Paolo pointed out that irqs are already blocked when irqtime_account_irq()
is called. That means there is no reason to call local_irq_save/restore()
again.
Suggested-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1468421405-20056-6-git-send-email-fweisbec@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Vtime generic irqtime accounting has been removed but there are a few
remnants to clean up:

* The vtime_accounting_cpu_enabled() check in irq entry was only used
  by CONFIG_VIRT_CPU_ACCOUNTING_GEN. We can safely remove it.

* Without the vtime_accounting_cpu_enabled(), we no longer need to
  have a vtime_common_account_irq_enter() indirect function.

* Move vtime_account_irq_enter() implementation under
  CONFIG_VIRT_CPU_ACCOUNTING_NATIVE which is the last user.

* The vtime_account_user() call was only used on irq entry for
  CONFIG_VIRT_CPU_ACCOUNTING_GEN. We can remove that too.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1468421405-20056-4-git-send-email-fweisbec@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

The CONFIG_VIRT_CPU_ACCOUNTING_GEN irq time tracking code does not
appear to currently work right.

On CPUs without nohz_full=, only tick based irq time sampling is
done, which breaks down when dealing with a nohz_idle CPU.

On firewalls and similar systems, no ticks may happen on a CPU for a
while, and the irq time spent may never get accounted properly. This
can cause issues with capacity planning and power saving, which use
the CPU statistics as inputs in decision making.

Remove the VTIME_GEN vtime irq time code, and replace it with the
IRQ_TIME_ACCOUNTING code, when selected as a config option by the user.
Signed-off-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1468421405-20056-3-git-send-email-fweisbec@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Currently, if there was any irq or softirq time during 'ticks'
jiffies, the entire period will be accounted as irq or softirq
time.

This is inaccurate if only a subset of the time was actually spent
handling irqs, and could conceivably mis-count all of the ticks during
a period as irq time, when there was some irq and some softirq time.

This can actually happen when irqtime_account_process_tick is called
from account_idle_ticks, which can pass a larger number of ticks down
all at once.

Fix this by changing irqtime_account_hi_update(), irqtime_account_si_update(),
and steal_account_process_ticks() to work with cputime_t time units, and
return the amount of time spent in each mode.

Rename steal_account_process_ticks() to steal_account_process_time(), to
reflect that time is now accounted in cputime_t, instead of ticks.

Additionally, have irqtime_account_process_tick() take into account how
much time was spent in each of steal, irq, and softirq time.

The latter could help improve the accuracy of cputime
accounting when returning from idle on a NO_HZ_IDLE CPU.

Properly accounting how much time was spent in hardirq and
softirq time will also allow the NO_HZ_FULL code to re-use
these same functions for hardirq and softirq accounting.
Signed-off-by: NRik van Riel <riel@redhat.com>
[ Make nsecs_to_cputime64() actually return cputime64_t. ]
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1468421405-20056-2-git-send-email-fweisbec@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

The pv_time_ops structure contains a function pointer for the
"steal_clock" functionality used only by KVM and Xen on ARM. Xen on x86
uses its own mechanism to account for the "stolen" time a thread wasn't
able to run due to hypervisor scheduling.

Add support in Xen arch independent time handling for this feature by
moving it out of the arm arch into drivers/xen and remove the x86 Xen
hack.
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: NStefano Stabellini <sstabellini@kernel.org>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

This patch adds guest steal-time support to full dynticks CPU
time accounting. After the following commit:

ff9a9b4c ("sched, time: Switch VIRT_CPU_ACCOUNTING_GEN to jiffy granularity")

... time sampling became jiffy based, even if we do the sampling from the
context tracking code, so steal_account_process_tick() can be reused
to account how many 'ticks' are stolen-time, after the last accumulation.
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: NPaolo Bonzini <pbonzini@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1465813966-3116-4-git-send-email-wanpeng.li@hotmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

The callers of steal_account_process_tick() expect it to return
whether a jiffy should be considered stolen or not.

