 2 paths thru the
driver: the driver either has an outstanding exchange / context for the
XRI to be aborted or not.  If not, a BA_RJT is issued otherwise a BA_ACC

NVMET Driver abort paths:

There are 2 paths for aborting an IO. The first one is we receive an IO and
decide not to process it because of lack of resources. An unsolicated ABTS
is immediately sent back to the initiator as a response.
lpfc_nvmet_unsol_fcp_buffer
            lpfc_nvmet_unsol_issue_abort  (XMIT_SEQUENCE_WQE)

The second one is we sent the IO up to the NVMET transport layer to
process, and for some reason the NVME Transport layer decided to abort the
IO before it completes all its phases. For this case there are 2 paths
thru the driver:
the driver either has an outstanding TSEND/TRECEIVE/TRSP WQE or no
outstanding WQEs are present for the exchange / context.
lpfc_nvmet_xmt_fcp_abort
    if (LPFC_NVMET_IO_INP)
        lpfc_nvmet_sol_fcp_issue_abort  (ABORT_WQE)
                lpfc_nvmet_sol_fcp_abort_cmp
    else
        lpfc_nvmet_unsol_fcp_issue_abort
                lpfc_nvmet_unsol_issue_abort  (XMIT_SEQUENCE_WQE)
                        lpfc_nvmet_unsol_fcp_abort_cmp

Context flags:
LPFC_NVMET_IOP - his flag signifies an IO is in progress on the exchange.
LPFC_NVMET_XBUSY  - this flag indicates the IO completed but the firmware
is still busy with the corresponding exchange. The exchange should not be
reused until after a XRI_ABORTED_CQE is received for that exchange.
LPFC_NVMET_ABORT_OP - this flag signifies an ABORT_WQE was issued on the
exchange.
LPFC_NVMET_CTX_RLS  - this flag signifies a context free was requested,
but we are deferring it due to an XBUSY or ABORT in progress.

A ctxlock is added to the context structure that is used whenever these
flags are set/read  within the context of an IO.
The LPFC_NVMET_CTX_RLS flag is only set in the defer_relase routine when
the transport has resolved all IO associated with the buffer. The flag is
cleared when the CTX is associated with a new IO.

An exchange can has both an LPFC_NVMET_XBUSY and a LPFC_NVMET_ABORT_OP
condition active simultaneously. Both conditions must complete before the
exchange is freed.
When the abort callback (lpfc_nvmet_xmt_fcp_abort) is envoked:
If there is an outstanding IO, the driver will issue an ABORT_WQE. This
should result in 3 completions for the exchange:
1) IO cmpl with XB bit set
2) Abort WQE cmpl
3) XRI_ABORTED_CQE cmpl
For this scenerio, after completion #1, the NVMET Transport IO rsp
callback is called.  After completion #2, no action is taken with respect
to the exchange / context.  After completion #3, the exchange context is
free for re-use on another IO.

If there is no outstanding activity on the exchange, the driver will send a
ABTS to the Initiator. Upon completion of this WQE, the exchange / context
is freed for re-use on another IO.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
      86c67379
    • J
      Fix crash after issuing lip reset · 9d3d340d
      由 James Smart 提交于 
      When RPI is not available, driver sends WQE with invalid RPI value and
rejected by HBA.
lpfc 0000:82:00.3: 1:3154 BLS ABORT RSP failed, data:  x3/xa0320008
and
lpfc :2753 PLOGI failure DID:FFFFFA Status:x3/xa0240008

In this case, driver accesses rpi_ids array out of bounds.

Fix:
Check return value of lpfc_sli4_alloc_rpi(). Do not allocate
lpfc_nodelist entry if RPI is not available.

When RPI is not available, we will get discovery timeouts and
command drops for some of the vports as seen below.

lpfc :0273 Unexpected discovery timeout, vport State x0
lpfc :0230 Unexpected timeout, hba link state x5
lpfc :0111 Dropping received ELS cmd Data: x0 xc90c55 x0
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
      9d3d340d
  3. 07 3月, 2017 1 次提交
    • J
      scsi: lpfc: Fix eh_deadline setting for sli3 adapters. · 96418b5e
      由 James Smart 提交于 
      A previous change unilaterally removed the hba reset entry point
from the sli3 host template. This was done to allow tape devices
being used for back up from being removed. Why was this done ?
When there was non-responding device on the fabric, the error
escalation policy would escalate to the reset handler. When the
reset handler was called, it would reset the adapter, dropping
link, thus logging out and terminating all i/o's - on any target.
If there was a tape device on the same adapter that wasn't in
error, it would kill the tape i/o's, effectively killing the
tape device state.  With the reset point removed, the adapter
reset avoided the fabric logout, allowing the other devices to
continue to operate unaffected. A hack - yes. Hint: we really
need a transport I_T nexus reset callback added to the eh process
(in between the SCSI target reset and hba reset points), so a
fc logout could occur to the one bad target only and stop the error
escalation process.

This patch commonizes the approach so it can be used for sli3 and sli4
adapters, but mandates the admin, via module parameter, specifically
identify which adapters the resets are to be removed for. Additionally,
bus_reset, which sends Target Reset TMFs to all targets, is also removed
from the template as it too has the same effect as the adapter reset.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NLaurence Oberman <loberman@redhat.com>
Tested-by: NLaurence Oberman <loberman@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
      96418b5e
  5. 23 2月, 2017 7 次提交
  7. 05 1月, 2017 1 次提交
  9. 18 11月, 2016 1 次提交
  11. 09 11月, 2016 1 次提交
  13. 16 7月, 2016 5 次提交
  15. 22 12月, 2015 2 次提交
  17. 06 6月, 2015 1 次提交
  19. 10 4月, 2015 3 次提交
  21. 17 9月, 2014 1 次提交
  23. 03 6月, 2014 3 次提交
  25. 16 3月, 2014 3 次提交
  27. 27 6月, 2013 1 次提交
  29. 03 5月, 2013 1 次提交
  31. 10 4月, 2013 1 次提交
  33. 30 1月, 2013 1 次提交
  35. 27 11月, 2012 1 次提交
    • J
      [SCSI] lpfc 8.3.36: Fixed boot from san failure · c71ab861
      由 James Smart 提交于 
      Fixed boot from san failure when SLI4 FC device presented on the same PCI bus

The request_firmware interface can induce delays while looking
for firmware files, even if no fw file is present. In some situations
the delays exceeded scan_wait timeouts, resulting in situations in which
the boot device had not been discovered in time.  Boot Device does not
need to be on a lpfc device.

Change request_firmware use to be module paramater driven. Default is to
not attempt firmware download on boot. Add sysfs parameter to invoke
firmware update.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
      c71ab861
  37. 08 10月, 2012 1 次提交
  39. 15 9月, 2012 1 次提交
  41. 14 9月, 2012 2 次提交