Currently the return value of steal_account_process_tick() is in
units of cputime, which vary between either jiffies or nsecs
depending on CONFIG_VIRT_CPU_ACCOUNTING_GEN.

If cputime has nsecs granularity and there is a tiny amount of
stolen time (a few nsecs, say) then we will consider the entire
tick stolen and will not account the tick on user/system/idle,
causing /proc/stats to show invalid data.

The fix is to change steal_account_process_tick() to accumulate
the stolen time and only account it once it's worth a jiffy.

(Thanks to Frederic Weisbecker for suggestions to fix a bug in my
first version of the patch.)
Signed-off-by: NChris Friesen <chris.friesen@windriver.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/56DBBDB8.40305@mail.usask.caSigned-off-by: NIngo Molnar <mingo@kernel.org>

When profiling syscall overhead on nohz-full kernels,
after removing __acct_update_integrals() from the profile,
native_sched_clock() remains as the top CPU user. This can be
reduced by moving VIRT_CPU_ACCOUNTING_GEN to jiffy granularity.

This will reduce timing accuracy on nohz_full CPUs to jiffy
based sampling, just like on normal CPUs. It results in
totally removing native_sched_clock from the profile, and
significantly speeding up the syscall entry and exit path,
as well as irq entry and exit, and KVM guest entry & exit.

Additionally, only call the more expensive functions (and
advance the seqlock) when jiffies actually changed.

This code relies on another CPU advancing jiffies when the
system is busy. On a nohz_full system, this is done by a
housekeeping CPU.

A microbenchmark calling an invalid syscall number 10 million
times in a row speeds up an additional 30% over the numbers
with just the previous patches, for a total speedup of about
40% over 4.4 and 4.5-rc1.

Run times for the microbenchmark:

 4.4				3.8 seconds
 4.5-rc1			3.7 seconds
 4.5-rc1 + first patch		3.3 seconds
 4.5-rc1 + first 3 patches	3.1 seconds
 4.5-rc1 + all patches		2.3 seconds

A non-NOHZ_FULL cpu (not the housekeeping CPU):

 all kernels			1.86 seconds
Signed-off-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: clark@redhat.com
Cc: eric.dumazet@gmail.com
Cc: fweisbec@gmail.com
Cc: luto@amacapital.net
Link: http://lkml.kernel.org/r/1455152907-18495-5-git-send-email-riel@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Add include asm/paravirt.h to cputime.c, as steal_account_process_tick
calls paravirt_steal_clock, which is defined in asm/paravirt.h.

The ifdef CONFIG_PARAVIRT is necessary because not all archs have an
asm/paravirt.h to include.

The reason why currently cputime.c compiles, even though include
<asm/paravirt.h> is missing, is that on x86 asm/paravirt.h is included
by one of the other headers included in kernel/sched/cputime.c:

On arm and arm64, where I am about to introduce asm/paravirt.h and
stolen time support, without #include <asm/paravirt.h> in cputime.c, I
would get an error.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>

The cputime can only be updated by the current task itself, even in
vtime case. So we can safely use seqcount instead of seqlock as there
is no writer concurrency involved.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1447948054-28668-8-git-send-email-fweisbec@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Readers need to know if vtime runs at all on some CPU somewhere, this
is a fast-path check to determine if we need to check further the need
to add up any tickless cputime delta.

This fast path check uses context tracking state because vtime is tied
to context tracking as of now. This check appears to be confusing though
so lets use a vtime function that deals with context tracking details
in vtime implementation instead.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1447948054-28668-7-git-send-email-fweisbec@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

vtime_accounting_enabled() checks if vtime is running on the current CPU
and is as such a misnomer. Lets rename it to a function that reflect its
locality. We are going to need the current name for a function that tells
if vtime runs at all on some CPU.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1447948054-28668-6-git-send-email-fweisbec@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

When a task runs on a housekeeper (a CPU running with the periodic tick
with neighbours running tickless), it doesn't account cputime using vtime
but relies on the tick. Such a task has its vtime_snap_whence value set
to VTIME_INACTIVE.

Readers won't handle that correctly though. As long as vtime is running
on some CPU, readers incorretly assume that vtime runs on all CPUs and
always compute the tickless cputime delta, which is only junk on
housekeepers.

So lets fix this with checking that the target runs on a vtime CPU through
the appropriate state check before computing the tickless delta.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1447948054-28668-5-git-send-email-fweisbec@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

VTIME_SLEEPING state happens either when:

1) The task is sleeping and no tickless delta is to be added on the task
   cputime stats.
2) The CPU isn't running vtime at all, so the same properties of 1) applies.

Lets rename the vtime symbol to reflect both states.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1447948054-28668-4-git-send-email-fweisbec@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

There is an extra cost in task_cputime() and task_cputime_scaled() when
nohz_full is not activated. When vtime accounting is not enabled, we
don't need to get deltas of utime and stime under vtime seqlock.

This patch removes that cost with adding a shortcut route if vtime
accounting is not enabled.

Use context_tracking_is_enabled() to check if vtime is accounting on
some cpu, in which case only we need to check the tickless cputime delta.
Signed-off-by: NHiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1447948054-28668-3-git-send-email-fweisbec@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

/proc/stats shows invalid gtime when the thread is running in guest.
When vtime accounting is not enabled, we cannot get a valid delta.
The delta is calculated with now - tsk->vtime_snap, but tsk->vtime_snap
is only updated when vtime accounting is runtime enabled.

This patch makes task_gtime() just return gtime without computing the
buggy non-existing tickless delta when vtime accounting is not enabled.

Use context_tracking_is_enabled() to check if vtime is accounting on
some cpu, in which case only we need to check the tickless delta. This
way we fix the gtime value regression on machines not running nohz full.

The kernel config contains CONFIG_VIRT_CPU_ACCOUNTING_GEN=y and
CONFIG_NO_HZ_FULL_ALL=n and boot without nohz_full.

I ran and stop a busy loop in VM and see the gtime in host.
Dump the 43rd field which shows the gtime in every second:

	 # while :; do awk '{print $3" "$43}' /proc/3955/task/4014/stat; sleep 1; done
	S 4348
	R 7064566
	R 7064766
	R 7064967
	R 7065168
	S 4759
	S 4759

During running busy loop, it returns large value.

After applying this patch, we can see right gtime.

	 # while :; do awk '{print $3" "$43}' /proc/10913/task/10956/stat; sleep 1; done
	S 5338
	R 5365
	R 5465
	R 5566
	R 5666
	S 5726
	S 5726
Signed-off-by: NHiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1447948054-28668-2-git-send-email-fweisbec@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

HV_X64_MSR_VP_RUNTIME msr used by guest to get
"the time the virtual processor consumes running guest code,
and the time the associated logical processor spends running
hypervisor code on behalf of that guest."

Calculation of this time is performed by task_cputime_adjusted()
for vcpu task.

Necessary to support loading of winhv.sys in guest, which in turn is
required to support Windows VMBus.
Signed-off-by: NAndrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: NRoman Kagan <rkagan@virtuozzo.com>
Signed-off-by: NDenis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Gleb Natapov <gleb@kernel.org>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

While the current code guarantees monotonicity for stime and utime
independently of one another, it does not guarantee that the sum of
both is equal to the total time we started out with.

This confuses things (and peoples) who look at this sum, like top, and
will report >100% usage followed by a matching period of 0%.

Rework the code to provide both individual monotonicity and a coherent
sum.
Suggested-by: NFredrik Markstrom <fredrik.markstrom@gmail.com>
Reported-by: NFredrik Markstrom <fredrik.markstrom@gmail.com>
Tested-by: NFredrik Markstrom <fredrik.markstrom@gmail.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jason.low2@hp.com
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

ACCESS_ONCE doesn't work reliably on non-scalar types. This patch removes
the rest of the existing usages of ACCESS_ONCE() in the scheduler, and use
the new READ_ONCE() and WRITE_ONCE() APIs as appropriate.
Signed-off-by: NJason Low <jason.low2@hp.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NRik van Riel <riel@redhat.com>
Acked-by: NWaiman Long <Waiman.Long@hp.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1430251224-5764-2-git-send-email-jason.low2@hp.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

On 32 bit systems cmpxchg cannot handle 64 bit values, so
some additional magic is required to allow a 32 bit system
with CONFIG_VIRT_CPU_ACCOUNTING_GEN=y enabled to build.

Make sure the correct cmpxchg function is used when doing
an atomic swap of a cputime_t.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRik van Riel <riel@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: umgwanakikbuti@gmail.com
Cc: fweisbec@gmail.com
Cc: srao@redhat.com
Cc: lwoodman@redhat.com
Cc: atheurer@redhat.com
Cc: oleg@redhat.com
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux390@de.ibm.com
Cc: linux-arch@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/20140930155947.070cdb1f@annuminas.surriel.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

The sig->stats_lock nests inside the tasklist_lock and the
sighand->siglock in __exit_signal and wait_task_zombie.

However, both of those locks can be taken from irq context,
which means we need to use the interrupt safe variant of
read_seqbegin_or_lock. This blocks interrupts when the "lock"
branch is taken (seq is odd), preventing the lock inversion.

On the first (lockless) pass through the loop, irqs are not
blocked.
Reported-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: prarit@redhat.com
Cc: oleg@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1410527535-9814-3-git-send-email-riel@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

The functions task_cputime_adjusted and thread_group_cputime_adjusted()
can be called locklessly, as well as concurrently on many different CPUs.

This can occasionally lead to the utime and stime reported by times(), and
other syscalls like it, going backward. The cause for this appears to be
multiple threads racing in cputime_adjust(), both with values for utime or
stime that is larger than the original, but each with a different value.

Sometimes the larger value gets saved first, only to be immediately
overwritten with a smaller value by another thread.

Using atomic exchange prevents that problem, and ensures time
progresses monotonically.
Signed-off-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: umgwanakikbuti@gmail.com
Cc: fweisbec@gmail.com
Cc: akpm@linux-foundation.org
Cc: srao@redhat.com
Cc: lwoodman@redhat.com
Cc: atheurer@redhat.com
Cc: oleg@redhat.com
Link: http://lkml.kernel.org/r/1408133138-22048-4-git-send-email-riel@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Both times() and clock_gettime(CLOCK_PROCESS_CPUTIME_ID) have scalability
issues on large systems, due to both functions being serialized with a
lock.

The lock protects against reporting a wrong value, due to a thread in the
task group exiting, its statistics reporting up to the signal struct, and
that exited task's statistics being counted twice (or not at all).

Protecting that with a lock results in times() and clock_gettime() being
completely serialized on large systems.

This can be fixed by using a seqlock around the events that gather and
propagate statistics. As an additional benefit, the protection code can
be moved into thread_group_cputime(), slightly simplifying the calling
functions.

In the case of posix_cpu_clock_get_task() things can be simplified a
lot, because the calling function already ensures that the task sticks
around, and the rest is now taken care of in thread_group_cputime().

This way the statistics reporting code can run lockless.
Signed-off-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Daeseok Youn <daeseok.youn@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guillaume Morin <guillaume@morinfr.org>
Cc: Ionut Alexa <ionut.m.alexa@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Michal Schmidt <mschmidt@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: umgwanakikbuti@gmail.com
Cc: fweisbec@gmail.com
Cc: srao@redhat.com
Cc: lwoodman@redhat.com
Cc: atheurer@redhat.com
Link: http://lkml.kernel.org/r/20140816134010.26a9b572@annuminas.surriel.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Change thread_group_cputime() to use for_each_thread() instead of
buggy while_each_thread(). This also makes the pid_alive() check
unnecessary.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Frank Mayhar <fmayhar@google.com>
Cc: Frederic Weisbecker <fweisbec@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Sanjay Rao <srao@redhat.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140813192000.GA19327@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Russell reported, that irqtime_account_idle_ticks() takes ages due to:

       for (i = 0; i < ticks; i++)
               irqtime_account_process_tick(current, 0, rq);

It's sad, that this code was written way _AFTER_ the NOHZ idle
functionality was available. I charge myself guitly for not paying
attention when that crap got merged with commit abb74cef ("sched:
Export ns irqtimes through /proc/stat")

So instead of looping nr_ticks times just apply the whole thing at
once.

As a side note: The whole cputime_t vs. u64 business in that context
wants to be cleaned up as well. There is no point in having all these
back and forth conversions. Lets standardise on u64 nsec for all
kernel internal accounting and be done with it. Everything else does
not make sense at all for fine grained accounting. Frederic, can you
please take care of that?
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1405022307000.6261@ionos.tec.linutronix.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

The steal guest time accounting code assumes that cputime_t is based on
jiffies. So when CONFIG_NO_HZ_FULL=y, which implies that cputime_t
is based on nsecs, steal_account_process_tick() passes the delta in
jiffies to account_steal_time() which then accounts it as if it's a
value in nsecs.

As a result, accounting 1 second of steal time (with HZ=100 that would
be 100 jiffies) is spuriously accounted as 100 nsecs.

As such /proc/stat may report 0 values of steal time even when two
guests have run concurrently for a few seconds on the same host and
same CPU.

In order to fix this, lets convert the nsecs based steal delta to
cputime instead of jiffies by using the right conversion API.

Given that the steal time is stored in cputime_t and this type can have
a smaller granularity than nsecs, we only account the rounded converted
value and leave the remaining nsecs for the next deltas.
Reported-by: NHuiqingding <huding@redhat.com>
Reported-by: NMarcelo Tosatti <mtosatti@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>

As patch "sched: Move the priority specific bits into a new header file" exposes
the priority related macros in linux/sched/prio.h, we don't have to implement
task_nice() in kernel/sched/core.c any more.

This patch implements it in linux/sched/sched.h as static inline function,
saving the kernel stack and enhancing performance a bit.
Signed-off-by: NDongsheng Yang <yangds.fnst@cn.fujitsu.com>
Cc: clark.williams@gmail.com
Cc: rostedt@goodmis.org
Cc: raistlin@linux.it
Cc: juri.lelli@gmail.com
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1390878045-7096-1-git-send-email-yangds.fnst@cn.fujitsu.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

scale_stime() silently assumes that stime < rtime, otherwise
when stime == rtime and both values are big enough (operations
on them do not fit in 32 bits), the resulting scaling stime can
be bigger than rtime. In consequence utime = rtime - stime
results in negative value.

User space visible symptoms of the bug are overflowed TIME
values on ps/top, for example:

 $ ps aux | grep rcu
 root         8  0.0  0.0      0     0 ?        S    12:42   0:00 [rcuc/0]
 root         9  0.0  0.0      0     0 ?        S    12:42   0:00 [rcub/0]
 root        10 62422329  0.0  0     0 ?        R    12:42 21114581:37 [rcu_preempt]
 root        11  0.1  0.0      0     0 ?        S    12:42   0:02 [rcuop/0]
 root        12 62422329  0.0  0     0 ?        S    12:42 21114581:35 [rcuop/1]
 root        10 62422329  0.0  0     0 ?        R    12:42 21114581:37 [rcu_preempt]

or overflowed utime values read directly from /proc/$PID/stat

Reference:

  https://lkml.org/lkml/2013/8/20/259Reported-and-tested-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Cc: stable@vger.kernel.org
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20130904131602.GC2564@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Use of a this_cpu() operation reduces the number of instructions used
for accounting (account_user_time()) and frees up some registers. This is in
the scheduler tick hotpath.
Signed-off-by: NChristoph Lameter <cl@linux.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/00000140596dd165-338ff7f5-893b-4fec-b251-aaac5557239e-000000@email.amazonses.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

The vtime delta update performed by get_vtime_delta() always check
that the source of the snapshot is valid.

Meanhile the snapshot updaters that rely on get_vtime_delta() also
set the new snapshot origin. But some of them do this right before
the call to get_vtime_delta(), making its debug check useless.

This is easily fixable by moving the snapshot origin update after
the call to get_vtime_delta(). The order doesn't matter there.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>

The cputime accounting in full dynticks can be a subtle
mixup of CPUs using tick based accounting and others using
generic vtime.

As long as the tick can have a share on producing these stats, we
want to scale the result against CFS precise accounting as the tick
can miss some task hiding between the periodic interrupt.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>

If no CPU is in the full dynticks range, we can avoid the full
dynticks cputime accounting through generic vtime along with its
overhead and use the traditional tick based accounting instead.

Let's do this and nope the off case with static keys.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>

get_vtime_delta() must be called under the task vtime_seqlock
with the code that does the cputime accounting flush.

Otherwise the cputime reader can be fooled and run into
a race where it sees the snapshot update but misses the
cputime flush. As a result it can report a cputime that is
way too short.

Fix vtime_account_user() that wasn't complying to that rule.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>

Some generic vtime APIs check if the vtime accounting
is enabled on the local CPU before doing their work.

Some of these are not needed because all their callers already
take care of that. Let's remove the checks on these.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>

Optimize guest entry/exit APIs with static keys. This minimize
the overhead for those who enable CONFIG_NO_HZ_FULL without
always using it. Having no range passed to nohz_full= should
result in the probes overhead to be minimized.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>

Update a stale comment from the old vtime era and document some
locking that might be non obvious.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>

While computing the cputime delta of dynticks CPUs,
we are mixing up clocks of differents natures:

* local_clock() which takes care of unstable clock
sources and fix these if needed.

* sched_clock() which is the weaker version of
local_clock(). It doesn't compute any fixup in case
of unstable source.

If the clock source is stable, those two clocks are the
same and we can safely compute the difference against
two random points.

Otherwise it results in random deltas as sched_clock()
can randomly drift away, back or forward, from local_clock().

As a consequence, some strange behaviour with unstable tsc
has been observed such as non progressing constant zero cputime.
(The 'top' command showing no load).

Fix this by only using local_clock(), or its irq safe/remote
equivalent, in vtime code.
Reported-by: NMike Galbraith <efault@gmx.de>
Suggested-by: NMike Galbraith <efault@gmx.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Simple cleanup.
Reported-by: NPeter Zijlstra <peterz@infradead.org>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/1367501673-6563-1-git-send-email-sgruszka@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Dave Hansen reported strange utime/stime values on his system:
https://lkml.org/lkml/2013/4/4/435

This happens because prev->stime value is bigger than rtime
value. Root of the problem are non-monotonic rtime values (i.e.
current rtime is smaller than previous rtime) and that should be
debugged and fixed.

But since problem did not manifest itself before commit
62188451 "cputime: Avoid
multiplication overflow on utime scaling", it should be threated
as regression, which we can easily fixed on cputime_adjust()
function.

For now, let's apply this fix, but further work is needed to fix
root of the problem.
Reported-and-tested-by: NDave Hansen <dave@sr71.net>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: rostedt@goodmis.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1367314507-9728-3-git-send-email-sgruszka@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Due to rounding in scale_stime(), for big numbers, scaled stime
values will grow in chunks. Since rtime grow in jiffies and we
calculate utime like below:

	prev->stime = max(prev->stime, stime);
	prev->utime = max(prev->utime, rtime - prev->stime);

we could erroneously account stime values as utime. To prevent
that only update prev->{u,s}time values when they are smaller
than current rtime.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: rostedt@goodmis.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1367314507-9728-2-git-send-email-sgruszka@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>